INSTALLATION INSTRUCTIONS GB-PLEN1 Equipment Enclosure for Plenum Ceilings NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044 ©Premier Mounts 2008 9534-003-003-00 AUSTRALIA, NEW ZEALAND, OCEANIA (DISTRIBUTOR) P.O.
GB-PLEN1 Table of Contents Warning Statements Parts List Installation Tools GB-PLEN1 Installation with PP-FCTA GB-PLEN1 Installation with PP-FCMA Technical Specifications Warranty 2 3 3 4 7 9 10 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE.
GB-PLEN1 Parts List This accessory is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
GB-PLEN1 The GB-PLEN1 is designed for use with either the PP-FCTA or PP-FCMA. After installing your selected false-ceiling adapter, follow the instructions on the following pages to secure the GB-PLEN1. GB-PLEN1 Installation with PP-FCTA Mounting Rails PP-FCTA Plate Upper Adapter Plate Wing Nut Upper Adapter Plate PP-FCTA Step 1. Loosen the wing nuts (do not remove) on the upper adapter plate. Step 2. Slide the mounting rails (threaded holes facing up) between the upper adapter plate and the PP-FCTA.
GB-PLEN1 You may wish to pre-install your electronic components inside the enclosure at this time. If so, make sure to leave the mounting slots accessible. Mounting Points M5 x 10mm Screws Step 5. Locate the four (4) mounting holes on the mounting rails. Step 6. Align the mounting slots on the GB-PLEN1 with the mounting holes on the mounting rails. Step 7. Use four (4) M5 x 10mm screws to attach the GB-PLEN1 to the mounting rails.
GB-PLEN1 If you did not pre-install electrical components, then you may now install all power and signal equipment. A qualified electrician should make any power connections to the GB-PLEN1. Padlock Hasp (optional) M5 x 10mm Screws Step 8. Place the padlock hasp on the inside of the GB-PLEN1 (optional). Completed Attachment When attaching the padlock hasp, make sure the flat side is resting against the inside wall of the GB-PLEN1. Step 9.
GB-PLEN1 The GB-PLEN1 is designed for use with either the PP-FCMA or PP-FCTA. After installing your selected false-ceiling adapter, follow the instructions on the following pages to secure the GB-PLEN1. GB-PLEN1 Installation with PP-FCMA Mounting Rails Adapter Plate Mounting Screw Screwdriver M5 x 10mm Screws PP-FCMA Step 1. Loosen the four (4) mounting screws that are located on the underside of the PP-FCMA. Do not completely remove these screws. Step 2.
GB-PLEN1 If you did not pre-install electrical components, then you may now install all power and signal equipment. A qualified electrician should make any power connections to the GB-PLEN1. Padlock Hasp (optional) M5 x 10mm Screws Step 6. Place the padlock hasp on the inside of the GB-PLEN1 (optional). Completed Attachment When attaching the padlock hasp, make sure the flat side is resting against the inside wall of the GB-PLEN1. Step 7.
GB-PLEN1 Technical Specifications All measurements are in inches(mm).
GB-PLEN1 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.