INSTALLATION INSTRUCTIONS LPFM1532 Universal Low Profile Flat Mount for 15” to 32” Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044 ©Premier Mounts 2009 9531-201-001-02 EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710
LPFM1532 Table of Contents Warning Statements Parts List Installation Tools Wood Stud Installation Concrete Surface Installation Determining the Mounting Hardware Universal Spacers Cover Plate Installation Adapter Plate Installation Cover Plate Installation with Adapter Plates Attached (Optional) Flat Panel Installation Technical Specifications Warranty 2 3 3 4 5 6 6 7 7 8 9 10 11 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UND
LPFM1532 Parts List Congratulations on the purchase of your new Premier Mounts LPFM1532 flat panel mount. This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800) 368-9700.
LPFM1532 Wood Stud Installation Prior to installation, the two (2) M6 x 75mm Phillips head locking screws must be removed. These two screws are located on the bottom of the LPFM1532. Visual Centering Diamond - The visual centering diamond will allow you to determine the center of the wood stud. It will also allow you to determine the exact center for the flat panel placement on the wall. The visual centering diamond will work in conjunction with the visual stud guide.
LPFM1532 Concrete Surface Installation You will have four (4) mounting holes when installing into concrete. Step 1. Use the visual centering diamond to help determine the placement of the back plate. Step 2. Once the mounting placement has been determined, use a pencil to mark the mounting points. Step 3. Drill the mounting holes using a 1/8” drill bit where the pencil marks have been made. 1/8” Bit Pilot Hole So lid Su rfa Step 4. Place the #10 anchor into the hole and tap into place. Step 5.
LPFM1532 Determining the Mounting Hardware Step 1. Step 2. Step 3. Step 4. Step 5. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel. Using a pencil, mark the depth of the thread insert on the thread depth indicator (Figure 2). Compare and verify the depth of the remaining thread inserts. Locate the correct diameter screw for the thread insert. Compare your thread depth indicator marking to the screw length.
LPFM1532 Cover Plate Installation Mounting Hardware Slotted Opening Cover Plate Securing Screw Mounting Hardware Mounting Point Flat Panel Step 1. Secure the cover plate to the flat panel using four (4) Phillip screws (supplied). Step 2. The slotted opening must be facing up and the flat surface touching the flat panel surface. DO NOT OVERTIGHTEN THE MOUNTING SCREWS Universal Spacer Recessed VESA 75mm/100mm Pattern Universal spacer stacking is limited to five (5) spacers max for each mounting screw.
LPFM1532 Step 2. Insert four (4; two on each side) M6 x 8mm screws. Tighten using a long Phillips head screwdriver.
LPFM1532 200 x 100 Installation LPFM1532 Mounting Hardware Stacked Universal Spacers Mounting Hardware Flat Panel Installation Mounting Slot So lid Su rfa c Mounting Tab So e Ci nd er Blo lid Su rfa ce Ci ck nd er Blo ck M6 x 75mm Phillips Head Screws Screwdriver The cover plate mounting slot must be facing up. Step 1. Lower the flat panel onto the wall plate so that the mounting tab is inserted into the mounting slot.
LPFM1532 Technical Specifications All measurements are in inches [mm]. B C A B Page 10 D C A C D A 75mm D 100mm A B A D C A Please refer to the hardware pack that is included with the LPFM1532 to determine the correct mounting hardware for your application. NOTE: A. 200 X 100 VESA Pattern M4 x 10mm Phillips Flat Head screws only. B. 200 X 200 VESA Pattern If an M4 is to be used for location B, an M4 washer must be used as well. C. 100 X 100 VESA Pattern D.
LPFM1532 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
