CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount for 42˝ to 63˝ Flat Panels Model: P4263F NORTH AMERICA EUROPE 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888 Other Locations Phone: (001)-714-632-7100 Fax: (001)-714-632-1044 Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 9531-203-C01-03
P4263F Contents Weight Limit. ................................................................................................................................................................................. 2 Warning Statements. .................................................................................................................................................................... 2 Installation Tools. ..............................................................................................
P4263F Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store.
P4263F Parts List (cont’d) Mounting Hardware M4 x 16mm Screw (Qty 6) M8 x 16mm Screw (Qty 6) M4 x 25mm Screw (Qty 6) M8 x 25mm Screw (Qty 6) M4 x 30mm Screw (Qty 6) M8 x 30mm Screw (Qty 6) M5 x 16mm Screw (Qty 6) M8 x 45mm Screw (Qty 6) M5 x 25mm Screw (Qty 6) M8 x 70mm Screw (Qty 4) M5 x 30mm Screw (Qty 6) M6 x 16mm Screw (Qty 6) M6 x 25mm Screw (Qty 6) M6 x 30mm Screw (Qty 6) M6 x 45mm Screw (Qty 6) Page 4 Visit the Premier Mounts website at http://www.premiermounts.
P4263F Features Leveling Screws Allows for leveling adjustments of the flat panel after mounting. Cable/Electrical Cut Out A large cut out on the wall plate allows for easy cable access and power distribution installations. Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up. Low Profile Design Holds the flat panel less than 1˝ from the wall. Mounting Slots Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel.
P4263F Installing the Wall Plate Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the P4263F wall mount indicates which edge is the top. Mounting Safety Two people are recommended to for the installation of this mount. Determining the Mounting Surface If you will be installing your P4263F mount to wood studs, proceed to the “Wood Stud Installation” section.
P4263F Installing the Wall Plate (cont’d) Step 3 Drill a “pilot hole” in the center of the upper right mark using a ¼˝ drill bit and power drill. Only use a ¼˝ drill bit when drilling the pilot holes. Step 4 Place the wall plate against the wall and align it with the pilot hole. Insert one (1) 5/16˝ x 3˝ lag bolt and one (1) 5/16˝ washer into the upper right mounting hole and tighten using a socket wrench and ½˝ socket. Do not overtighten the lag bolt. Step 5 Level the wall plate.
P4263F Installing the Wall Plate (cont’d) Step 7 Insert one (1) 5/16˝ x 3˝ lag bolt and one (1) 5/16˝ washer into each pilot hole. Tighten all lag bolts using a socket wrench and ½˝ socket. Do not overtighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. Proceed to the “Installing the Mounting Bracket” section. Concrete Installation The supplied 5/16˝ concrete wedge anchors must be used for concrete installation.
P4263F Installing the Wall Plate (cont’d) Step 3 Insert a concrete wedge anchor into each hole. If necessary, lightly tap each concrete wedge anchor into place with a hammer. Remove the nuts and washers from all four (4) concrete wedge anchors. Step 4 Place the wall plate against the wall over the threaded shafts of the concrete wedge anchors. Replace the washers which you removed from the concrete wedge anchors with the 5/16˝ washers shown in the parts list on Page 3.
P4263F Installing the Wall Plate (cont’d) Step 2 Place the wall plate against the wall in the desired viewing location. Adjust the wall plate to match the locations of the steel studs. Level the wall plate. Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors. Set the wall plate to one side in a safe location. Step 3 Use a power drill and 7/16˝ drill bit to drill a hole at each of the marks. Insert a steel stud anchor into each hole.
P4263F Installing the Wall Plate (cont’d) Step 5 Align the wall plate over the steel stud anchor sleeves. X Insert a steel stud anchor screw and a 5/16˝ washer into each steel stud anchor sleeve. Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug. X Do not overtighten the steel stud anchor screws. Do not use a power drill to tighten the steel stud anchor screws. Proceed to the “Installing the Mounting Bracket” section.
P4263F Installing the Mounting Bracket (cont’d) Universal Washer Installation Premier Mounts’ Universal Washers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat panels. M8 M5, M6 M4 Do not place excessive pressure on the back of the flat panel, as this may damage your flat panel. The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown.
P4263F Installing the Mounting Bracket (cont’d) Locking and Leveling Screw Installation Leveling Screw Installation You must install the leveling screws before you attach the mounting bracket to the back of the flat panel. The leveling screws consists of two (2) M6 x 120mm screws. Thread one (1) leveling screw into the top mounting hole on each of the mounting brackets. Make sure the leveling screw is securely threaded into the mounting tab before proceeding.
P4263F Lock-It™ Security Barrel Installation (Optional) Optional security configurations include: - PCB-CSL1 (sold separately) - Padlock (Combination or Keyed; commercially available) Mounting Tab Please read the following directions to install the security barrel: the locking screw from the mounting Remove bracket. the locking screw into and through the Place security barrel (see illustration below). the locking screw and security barrel into Re-insert the mounting bracket.
P4263F Attaching the Flat Panel to the Wall Plate This section requires two people. Do not release your flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel. Raise the flat panel past the top and bottom mounting rails on the wall panel. Slide the flat panel down slowly, keeping it close to the wall. Engage the top and bottom mounting brackets to the rails of the wall plate.
P4263F Utilizing the Security Barrel Your P4263F Mount includes one (1) Security Barrel which can provide additional theft deterrence for your flat panel. PCB-CSL1 Security Cable - Thread the cable through the hole on the security barrel. Attach the PCB-CSL1 locking mechansim and secure it using the supplied key. Padlock - Place the locking hook through the hole of the security barrel. Snap lock and locking hook together.
P4263F Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.