INSTALLATION MANUAL PBL-UMS (Black) PBL-UMW (White) PBL UNIVERSAL PROJECTOR MOUNT NORTH AMERICA EUROPE 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044 ©Premier Mounts 2010 9530-002-011-09
PBL UNIVERSAL PROJECTOR MOUNT Table of Contents Warning Statements .......................................................................................................................................................... - 2 Parts List ........................................................................................................................................................................... - 3 Installation Tools ...............................................................................
PBL UNIVERSAL PROJECTOR MOUNT Parts List This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800) 368-9700. Upper Assembly® (Qty 1) Universal Mounting Bracket (Qty 1) #14 x 2” Wood Screws (Qty 3) M2.
PBL UNIVERSAL PROJECTOR MOUNT A B C D E F G H I J K L M Single Wooden Stud Mounts Solid Structure Mounting Points Ceiling Plate Security Allen Wrench Extension Tension Knobs Safety Knob Security Screws Leveling Screws Universal Mounting bracket Leg Assembly Projector (not included) Tri-Lock Opening Option 1 A B C D E F G H K NOTE: The four (two-piece) leg assemblies can be used as single leg or any combination of single and dual legs together as shown in Options 1 and 2.
PBL UNIVERSAL PROJECTOR MOUNT Features Congratulations on your recent purchase of your PBL Universal Projector Mount. This mounting system is designed for projectors weighing 40lbs. (18.14 kg) or less. The mount is very easy to install and loaded with additional “no cost” installation features built into the mount. These features allow you to optimize your projector’s position to the screen for best projector performance and picture quality. • • • • • • • • • Page 5 Adjustable-height 9” – 12.
PBL UNIVERSAL PROJECTOR MOUNT Projector Preparation Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the projector. THE PROJECTOR IS FRAGILE. HANDLE WITH CARE AT ALL TIMES. Review the projectors manufacture’s operation manual and refer to the ceiling mounting section of the operator’s manual.
PBL UNIVERSAL PROJECTOR MOUNT B A Upper Assembly Safety Knob Tension Knobs Rotate 180° To unlock C Tri-Lock Opening Figure 2.
PBL UNIVERSAL PROJECTOR MOUNT Bracket Installation Only attach to the projector manufacturer’s specified mounting points on the projector chassis with a minimum of three mounting legs. Please follow all safety instructions specified by the projector manufacturer as well as the safety instructions outlined in this manual. The two-piece mounting legs are designed to allow for the positioning of each leg around projector air vents located on the base of the projector.
PBL UNIVERSAL PROJECTOR MOUNT Leveling the Mounting Bracket Secure but do not over tighten the mounting hardware. Failure to do so will result in damaging the threads in the projector. Step 1. Rotate the leveling barrels to level the mounting bracket. Step 2. Position the mounting bracket so that it avoids most, if not all, ventilation points (including lamp and filter access doors). Step 3.
PBL UNIVERSAL PROJECTOR MOUNT Securing the Upper Assembly Ceiling Plate Review your projector’s owner’s manual to determine what distance is recommended from the front of the lens to the edge of the screen for best picture ratio. However in most home theater and office ceiling mount installations this is not practical as the projector would be to low within the room.
PBL UNIVERSAL PROJECTOR MOUNT Securing the Projector to the Upper Assembly Step 1. Make sure the three-knurl knobs are loosened to fully expose to the “tri-lock” mounting plate in the base of the upper assembly. Step 2. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating portion of the upper assembly. Step 3.
PBL UNIVERSAL PROJECTOR MOUNT Final Adjustments Step 1. With the projector secured in the mount and power on and signal supplied to the projector you can now proceed with the final height, tilt, roll and yaw to optimize the projected image. Wooden Stud A A The height can be adjusted by rotating the PBC clockwise (higher) / counterclockwise (lower). Once the height is achieved, tighten the locking set screw using the supplied Security Allen Wrench.
PBL UNIVERSAL PROJECTOR MOUNT Plastic Cap Installation Step 1. Once all the final adjustments have been finished install the plastic caps on the leveling barrels (Figure 8). Figure 8.
PBL UNIVERSAL PROJECTOR MOUNT Technical Specifications All measurements are in inches(mm). Figure 9.
PBL UNIVERSAL PROJECTOR MOUNT Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product.