Available From: eFilterWater CLICK HERE Your Health Matters! INSTALLATION, OPERATION AND MAINTENANCE MANUAL Warning Please read carefully before proceeding with installation. Your failure to follow any attached instructions or operating parameters may lead to the products failure and possible damage to property.
Thank you for your purchase of a state of the art Watts Premier Reverse Osmosis (RO) water treatment system. Water quality concerns are quickly becoming more of a focus for the public. Lately you may have heard about contaminants in the drinking water, such as arsenic, chromium, cryptosporidium or Giardia. There may also be some local water issues in your area such as high levels of lead and copper.
With proper installation and maintenance, this system will provide you with high quality water for years to come. All of Watts Premier’s water enhancement products are rigorously tested by independent laboratories for safety and reliability. If you have any questions or concerns, please contact our customer service department at 1-800-752-5582 (outside USA 623-931-1977) or refer to our on-line trouble shooting at www.wattspremier.com. Table of Contents Operational Parameters ..............................
Operational Parameters Operating Temperatures: Maximum 100°F (37.8°C) Minimum Operating Pressure: Maximum 85 psi (6.0 kg/cm2) Minimum pH Maximum 11 Minimum 2 Parameters: Iron: Maximum 0.2 ppm TDS (Total Dissolved Solids): < 1800 ppm Turbidity: < 5NTU 40°F (4.4°C) 40 psi (2.80 kg/cm2) Hardness: Recommended hardness should not exceed 10 grains per gallon, or 170 ppm. System will operate with hardness over 10 grains but the membrane life will be shortened.
Drill a Hole for the Faucet in a Porcelain Sink Note: Most sinks are predrilled with 1 ½” or 1 ¼” diameter hole that you can use for your RO faucet. (if you are already using it for a sprayer or soap dispenser, see step 1). Porcelain sinks are extremely hard and can crack or chip easily. Use extreme caution when drilling. Premier accepts no responsibility for damage resulting from the installation of faucet.
WATTS Premier (Top Mount) Monitor Faucet Installation Mounting Hole Size Torque on Toggle Bolt Step 1 Step 2 Minimum Maximum 1.00” 1.25” 5lb.in. (max) Watts Monitor Faucet P/N: 116074 (Chrome Monitor with Air Gap) P/N: 116075 (Chrome Monitor) Gather and identify the faucet pieces. Remove faucet base & faucet spout from their respective plastic bags. From above the sink, feed the faucet tubing & toggle bolt down through the 1.00” to 1.25” mounting hole in the sink.
AG-SS with TDS Monitor Faucet Installation Note: If using the AG-SS TDS Monitor Air Gap Faucet , a 1 1/4” hole will be required. Step 6 Remove the stem nut and the tubing guide from the faucet. Make sure the soft rubber gasket remains, so it will be on top of the counter when installed. From above the sink, feed the tubing and faucet stem down through the 1¼ inch mounting hole in the sink.
AG-SS with Monitor Faucet Installation - Part# 116061 Note: If using the AG-SS Monitor Air Gap Faucet , a 1 1/4” hole will be required. Gather and identify the faucet pieces. Step 6 Remove faucet and small parts from plastic bag. Slip the gasket over the threaded stem to the faucet flange. From above the sink, feed the tubing and faucet stem down through the 1¼ inch mounting hole in the sink.
Adapta Valve Installation - Part# 134007 Configuration for 3/8” compression fittings Configuration for 1/2” compression fittings Hot Supply Cold Supply Step 11 Turn off the cold water supply to the faucet by turning the angle stop valve completely off. Step 12 Attach adapta valve as illustrated in the three photos above, choosing the configuration that fits your plumbing. (When attaching the adapta valve to straight pipe threads, use Teflon tape on the treads.
Drain Saddle Installation - Part# 164016 Drain Saddle fits standard 1 ¼” – 1 ½” drain pipes Step 14 Gather the pieces of the drain saddle 1 Black compression nut 1 Semicircle bracket with opening 2 Screws 1 Foam washer 2 Nuts for screws 1 Semicircle bracket Step 15 The small square black foam gasket with a circle cut out of the middle must be applied to the inside of the drain saddle. Remove sticky tape backing and stick to the drain saddle as shown.
Connect Blue Tube from TANK port on RO Module to the Tank Step 19 Position tank in desired location. Stand it upright or lay it on its side (using the black plastic stand). Measure the blue tube from the RO module port marked TANK over to the tank and cut it to desired length. Step 20 Insert the blue 3/8” tube into the compression nut as far as it will go. Tighten the compression nut securely with a wrench.
3/8” Black Tube Connection from faucet Note: The tubing must be as SHORT and STRAIGHT as possible to the drain saddle, making a downward slope from module to drain saddle to allow for proper drainage. Step 24 Measure the black tube from faucet to the black drain saddle and make a straight cut through tube. Step 25 Remove black plastic nut from drain saddle. Slip black tube through black nut.
Connect the Red Tube from Faucet to RO Module Step 26 Insert the red 1/4” tube from the faucet into the port on the module marked DRAIN. Make sure the tube is pushed in all the way to the tube stop. Final Filter Installation Step 27 The Final Filter and 2 white plastic connectors are in the parts bag. (One 1/4” smaller & one 3/8” larger) Step 28 Remove the caps from the final filter.
Start up Instructions Step 1 Turn on the incoming cold water at the angle stop valve. Open the needle valve on the brass Adapta Valve by turning counter clockwise. Check the system for leaks and tighten any fitting as necessary. (Check frequently over the next 24 hours to ensure no leaks are present). Step 2 Open the RO faucet and leave it open until water begins to trickle out, (it will come out slowly). Step 3 After water trickles out of the faucet, close RO faucet so the tank will fill with water.
6 Month System Maintenance Note: The KP-5 R.O. unit is equipped with annual filters, therefore require only one annual change. Watts Premier sells a filter change kit which includes pre-filters, a final filter, connectors, and a wrench. √ One 10” sediment filter (part no. 104017) √ Two 10” carbon filters (part no. 101009) √ Bucket to catch water from filter housings. Step 1 Turn off incoming water supply to the RO by turning the needle valve on the adapta valve clockwise.
Annual Maintenance Step 1 Annual sanitizing of unit is recommended. Turn off incoming water supply. Remove sediment & carbon filters from filter housing. Step 2 Open Membrane vessel and remove the membrane from the membrane vessel. Replace empty membrane vessel onto the unit. Step 3 Leave filters out, replace the last two (of three) empty filter housings (hand tight) onto unit.
Step 3 Pull firmly on the membrane to remove from the housing and discard. Step 4 Unwrap new membrane and lubricate the o-rings with water soluble lubrication such as KY Jelly ® before inserting into housing. Insert end with the two black O-rings into the cap. Twist the membrane as you push firmly into the cap. Step 5 Replace the vessel onto the cap by turning clockwise. Tighten securely. Cleaning the Flow Restrictor Step 6 The flow restrictor plug (part no.
Check Air Pressure in the Tank Note: Check air pressure when tank is empty of water! Check air pressure in the tank when you notice a decrease in available water from the RO system. Step 1 It is recommended that you drain the tank of water, and then pump up the RO tank in order to ensure all water is out of the tank. Air can be added with a bicycle pump. Step 2 Once all water in the tank is purged out, check air pressure of the tank. If you added air to the tank, it will be higher than 5 - 7 psi.
TROUBLE SHOOTING Problem Cause 1. Low/Slow Production Low Water Pressure Solution Assure a minimum of 40 psi incoming water pressure. Premier sells a booster pump if home water pressure is low. Maker sure water supply is turned on and Adapta Valve is all the way open Check tubing and straighten or replace as necessary. Replace pre-filters. Replace membrane and clean flow restrictor. Crimps in tubing Clogged pre-filters Fouled membrane 2.
Arsenic Fact Sheet Arsenic (As) is a naturally occurring contaminant found in many ground waters. Arsenic in water has no color, taste or odor. It must be measured by an arsenic test kit or lab test. Public water utilities must have their water tested for arsenic. You can obtain the results from your water utility contained with in your consumer confidence report. If you have your own well, you will need to have the water evaluated.
California Certification State State of ofCalifornia California Departmentof ofHealth PublicServices Health Department Water Treatment Device Certificate Number 00 - 1452 Date Issued: October 17, 2005 Trademark/Model Designation Watts Premier Deluxe Plus Watts Premier Ultra 5 Watts Premier PUR-TEK Watts Premier Watts 25 Watts Premier RO-TFM-5SV Watts Premier RO-TFM-4SV Watts RO-4 Watts RO-5 Watts Premier WP-5 Watts Premier WP-4 Watts Premier KP-4 Watts Premier KP-5 Watts Premier RO-4M Watts Premier RO-5M
Performance Data Sheet WP-5, KP-5, RO5-M Watts Premier Inc. 1725 W. Williams Drive C-20 Phoenix, AZ 85027 USA (623) 931-1977 wpmail@wattsind.com GENERAL USE CONDITIONS: 1. S� . DO NOT use with wate� ed for cyst reduction may be used on disinfected water that may contain filterable cysts. 2. Operating Temperature: Maximum: 100°F (40.5°C) Minimum: 40° (4.4°) 3. Operating Water Pressure: Maximum: 85 psi (7.0kg/cm2) Minimum: 40 psi (2.8kg/cm2) 4. pH 2 to 11 5. No iron present in incoming feed water supply. 6.
Performance Data Sheet B-RO5M-50, WP5-50 Watts Premier Inc. 1725 W. Williams Drive C-20 Phoenix, AZ 85027 USA (623) 931-1977 wpmail@wattsind.com GENERAL USE CONDITIONS: 1. S� . Do not use with wate� ed for cyst reduction may be used on disinfected water that may contain filterable cysts. 2.
9 23 18 8 22 18 12 6 1 7 7 7 7 7 7 15 3 3 14 4 16 13 20 17 5 19 5 5 11 21 10 2 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 QTY 1 1 2 1 3 1 6 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 Page 24 PART NU 100014 100037 101009 104017 113018 113035 113041 113045 116022 116058 119007 125017 125032 131002 131012 131017 134007 146004 164016 400031 560006 560008 610023 Parts List DESCRIPTION GAC-IL-10-1-4 F-Premier GAC-KDF 802 10 inch CARBON BLOCK-10 INCH-5M-CTG-WATTS SED-SPUN
Other Products from Watts Premier Watts Premier has other fine water filtration products and accessories to enhance your water and to compliment your existing RO System. Listed on the next several pages are only a few of the items we offer. Visit our website at www.wattspremier.com or call our Customer Service Representatives at 1-800-752-5582 (inside USA) 1-623-931-1977 (outside USA) for more products.
Top Mount Faucets by Watts Premier These attractively designed faucets feature a long reach spout to compliment all styles of kitchen decor. The unique top mount design allows for easy above counter installation. The Monitored version of this faucet has an LED light that turns red to notify you for filter replacement. Part No.
Removing chlorine from your shower Special Chlorgon & KDF media – More effective then carbon medias with hot water applications in the removal of the following. √ √ √ √ √ Iron oxide (rust water) Free Chlorine (CL-) Combined Chlorine (Sodium Hypochlorite) √ Dirt, sediment √ Odors Hydrogen Sulfide (Rotten egg smell) Plus, its pH balanced.
WARRANTY REGISTRATION Thank you for selecting Watts Premier for your water filtration needs. 4 Ways to Register 1. Online at www.wattspremier.com Register your product online and receive a 5% discount on your next online order, Plus receive reduced shipping. 2. Call in your information 1-800-752-5582 Call and we will enter your information. 3. Fax in your information Fax this form directly to us. 623-931-0191 4. Mail in the information. Please complete the form below. Mail to: Watts Premier 1725 W.
WARRANTY REGISTRATION Please Fill out and keep for your Records First Name:_________________________ Last Name:____________________________ Address: ________________________________________ City: ____________________ State: _______________________________________ Zip Code: ___________________ Country: USA CANADA MEXICO OTHER ____________ Phone # ______-__________ -__________ Email Address: ______________________ Date of Purchase: ___________________ Date of Install: _______________________ Installe
Service Record Serial No.
Available From: eFilterWater CLICK HERE Your Health Matters! Page 31
Limited Warranty What your Warranty Covers: If any part of your WATTS PREMIER Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return unit after obtaining a return authorization (see below), less tank, within 3 year of original retail purchase, WATTS PREMIER will repair or, at WATTS PREMIER’S option, replace the system at no charge. How to obtain Warranty Service: For warranty service, call 1-800-752-5582 for a return authorization number.
