SPI-EXT SpiroLock™ Universal Projector Mount With Extension INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES 9530-005-061-04
SPI-EXT Contents Weight Limit...................................................................................................................................................................... 2 Warning Statements......................................................................................................................................................... 2 Installation Tools.........................................................................................................................
SPI-EXT Installation Tools The following tools may be required depending upon your particular installation. They are not included. Electronic Stud Finder Hand Held Drill Pencil Protective Eyewear Masonry Drill Bit Ladder ⅛˝ Wood Drill Bit Phillips Tip Screwdriver Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
SPI-EXT Features The SpiroLock™ Universal Projector Mount is easy to install. Snap and lock the projector onto the mount, then rotate and pivot freely for the optimal viewing angle. The Lock-It™ security screws and leveling barrel add an extra layer of security and theft deterrence. Tool-Free Adjustment Precise yaw, pitch and roll adjustments without requiring specialized tools. Ceiling Plate Can easily be installed on either a wood stud or solid ceiling.
SPI-EXT Installing the SpiroLock™ With Extension Mount Introduction Your SpiroLock™ mount may be secured to either a single ceiling stud or a solid surface ceiling, such as concrete. Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product. Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation.
SPI-EXT Installing the SpiroLock™ With Extension Mount (cont’d) Wood Stud Installation Step 1 ➊➊ Use a stud finder to locate a ceiling stud closest to ➋➋ ➌➌ your desired installation location. Identify the center of the ceiling stud. Use a pencil to mark the location of the ceiling stud center. The target arrow indicates the direction of the projector screen relative to the projector mount. CSe tud nte r Step 2 ➊➊ Place the SpiroLock™ Ceiling Plate against the ➋➋ ceiling.
SPI-EXT Installing the SpiroLock™ With Extension Mount (cont’d) Step 4 ➊➊ Insert one (1) #14 x 2˝ screw through each of the mounting holes (A) on the bottom of the SpiroLock™ Ceiling ➋➋ Plate and into the pilot holes. Tighten each screw until the SpiroLock™ Ceiling Plate is secure against the ceiling. Do not overtighten the #14 x 2˝ screws. Proceed to the “Attaching the Projector Plate” section on page 9.
SPI-EXT Installing the SpiroLock™ With Extension Mount (cont’d) Step 1 ➊➊ Place the SpiroLock™ Ceiling Plate into position ➋➋ against the ceiling. Use a pencil and mark four (4) mounting hole locations through each of the mounting points (B) in the SpiroLock™ Ceiling Plate. The target arrow indicates the direction of the projector screen relative to the projector mount. Step 2 ➊➊ Drill a hole at each mark using the appropriate ➋➋ ➌➌ diameter masonry bit for your wedge anchor.
SPI-EXT Attaching the Projector Plate Selecting the Mounting Hardware ➊➊ Insert a small straw or toothpick into the threaded ➋➋ ➌➌ ➍➍ ➎➎ inserts found on the bottom or top of the projector. Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. Mark the straw or toothpick 1/8” above the depth of the threaded insert, as shown in Figure 1.
SPI-EXT Attaching the Projector Plate (cont’d) Step 2 Insert the mounting hardware, as determined in the “Selecting the Mounting Hardware” section on page 9, through the leveling barrel into the threaded insert of the projector. Do not tighten the mounting hardware at this time. Step 3 Raise or lower each of the mounting legs, by rotating the leveling barrels, until all of the mounting legs are at an equal height. • Lower the mounting leg by rotating the leveling barrel counter-clockwise.
SPI-EXT Attaching the Projector Plate (cont’d) Step 5 ➊➊ Verify that the mounting legs are at an equal height. ➋➋ Return to Step 3 if they are not at an equal height or the SpiroLock™ Projector Plate is not level. Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the SpiroLock™ Projector Plate. If the M6 square nut is not aligned with any slot, you can use any thin implement, such as a toothpick, to nudge it into alignment.
SPI-EXT Attaching the Projector Plate (cont’d) Single Mounting Point Installation A single ¼-20 x 5/16″ screw must be used to attach the SpiroLock™ Projector Plate to the projector if your projector has only one mounting point. Do not overtighten the ¼-20 x 5/16″ screw. Proceed to the “Attaching the Projector to the Mount” section. Attaching the Projector to the Mount Step 1 The two (2) SpiroLock™ alignment notches must be aligned with the two (2) spindle alignment tabs.
SPI-EXT Attaching the Projector to the Mount (cont’d) Step 3 Tighten the M4 x 12mm Lock-It™ screw in the SpiroLock™ collar assembly. Proceed to the “Alignment & Fine-Tuning” section. Projector not shown for clarity. Alignment & Fine-Tuning ➊➊ Adjust the pitch, roll, and yaw of the projector up to 6° by firmly grasping the projector with both hands and slowly ➋➋ ➌➌ tilting it forward, backward, and side-to-side.
SPI-EXT Removing the Projector Your SpiroLock™ projector mount is designed to be quickly removed should your projector need service. If your projector is heavy and/or bulky, two people may be required to safely attach your projector to the SpiroLock™ Ceiling Plate. If your projector is to be mounted higher than shoulder height, you may need to use one or more ladders to safely attach your projector to the SpiroLock™ Ceiling Plate.
SPI-EXT Installing the Lock-It™ Security Barrel Install the security barrel to help lock the projector plate to the projector: ➊➊ Determine which leveling barrel will be removed. ➋➋ Remove the mounting screw. ➌➌ Remove the leveling barrel by turning the leveling ➍➍ ➎➎ ➏➏ barrel counter-clockwise. Thread in the security barrel clockwise. Insert and tighten the mounting screw. Attach a theft deterrent device (PCB-CSL1 or padlock) through the hole that is on the security barrel.
SPI-EXT Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
