2.4 cu. ft. DE 2.4 cu.ft.
Contents 1. SAFETY WARNINGS ............................................................................................... 2 2. INSTALLATION ......................................................................................................... 3 2.1 Location ................................................................................................................... 3 2.2 Reversing the Door Swing ............................................................................... 3 2.
1. SAFETY WARNINGS Caution: risk of fire 1) WARNING―Keep ventilation openings in the appliance enclosure or in the built-in structure, clear of obstruction. 2) WARNING―Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. 3) WARNING―Do not damage the refrigerant circuit. 4) WARNING―Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE PERSONNEL TO CARRY OUT SERVICING OR REPAIRS WHICH INVOLVE THE REMOVAL OF COVERS. TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS YOURSELF. 2. INSTALLATION 2.1 Location When selecting a position for your unit, you should make sure the floor is flat and firm, and the room is well ventilated with an average room temperature of between 16oC and 38oC. Avoid locating your unit near a heat source, e.g. cooker, boiler or radiator.
1) Remove the plastic covering from the top door hinge. 2) Unscrew the three screws from the bottom bracket. Remove the foot from opposite side. 3) Place to one side. 4) Slide the appliance door down about 15cm and off the top hinge pin and lift away from the appliance. 5) Remove the two screws from top bracket and replace on the other side. You will need to first remove the plastic caps from the other side. 6) Slide the appliance door back on to the Top hinge, making sure it’s the right way up.
2.3 Door Space Requirements D The unit's door must be able to open fully as shown. W×D≥880mm×800mm W 2.4 Leveling the Unit To do this, adjust the two leveling feet at the front of the unit. If the unit is not level, the door and magnetic seal alignments will not be covered properly. 2.5 Cleaning Before Use Wipe the inside of the unit with a mild solution of bicarbonate soda. Then rinse with warm water using a soft sponge or cloth.
Please do the same in reverse to insert the shelf at a different height. In order to make the most of the volume of the fresh food storage compartment and frozen-food storage compartment, the user can remove one or more shelves, drawers, out of the appliance, according to your daily use. 3. PRODUCT OVERVIEW Small door Thermostat Pan,drain Steel wire shelf Wire steel bar Leveler ,leg *All images in this instructions manual are for information only; please refer to your individual unit for details. 4.
perfectly normal, but you should be aware of them! These noises are caused by the circulation of the refrigerant liquid in the cooling system. It has become more pronounced since the introduction of CFC free gases. This is not a fault and will not affect the performance of your unit. This is the compressor motor working, as it pumps the refrigerant around the system. 4.3 Tips for Keeping Food in the Unit ◆ Cooked meat/fish should always be stored on a shelf above raw meat/fish to avoid bacterial transfer.
6. MAINTENANCE 6.1 Changing the Internal Light Lamp replacement must be done by professionals. 6.2 Care When Handling / Moving Your Unit Hold the unit around its sides or base when moving it. Under no circumstances should it be lifted by holding the edges of the top surface. 6.3 Servicing The unit should be serviced by authorized and qualified personnel and only genuine spare parts should be used. Under no circumstances should you attempt to repair the unit yourself.
Loud noises Whether the food is leveled, whether the refrigerator is balanced; Whether the refrigerator parts are properly placed. 7.1 Warm tips: ◆ The refrigerator enclosure may release heat during operation especially during the summer; this is caused by radiation of the condenser, and it is a normal phenomenon.
◆ Organize and label foods to reduce door openings and extended searches. Remove as many items as needed at one time, and close the door as soon as possible. 9. DISPOSAL Old units still have some residual value. An environmentally friendly method of disposal will ensure that valuable raw materials can be recovered and used again. The refrigerant used in your unit and insulation materials require special disposal procedures.
Contenido 1. ADVERTENCIAS DE SEGURIDAD .................................................................... 12 2. INSTALACION ......................................................................................................... 13 2.1 Ubicación............................................................................................................... 13 2.2 Invirtiendo la Apertura de la Puerta........................................................... 13 2.
1. ADVERTENCIAS DE SEGURIDAD Cuidado: riesgo de fuego 1) ADVERTENCIA― Mantenga las aberturas de ventilación del equipo libres de obstrucción. 2) ADVERTENCIA― No utilice dispositivos mecánicos u otros medios diferentes a los recomendados por el fabricante para acelerar el proceso de descongelación. 3) ADVERTENCIA― Tenga cuidado de no dañar el circuito refrigerante.
ES PELIGROSO REALIZAR MANTENIMIENTO O REPARACIONES QUE IMPLICAN LA ELIMINACIÓN DE LAS TAPAS PARA CUALQUIERA QUE NO SEA PERSONAL DE SERVICIO AUTORIZADO. NO INTENTE REPARAR USTED MISMO PARA EVITAR RIESGO DE UN CHOQUE ELÉCTRICO. 2. INSTALACION 2.1 Ubicación Cuando seleccione la ubicación para su unidad, debe asegurarse de que el piso esté plano y firme y la habitación esté bien ventilada con una temperatura promedio de entre 16oC y 38oC.
◆ Todas las piezas desmontadas deben guardarse para hacer la reinstalación de la puerta. ◆ No coloque la unidad horizontalmente ya que esto podrí a dañar el sistema de enfriamiento. ◆ Se recomienda que dos personas manipulen la unidad durante el montaje. 1) Retire la cubierta de plástico de la bisagra superior de la puerta. 2) Afloje los tres tornillos de la arandela inferior. Quite el pie del lado opuesto. 3) Coloque a un lado.
7) Compruebe que la puerta estéalineada horizontalmente y verticalmente y que los sellos están cerrados por todos lados antes de finalmente apretar la bisagra inferior y nivelar los pies como sea necesario. 2.3 Requerimientos de Espacio de la Puerta D La puerta de la unidad debe ser capaz de abrir completamente como se muestra. W×D≥880mm×800mm W 2.4 Nivelando la Unidad Para nivelar la unidad, ajuste las dos patas de nivelación en la parte delantera de la unidad.
suministrado con la unidad. ◆ Antes de Encender! No encienda hasta dos horas después de mover la unidad. El líquido refrigerante necesita tiempo para asentarse. 2.7 Accesorios Interiores Su electrodomestico incluye varios estantes plasticos o de vidrio para almacenamiento - diferentes modelos tienen diferentes combinaciones.
Posición “Off”:Unidad apagada Posición “Min”:Temperatura menos frí a Posición “Med”: Operación Normal (adecuada a casi todas las ocasiones) Posición “Max”:Temperatura mas frí a ◆Para altas temperaturas ambientales, por ejemplo en dí as calurosos de verano, puede ser necesario ajustar el termostato a la posición más frí a (posición "Max"). Esto puede causar que el compresor funcione continuamente para mantener una temperatura baja en el interior del gabinete.
5. LIMPIEZA 5.1 Descongelando la escarcha Se puede acumular escarcha en la superficie interna de la parte posterior del aparato; Esta escarcha se descongela automáticamente durante el ciclo de apagado del compresor. El agua es canalizada a través del orificio de desagüe a la bandeja de recogida sobre el compresor donde se evaporará. Asegúrese de que el orificio de drenaje se revisa y se limpia regularmente para evitar que el agua se acumule y llegue al compartimiento de almacenaje. 5.
limpie el aparato y deje la puerta entreabierta para evitar olores desagradables. 7. Resolución de Problemas Los siguientes problemas simples pueden ser resueltos por el usuario. Por favor llame al departamento de servicio post-venta si no se resuelven los problemas. Problema Que verificar Si el refrigerador estáenchufado y conectado a la corriente eléctrica; Aparato no funciona Baja corriente electrica; Falla eléctrica o problema en el circuito.
Este es un fenómeno normal y la condensación puede secarse con una toalla seca. ◆ Zumbido: Un zumbido es generado por el compresor cuando esta funcionando, especialmente al arrancar o apagarse. 8. RECOMENDACIONES PARA EL AHORRO DE ENERGIA No abra la puerta demasiado a menudo, especialmente cuando el clima es húmedo y caliente. Una vez que usted abra la puerta, cierrela tan pronto como sea posible.
ecológico de eliminación aseguraráque valiosas materias primas puedan ser recuperadas y reutilizadas. El refrigerante y los materiales aislamiento usados en su unidad requieren procedimientos especiales de eliminación. Asegúrese de que ninguno de los tubos en la parte posterior de la unidad estádañado antes de la eliminación. Busque información actualizada sobre las opciones para deshacerse de su unidad antigua y del material de emapque de la nueva en la oficina del consejo local.