24” Wide Large Storage Cabinet DATE STAMP Assembly Instructions Model # GSCW-0706-2K 2 Person Installation Required CONTACT US FIRST parts@prepacmfg.com 1-877-PREPAC1 1-877-773-7221 Mon - Fri • • 7am - 4pm PST 10am - 7pm EST For help with assembly If you have received a damaged or defective part or are missing hardware. We will process replacement parts in 2 business days or less. Parts are shipped via UPS Ground or mail.
Cabinet Parts C1 Top (1) Dessus TP-10051-G gray / gris C1 C2 Gable (1) Pignon GA-10055-G gray / gris C4 C3 C2 Left Side (1) Côté gauche SL-10054-G gray / gris C4 Right Side (1) Côté droit SR-10054-G gray / gris C5 C5 C3 Fixed Shelf (1) étagère fixe SH-10053-G gray / gris C6 C6 Adjustable Shelves (3) étagère ajustable SF-10038-G gray / gris C6 C7 Bottom Stabilizer (1) Renforcement inférieur ST-10065-G gray / gris C6 C8 Bottom Shelf (1) étagère inférieure BT-10041-G gray / gris C7 C9 C8 C9
AVANT DE COMMENCER BEFORE YOU BEGIN Identifier toutes les pièces et le matériel afin de s’assurer que tout est inclus. Identify ALL parts and hardware to ensure everything is included.
1a Attach Rail Hooks to the Gable (C2) as shown. Use wrench to tighten nuts. Fixez les crochets de suspension au pignon (C2) comme montre.
2a Attach Rail Hooks to the Left (C3) & Right (C4) Sides as you did in Step 1. Use wrench to tighten nuts Fixez les crochets de suspension ������������������������������������������������� aux côtés gauche (C4) et droite (C5) comme étape 1.
3 Insert cams into the Fixed Shelf (C5), then attach to Left (C3) and Right (C4) Sides and tighten cams. Insérez des cames dans l’étagère fixe (C5), puis attachez aux côtés gauche (C4) et (C5) droit. Serrez les cames. C4 C5 C3 Insert cams with the opening facing toward the hole for the twister dowel. Insérez les cames dans l’ouverture faisant face au trou du goujon à visser.
4a Attach Top (C1) to Left (C3) and Right (C4) Sides and Gable (C2) with Confirmat Screws Fixez le dessus aux côtés gauche (C3) et droite (C4) et au pignon (C2) avec les Vis Confirmat Confirmat Screw Vis Confirmat C4 C1 C2 C3 4b Attach Bottom Stabilizer (C7) to Left (C3) and Right (C4) Sides with Confirmat Screws Fixez le renforcement inferière aux côtés gauche (C3) et droit (C4) avec les Vis Confirmat C4 C3 C7 Confirmat Screw Vis Confirmat Page of 20
5a Attach Bottom Shelf (C8) to Left (C3) and Right (C4) Sides with Confirmat Screws Fixez l’étagère inférieure (C8) au côtés gauche (C3) et droit (C4) avec vis Confirmat Confirmat Screw Vis Confirmat C4 C3 5b Attach hinges to doors (C9) with screws provided Fixez les charnières de portes (C9) avec vis fournies C8 #6 - 5/8” Wood Screws Vis de bois no. 6 5/8 po. C9 5c Attach handles to doors (C9) with screws provided. Do not attach doors to cabinets yet.
Installing Hang Ups Garage Cabinets 2 people required Read through all installation steps before beginning ONLINE HELP Pour suspendre les armoire au mur, vous aurez besoin de 2 personnes Lisez bien toutes les étapes de cette installation avant d’entamer la tâche. L’AIDE EN LIGNE To see a how-to installation video, click on “How to Install Prepac’s Garage Storage Collection” on the Assembly page in the Support section of our website: www.prepacmfg.
Hanging a Single 24” Cabinet Accrocher une seule armoire 24 po. If you are installing one cabinet only: Si vous installez un cabinet uniquement : A) Center the rail and the cabinet across 3 studs (this will leave excess rail on either side) A) Du centre du rail et de l’ensemble du cabinet 3 goujons (ce qui laissera l’excès rail de chaque côté) B) Align the cabinet so that the rail is flush with one side of the cabinet. You MUST mount to 2 studs.
Hanging Multiple Cabinets Pour suspendre plusieurs armoires We will illustrate how hang multiple cabinets using the sample configuration below. Nous allons illustrer comment accrocher plusieurs armoires à partir de l’exemple de configuration ci-dessous. 1. On your wall, mark where the cabinets will be positioned with tape or a pencil 2. Determine the number of Metal Rails and Connecting Braces needed. You may not need all rails 3.
The illustration below shows where the Metal Rails & Connecting Braces should be attached to the wood studs for this configuration L’illustration ci-dessous montre où les rails métalliques & la connexion les accolades ne doivent être connectés au bois goujons pour cette configuration NOTE: Rails and Braces are shown ABOVE cabinets for clarity REMARQUE : Les rails et les accolades sont indiqués ci-dessus les armoires pour plus de clarté 1/8” 1/8” 1/8” For the Base Cabinets, cut BOTH METAL RAILS.
Installing Hang Ups Garage Cabinets Installation “Hang Ups” Garage armoires 1 Measure 79½ inches from the floor and make multiple marks along the wall Mesurer 79½ pouces du sol et faire plusieurs repères le long du mur 79½” 2 With a level, connect the marks Avec un niveau, connectez les marques Page 13 of 20
3a Find the center of the wall studs and mark the location of each stud along the line. Studs are typically 16 inches apart center to center. Trouver le centre du mur et marquer l’emplacement de chaque goujon le long de la ligne. Les goujons sont généralement de 16 centimètres l’un de l’autre centre à centre. 3b Using a 3/16th inch drill bit, pre-drill holes 3 inches deep at the locations you had marked.
4 Hang the First Rail Accrocher la première position de Rail Position the Metal Rail over the pre-drilled holes and insert wood screws into the first & second holes. Tighten screws with the Allen Key provided. Positionnez la piste de métal sur les trous pré-percés et insérez les vis à bois dans le premier & deuxième trous. Serrer les vis avec la clef Allen fournie.
6 Hanging the Second Rail Accrocher le deuxième position de Rail Slide the second Metal Rail BEHIND the Connecting Brace Faites glisser le Rail Métallique deuxième derrière le connectant le renfort Secure the Connecting Brace to the Second Rail Sécuriser la connexion renfort pour le deuxième rail Page 16 of 20
7 Carefully hang the cabinet onto the Metal Rail until it locks into place. Laisser pendre soigneusement le cabinet sur la rail métallique jusqu’à ce qu’elle se verrouille en place. Make sure the Rail Hook slides fully into the notch on the Metail Rail Track. Assurez-vous que le crochet de Rail de diapositives pleinement dans l’encoche du Metail voies de chemin de fer.
8 Insert metal dowel pins and add adjustable shelves Insérer les Goujons de métal et ajouter étagères ajustable 9 Attach doors Fixez les portes Page 18 of 20
Hinge Adjustments Hinges are 6-way adjustable, allowing you to make precise adjustments. Ajustements de charnière Les charnières sont 6-voies réglables, vous permettant d’effectuer des réglages précis. Vertical Door Alignment: Loosen the top & bottom Hinge Plate Screws (on both hinge sets) and move the door up or down. Alignement de la porte verticale: desserrer le haut & bas plaque charnière vis (sur les deux charnières) et déplacer la porte vers le haut ou vers le bas.
Give Us Your Feedback CALL US 1-877-PREPAC1 (1-877-773-7221) Mon - Fri 7am - 4pm PST 10am - 7pm EST Email Us: assembly@prepacmfg.com Thanks! Faites-nous part de vos commentaires Écrivez-nous à : assembly@prepacmfg.