PRESIDENT HR2600 10 Meter Amateur Mobile Transceiver Doc’s Electronics http://hr2510.homeip.net:2510/ Doc’s Electronics http://hr2510.homeip.
Contents Welcome! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Front Panel Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CTCSS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting & Using CTCSS . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welcome! NOTES/MEMOS To the world of 10 Meter amateur radio communications! You have purchased what we feel to be the finest 10 Meter mobile transceiver available. Your HR 2600 has been designed using the latest state of the art electronics to give you years of trouble free service. To get the most from your HR 2600, please read this operating guide thoroughly. WARNING: To operate this transceiver, you MUST have an FCC Radio Amateur Operator’s license.
Controls and Functions 1. Mode Switch - This control is used to select the desired transmit mode. The modes available are: CW, LSB, USB, AM, and FM. 2. SWR/CAL Control - This control is used to adjust the calibration of the SWR meter while in SWR CAL mode. 3. RIT Control - The Receiver Incremental Tuning control is used to fine tune the received signal. This is used in USB and LSB modes to obtain maximum clarity of reception, and in CW mode to control the pitch of the beat note.
Amateur Radio Operation - continued Eventually, you’ll probably want to get another, higher class of amateur license, with more privileges. Exams for Technician, General, Advanced, and Extra Class licenses are given by three-member Volunteer Examiner Teams. Hundreds of exam sessions are held across the country every month, most on weekends. (You can take the Novice exam from a Volunteer Examiner Team, too, if it’s more convenient.
Controls and Functions - continued 20. Multifunction Meter - This meter can display S/RF, Modulation, SWR Cal, or SWR. See item (8), Meter Switch and the operation section for more information. 21. Frequency Display - The Frequency Display displays the currently selected transmit and receive frequency. 22. Meter Mode Display - Displays the currently selected meter operating mode. 23. Band Segment Display - Shows the currently selected band segment. 24.
Troubleshooting Front Panel Connector If your HR 2600 is not performing up to your expectations, please try these simple steps. If you still cannot get satisfactory results after reading this manual and following the troubleshooting steps, please contact Uniden Customer Service at: (317) 842-2483. Trouble Unit will not turn on No Power Check 1. Check power cord and all connections. 2. Check power cord fuse. 3.. Check vehicle electrical system Channel Up 3 4 2 Channel Down 5 Transmit (PTT) 1 4.
CTCSS Control Specifications Setting & Using CTCSS The HR 2600 has a built-in CTCSS encoding (Continuous Tone Coded Squelch System) for accessing repeaters. CTCSS is activated only in FM RPT mode of operation. To set the CTCSS frequency, proceed as follows: 1. Place the unit top down on a non-scratching surface. 2. Remove the cover screws for the bottom half of the case (see photo above). Use caution when removing the bottom half of the case, since the speaker is connected to the main board.
Operation - continued SWR Meter After you have calibrated the SWR Meter according to the SWR CAL procedure previously shown, you are ready to proceed to check the SWR of your HR 2600 and antenna. Press the Meter button until “SWR” is displayed above the meter (once after completing the SWR CAL procedure). At this point, pressing the PTT switch on the microphone if in AM or FM mode, or pressing the CW key if in CW mode will transmit a signal. As you transmit, your SWR will be displayed on the meter.
Rear Panel Connectors 1 2 3 4 5 6 7 8 9 Accessory Connector Operation - continued Multifunction Meter The Multifunction Meter built in to your HR 2600 provides a number of useful functions. These are: S/RF Meter MOD Meter SWR CAL Meter SWR Meter Every time you press the Meter button, the next function will be selected. When you reach the end of the functions, it will start over with the first. When in receive mode, the meter is always in the “S” function. (Received signal strength.
Operation - continued Rear Panel Connectors - continued CW Operation Using CW mode with the HR 2600 is easy. Just select your operating frequency, place the mode switch in CW, and you’re ready to transmit CW if you have connected an external key to the accessory plug on the rear of the unit. (See the section on rear panel connectors for information on connecting a CW key.
Installation Transceiver Mounting Plan the location of the transceiver and microphone bracket before starting the installation. Select a location that is convenient for operation and does not interfere with the driver or passenger in the vehicle. The radio should be secured to a solid surface, using the mounting bracket and self-tapping screws supplied. Mobile Antenna The antenna is a very important factor affecting transmission and reception.