Operation Manual

31
B) HOW TO USE YOUR TRANSCEIVER
1) ON/OFF ~ VOLUME
Turn on radio: clockwise turn VOLUME knob (1) until radio emit beep and show
current channel, radio is on. Turn Off radio: counterclockwise turn VOLUME
knob (1)until radio emit click sound ,then radio is off.
Volume Adjustment: Radio is on, rotate VOLUME knob (1) to adjust volume.
LCD shows “UOLXX” for 5 seconds which means volume level. Total is 36 levels.
Clockwise to increase volume. Counterclockwise to decrease volume.
2) RF POWER
In TX, rotate RF PWR knob (2) to adjust FM/AM/USB/LSB output power. Clock-
wise to increase power. Counterclockwise to decrease power.
3) ASC (Automatic Squelch Control) ~ SQUELCH
Suppresses undesirable background noises when there is no communication.
Squelch does not affect neither sound nor transmission power, but allows a
considerable improvement in listening comfort.
a) ASC: AUTOMATIC SQUELCH CONTROL
Worldwide patent, a PRESIDENT exclusivity.
Turn the SQUELCH knob (3) anti-clockwise into ASC position. “ASC” appears
on the LCD. No repetitive manual adjustment and a permanent improve-
ment between the sensitivity and the listening comfort when ASC is active.
This function can be disconnected by turning the switch clockwise. In this
case the squelch adjustment becomes manual again. “ASC” disappears
from the LCD, “SQL on” appears for 5 seconds.
b) MANUAL SQUELCH
Turn the SQUELCH knob clockwise to the exact point where all background
noise disappears. This adjustment should be done with precision as, if set to
maximum (fully clockwise), only the strongest signals will be received. LCD shows
“SQLXX” for 5 seconds which means squelch volume level. Total is 36 levels.
4) MENU
Press the MENU key (4) for 2 seconds to enter in the menu function setting.
“FUNC” appears on the LCD.
Use s/t keys (10) to select the desired function.
Use rotary PUSH knob (6) to set the function.
Press any key except PUSH knob (6) or wait for 5 seconds to store and exit.
“FUNC” disappears from the LCD.
See § MENU FUNCTIONS for details, page 35.
5) MEM ~ STORE
MEM
(short press)
Press MEM key (5) to enter into Memory Mode.
Press s/t keys (10) on to select the pre-stored channel (6 memories).
Press MEM key (5) again to exit Memory Mode.
STORE (long press)
Select desired channel, band and modulation mode.
Long press MEM-STORE key (5) to enter into Channel Storage Setting, memory
blinks in the LCD.
Rotate PUSH knob (6) to select the storage memory n1 ~ n6.
Long press MEM-STORE key (5) until blinking memory disappeared. Storage
finished and exit Channel Storage Setting.
6) ROTARY “PUSH” KNOB
In POWER ON status, rotate PUSH knob (6) to adjust frequency. Clockwise
to increase, counterclockwise to decrease.
Press PUSH knob (6), “-”displayed under frequency which means adjust
frequency’s stepping.
Push or rotate the PUSH knob (6) is also used to set functions or parameters.
7) CLARIFIER
This CLARIFIER knob (7), allows a frequency deviation during reception in
order to improve the clearness of your correspondent’s voice.
8) MIC GAIN
In POWER ON status, rotate MIC GAIN knob (8) to adjust microphone gain.
LCD shows “nIC XX” for 5 seconds which means microphone gain level. Total
is 36 levels Clockwise to increase, counterclockwise to decrease.
In PA status, rotate MIC GAIN knob (8) to adjust volume. LCD shows
“nIC XX” for 5 seconds which means microphone volume level. Total is 36
levels. Clockwise to increase, counterclockwise to decrease.
9) RF GAIN
In RX, rotate RF GAIN knob (9) to adjust RX gain. Clockwise to increase,
counterclockwise to decrease.
10) s/t CHANNEL/FREQUENCY SELECTOR
s/t keys (10) allows increasing or decreasing a channel number or a
frequency number according the choose done in the [UP dn] menu (see §
s/t KEYS SETTING, page 36).
English