Operation Manual

34
In “
” mode:
- store the CTCSS tone or DCS code. The blinking stops.
In “
” mode:
- store the CTCSS tone or DCS code of the reception (RX).
- “TX” blinks in addition to the selected data.
- Rotate PUSH knob (6) to set desired CTCSS tone or DCS code of the transmis-
sion (TX).
- Press MEM-STORE key (5) for 2 seconds to store the CTCSS tone or DCS code
of the transmission (TX). The blinking stops.
- Long press MODE-CTCSS/DCS key (18) to disable CTCSS tone or DCS code.
See tables on page 52.
19) VOX ~ VOX SET
VOX
(short press)
The VOX function allows transmitting by speaking into the original microphone
(or in the optional vox microphone) without pressing the PTT pedal (23). In
case of the use of an optional vox mike connected to the rear panel of the
radio - VOX MIC jack (E), the original microphone doesn’t work.
Press the VOX key (19) in order to activate the VOX function. “VOX” is displayed
on the LCD. A new pressure on the VOX key (19) switches the function off.
“VOX”disappears from the LCD.
VOX SET (long press)
Press for 2 second the VOX-VOX SET key (19) in order to activate the VOX SET
function (if the VOX function is off, this will turn the function on and display
“VOX” on the LCD). “ ” appears on the LCD.
Three features are possible: Sensitivity level, Anti-Vox level and Vox Delay
time.
Press s/t keys (10) in order to select to the following feature. LCD shows the
feature.
Rotate PUSH (6) to set the feature.
Press MEM/STORE key (5) to store and skip into the next feature.
Once the adjustments are done, press the VOX-VOX SET key (19) in order
to quit the VOX SET function. If any adjustment have been done during 5
seconds, the transceiver will quit the VOX SET function automatically.
- Sensitivity “
”: allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from 1
(high sensibility) to 9 (low sensibility). Default: 5.
- Anti-Vox “ ”: allows disabling the transmission generated by the surround-
ing noise. The level is adjustable: 0 (OFF), from1 (high level) to 9 (low level).
Default: 9.
- Delay Time “
”: allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1 (short
time delay) to 9 (long time delay). Default:1.
20) SPLIT ~ SPLIT SET
SPLIT
(short press)
The SPLIT function allows to transmit and receive on separated frequencies.
Press SPLIT key (20) to enable repeater function, LCD shows “ ” for 5
seconds.
Press SPLIT key again to disable repeater function, LCD shows “
” for
5 seconds.
Note: Channel, Band and Frequency are blinking if the SPLIT function is active.
SPLIT SET (long press)
Long press SPLIT-SPLIT SET key (20) to set repeater’s OFFSET and DIRECTION
Press s/t (10) to alternate between FREQUENCY OFFSET and DIRECTION in
the menu list.
Rotate PUSH (6) knob to set desired feature.
Press MEM/STORE key (5) for 2 seconds to store and skip into next menu.
Press SPLIT key (20) or wait for 5 seconds to exit SPLIT SET function.
- FREQUENCY OFFSET: frequency blinks on the LCD.
- DIRECTION: LCD shows “SPLiT”.“
” in LCD means positive offset set in cur-
rent channel, “ ” means negative offset set in current channel.
21) BAND ~ +10KHz
BAND
(short press)
Press BAND key (21) for quick movement skipping 200 kHz in A ~ B ~ C ~ D ~ E
~ F ~ 9 ~ H ~ I segments.
+10KHz (long press)
Long press BAND-+10KHz key (21) to enable frequency +10KHZ. LCD shows
“10K ”
Long press BAND-+10KHz key (21) again to disable frequency +10KHZ. “10K”
disappears from the LCD.
22) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the set-
ting of the equipment into the dashboard easier.
See Cabling Diagram page 52.
English