User Manual
Table Of Contents
- 1 Overview
- 1.1 Introduction
- 1.2 Product Registration
- 1.3 What’s in the box
- 1.4 What’s in your MyPreSonus account
- 1.5 Companion PreSonus Products
- 1.6 Firmware Updates
- 2 Standard Controller Mode
- 2.1 Setup Mode
- 2.2 Pads
- 2.2.1 RGB Colors
- 2.2.2 Triggering Notes
- 2.2.3 Plus and Minus Pads
- 2.3 Touch Strip
- 2.4 A-H Buttons
- 2.5 Knobs 1-8
- 2.6 Navigation Buttons
- 2.7 Transport Buttons
- 2.8 Screen Controls
- 2.8.1 Instrument Mode
- 2.8.2 Song Mode
- 2.8.3 Editor Modes
- 2.8.4 User Mode
- 3 Advanced Studio One Integration
- 3.1 Controls
- 3.1.1 Pad Controllers
- 3.1.2 Touch Strip
- 3.1.3 A-H Buttons
- 3.1.4 Encoders
- 3.1.5 Navigation Buttons
- 3.1.6 Transport Buttons
- 3.1.7 Global Controls
- 3.2 Screen Controls
- 3.2.1 Instrument Mode
- 3.2.2 Song Mode
- 3.2.3 Editor Modes
- 3.2.4 User Mode
- 4 Advanced Ableton Live Integration
- 4.1 Control Functions
- 4.1.1 RGB Colors
- 4.1.2 Triggering Notes or Clips
- 4.1.3 Plus and Minus Pads
- 4.1.4 Touch Strip
- 4.1.5 A-H Buttons
- 4.1.6 Knobs 1-8
- 4.1.7 Navigation Buttons
- 4.1.8 Transport Buttons
- 4.2 Screen Controls
- 4.2.1 Instrument Mode
- 4.2.2 Song Mode
- 4.2.3 Editor Mode
- 4.2.4 User Mode
- 5 Studio One Artist Quick Start
- 5.1 Installation and Authorization
- 5.2 Setting Up Studio One
- 5.2.1 Configuring Audio Devices
- 5.2.2 Configuring MIDI Devices
- 5.3 Creating a New Song
- 5.3.1 Configuring Your Audio I/O
- 5.3.2 Creating Audio and Instrument Tracks
- 5.3.3 Recording an Audio Track
- 5.3.4 Adding Virtual Instruments and Effects
13
2 Standard Controller Mode
2.8 Screen Controls
ATOM SQ
Owner’s Manual
2.8.4 User Mode
Touch
CC
+/-
Pitch
Page 1
Knob
Page 1
Button
1 2
3 4
1. Touch Strip. When selected, the Screen Encoder will
change how the touch strip behaves:
• Range. Touching and sliding will change the viewable range in Key
mode or change transposition in Blocks or Continuous modes.
• Mod. Touching and sliding will control Mod Wheel messages
from from minimum (left) to maximum (right).
• Pitch. Touching and sliding will control Pitch Bend messages.
While active, pitch always resets to center.
• CC. Touching and sliding will control the CC message sent
via the strip from minimum (left) to maximum (right).
• Arp. the touch strip will use the 8 divisions (tall white lines) to
change the arpeggiator’s rate. From left to right: 1/4, 1/8, 1/16,
1/32, 1/4T, 1/8T, 1/16T, 1/32T. In this mode, all red LEDs will
remain off indicating that the Touch Strip is controlling rate.
2. +/-. When selected, the Screen Encoder will change
how the + and - buttons behave:
• Pitch. The plus and minus buttons control pitch bend using
pressure. The Plus button sends pitch up and the Minus button
sends pitch down. Releasing a button will reset back to center.
• Octave. The plus and minus buttons will cycle up
(plus) or down (minus) through octaves.
3. Knob. When selected, the Screen Encoder will change the
MIDI assignments for Knobs 1-8 (4 pages/banks total).
4. Button. When selected, the Screen Encoder will change the assignments
for the A-H buttons MIDI messages (2 pages/banks total).