User Manual
Table Of Contents
- 1 Overview
- 1.1 Introduction
- 1.2 About This Manual
- 1.3 Summary of StudioLive 16.0.2 Hardware Features
- 1.4 What is in the Box
- 1.5 What is in Your My PreSonus account
- 2 Getting Started
- 2.1 Level Setting Procedure
- 3 Hookup
- 3.1 Rear-Panel Connections
- 3.2 Typical Basic Band Hookup Diagram
- 3.3 Business Conference Hookup Diagram
- 4 The Fat Channel
- 4.1 The Select Button
- 4.2 Input Controls
- 4.3 Dynamics Processing and EQ
- 4.3.1 Fat Channel Processing Guide
- 4.3.2 High Pass Filter
- 4.3.3 Gate
- 4.3.4 Compressor and Limiter
- 4.3.5 Equalizer
- 4.3.6 Dig Out: Recording EQ and Dynamics
- 4.4 Fat Channel Presets: Copy, Paste, Load
- 4.4.1 Copying and Pasting
- 4.4.2 Loading Fat Channel Presets
- 4.4.3 Saving Fat Channel Presets
- 4.4.4 Channel Presets Library
- 4.5 Metering
- 4.5.1 StudioLive Metering Controls
- 5 Basic Controls
- 5.1 Input Channel Controls
- 5.2 Aux and FX Buses
- 5.2.1 Analog Aux Bus Controls
- 5.2.2 Internal FX Bus Controls
- 5.2.3 Aux and FX Bus Channel Sends
- 5.2.4 Creating Monitor Mixes
- 5.2.5 Creating Internal FX Mixes
- 5.3 MultiModes
- 5.3.1 USB Return Mode.
- 5.3.2 Solo Mode
- 5.3.3 Mute Button
- 5.4 Main Output Bus
- 5.5 Talkback System
- 5.6 Solo Bus
- 5.6.1 Using the Solo Bus for Monitoring
- 5.6.2 Using Solo in Place (SIP) to Set Up a Mix
- 5.7 Monitor Bus
- 6 Digital Effects | Master Control
- 6.1 The Digital FX (Effects) Menu
- 6.1.1 Creating FX Presets
- 6.1.2 Reverb and its Parameters
- 6.1.3 Delay and its Parameters
- 6.1.4 Digital Effects Preset Library
- 6.1.5 Digital Effects Types
- 6.2 Scenes
- 6.2.1 S1: Zero Out (Board Reset)
- 6.2.2 Creating a Scene
- 6.2.3 Scene Recall
- 6.2.4 Fader Locate
- 6.2.5 AutoStore
- 6.3 Graphic Equalizer
- 6.3.1 The Graphic EQ Menu and Controls
- 6.3.2 Saving and Loading GEQ Presets
- 6.4 System Menu
- 6.4.1 LCD Contrast and LCD Backlight
- 6.4.2 Aux Send Position
- 6.4.3 MIDI Control Mode
- 6.4.4 Lockout Mode
- 6.4.5 Firmware Version
- 6.5 Using MIDI Control Mode to Remote-Control StudioLive
- 6.5.1 Understanding MIDI
- 6.5.2 Recalling Scenes and FX Presets Remotely
- 6.5.3 Using Control Change Messages to Control Volume and FX Assignments
- 6.5.4 Controlling the StudioLive 16.0.2 with a Behringer FCB1010
- 6.5.5 Controlling the StudioLive 16.0.2 with a Roland FC-300
- 7 Resources
- 7.1 Stereo Microphone Placement
- 7.2 EQ Frequency Guides
- 7.3 Technical Specifications
- 7.4 StudioLive 16.0.2 Block Diagram
- 7.5 StudioLive 16.0.2 Recall Sheet
- 8 Troubleshooting and Warranty
- 8.1 Troubleshooting
- 8.2 PreSonus Limited Warranty
38
6 Digital Effects | Master Control
6.1 The Digital FX (Effects) Menu
StudioLive™ 16.0.2 USB
Owner’s Manual
6 Digital Effects | Master Control
From the Digital Effects | Master Control section, you can select and
change the parameters of the two internal effects processors, and you
can store and recall every setting on the StudioLive. Because almost all
StudioLive features are controlled from the mixing surface (rather than
using menus and submenus), you will mainly use this section to adjust the
internal effects processors and to save and recall presets and Scenes.
Power User Tip: With all menus, the StudioLive remembers which page you were on
when you navigated away to another menu. To quickly jump to page 1, simply press the
menu’s button twice (e.g., to return to page 1 of the FX Menu, press the FX button twice).
6.1 The Digital FX (Effects) Menu
The StudioLive features two internal effects processors. Each processor can
access the StudioLive’s selection of high-quality reverbs and delays. Each of
these effect buses can be routed to the aux buses or the main outputs.
To access the effects library and make adjustments to effect parameters, press the FX
button in the Master Control section.
The first page of the FX menu is the QuickView screen. It displays both of the
effects assigned to the internal effects buses and the main parameter for each.
Effect A is assigned to EFX A bus, and Effect B is assigned to EFX B bus.
Use the Next and Prev buttons to navigate through the screen. To change
a parameter, use the Value encoder directly beneath the LCD screen. The
color will invert for each parameter when it is selected for modification.
4 The Next button will scroll through this screen in the following order: FX A library
selection, FX A main parameter, FX B library selection, FX B main parameter.
4 When choosing your effects preset, use the Value
encoder to scroll through the library.