User Manual
Table Of Contents
- 1 Overview
- 1.1 Introduction
- 1.2 About This Manual
- 1.3 Summary of StudioLive 16.0.2 Hardware Features
- 1.4 What is in the Box
- 1.5 What is in Your My PreSonus account
- 2 Getting Started
- 2.1 Level Setting Procedure
- 3 Hookup
- 3.1 Rear-Panel Connections
- 3.2 Typical Basic Band Hookup Diagram
- 3.3 Business Conference Hookup Diagram
- 4 The Fat Channel
- 4.1 The Select Button
- 4.2 Input Controls
- 4.3 Dynamics Processing and EQ
- 4.3.1 Fat Channel Processing Guide
- 4.3.2 High Pass Filter
- 4.3.3 Gate
- 4.3.4 Compressor and Limiter
- 4.3.5 Equalizer
- 4.3.6 Dig Out: Recording EQ and Dynamics
- 4.4 Fat Channel Presets: Copy, Paste, Load
- 4.4.1 Copying and Pasting
- 4.4.2 Loading Fat Channel Presets
- 4.4.3 Saving Fat Channel Presets
- 4.4.4 Channel Presets Library
- 4.5 Metering
- 4.5.1 StudioLive Metering Controls
- 5 Basic Controls
- 5.1 Input Channel Controls
- 5.2 Aux and FX Buses
- 5.2.1 Analog Aux Bus Controls
- 5.2.2 Internal FX Bus Controls
- 5.2.3 Aux and FX Bus Channel Sends
- 5.2.4 Creating Monitor Mixes
- 5.2.5 Creating Internal FX Mixes
- 5.3 MultiModes
- 5.3.1 USB Return Mode.
- 5.3.2 Solo Mode
- 5.3.3 Mute Button
- 5.4 Main Output Bus
- 5.5 Talkback System
- 5.6 Solo Bus
- 5.6.1 Using the Solo Bus for Monitoring
- 5.6.2 Using Solo in Place (SIP) to Set Up a Mix
- 5.7 Monitor Bus
- 6 Digital Effects | Master Control
- 6.1 The Digital FX (Effects) Menu
- 6.1.1 Creating FX Presets
- 6.1.2 Reverb and its Parameters
- 6.1.3 Delay and its Parameters
- 6.1.4 Digital Effects Preset Library
- 6.1.5 Digital Effects Types
- 6.2 Scenes
- 6.2.1 S1: Zero Out (Board Reset)
- 6.2.2 Creating a Scene
- 6.2.3 Scene Recall
- 6.2.4 Fader Locate
- 6.2.5 AutoStore
- 6.3 Graphic Equalizer
- 6.3.1 The Graphic EQ Menu and Controls
- 6.3.2 Saving and Loading GEQ Presets
- 6.4 System Menu
- 6.4.1 LCD Contrast and LCD Backlight
- 6.4.2 Aux Send Position
- 6.4.3 MIDI Control Mode
- 6.4.4 Lockout Mode
- 6.4.5 Firmware Version
- 6.5 Using MIDI Control Mode to Remote-Control StudioLive
- 6.5.1 Understanding MIDI
- 6.5.2 Recalling Scenes and FX Presets Remotely
- 6.5.3 Using Control Change Messages to Control Volume and FX Assignments
- 6.5.4 Controlling the StudioLive 16.0.2 with a Behringer FCB1010
- 6.5.5 Controlling the StudioLive 16.0.2 with a Roland FC-300
- 7 Resources
- 7.1 Stereo Microphone Placement
- 7.2 EQ Frequency Guides
- 7.3 Technical Specifications
- 7.4 StudioLive 16.0.2 Block Diagram
- 7.5 StudioLive 16.0.2 Recall Sheet
- 8 Troubleshooting and Warranty
- 8.1 Troubleshooting
- 8.2 PreSonus Limited Warranty
61
6 Digital Effects | Master Control
6.5 Using MIDI Control Mode to Remote-Control StudioLive
StudioLive™ 16.0.2 USB
Owner’s Manual
Naming and Saving Your Patch
1. Press the right Parameter button until the LCD reads “Patch Name.”
2. Use the Value Up and Down buttons and left/right Parameter
buttons to enter a name (such as “My Preset”).
3. Press the Exit button. You will now be on the Main screen of the LCD.
4. Press the Write button so that the LCD displays “Write to [WRITE] 01:”
5. In this example, we will save to patch-library position 01
but you can also use the Value buttons to scroll to an empty
patch position. Press the Write button again to store.
6. Press the Write button again to confirm.
Recalling StudioLive Scenes
Making sure the red LED is illuminated on the first row of pedals,
depress Pedal 1/6. You will see that Scene 2 has been recalled on your
StudioLive. You are now ready to control your StudioLive as follows:
4 CTL1: Recall Preset F10: Concrete Floors on FXA
4 CTL2: Assign/Unassign FXA to Main bus
4 Expression Pedal 1: FXA Output level
4 Expression Pedal 2: Main Output level