User Manual
Table Of Contents
- 1 Overview
- 1.1 Introduction
- 1.2 About This Manual
- 1.3 What is in the Box
- 1.4 What is in your My PreSonus Account
- 2 Getting Started
- 2.1 Level-Setting Procedure
- 3 Hookup
- 3.1 Connections and Controls
- 3.1.1 Inputs
- 3.1.2 Outputs
- 3.1.3 Rear Panel Connections
- 3.2 Channel Controls
- 3.2.1 Digital Returns
- 3.3 The Super Channel
- 3.3.1 Pairing a Bluetooth Device
- 3.4 Aux Buses
- 3.4.1 Monitor Bus Controls
- 3.4.2 Creating Monitor Mixes
- 3.5 Internal FX Bus
- 3.5.1 Effects Presets
- 3.5.2 Internal FX Bus Return
- 3.5.3 Creating Internal Effects Mixes
- 3.5.4 Using an External Effects Processor
- 3.6 Master Section Controls
- 3.6.1 Control Room Levels
- 3.7 Typical Band Setup Diagram
- 3.8 Typical Home Studio Setup Diagram
- 4 SD Recording and Playback
- 4.1 SD Recording
- 4.2 SD Playback
- 5 Connecting to a Computer
- 5.1 Installation for Windows
- 5.1.1 Universal Control (Windows only)
- 5.1.2 Loopback Recording (Windows only)
- 5.1.3 Using the StudioLive for System Sound
- 5.2 Installation for macOS
- 5.2.1 Using the StudioLive for System Sound
- 5.3 Using the StudioLive with Popular Audio Applications
- 5.4 Digital Sends and Returns
- 5.4.1 Digital Sends
- 5.4.2 Digital Returns
- 6 Capture 2
- 6.1 Installation Instructions
- 6.1.1 macOS
- 6.1.2 Windows
- 6.2 Start Page
- 6.2.1 Tagging and Organizing a Session
- 6.2.2 Creating a Session
- 6.2.3 Open a Session
- 6.2.4 Audio Device and Sample Rate
- 6.2.5 Options Menu
- 6.3 The Session Page
- 6.3.1 Track Column
- 6.3.2 Transport
- 6.3.3 Time Display
- 6.3.4 Timeline Ruler
- 6.3.5 Navigating the Session
- 6.3.6 Editing Tools
- 6.3.7 Meter Bridge
- 6.3.8 Markers and the Marker List
- 6.4 Recording a Session in Capture
- 6.5 Importing and Exporting Audio Files
- 6.5.1 Importing Audio Files into Capture
- 6.5.2 Export Audio Files
- 6.6 Mixing Your Capture Sessions
- 6.6.1 Exporting Your Final Mix to an Audio File
- 6.6.2 Mixing a Capture 2 Session in Studio One
- 6.6.3 Mixing a Capture 2 Session in a Different Recording Application
- 6.7 Capture 2 Key Commands
- 7 Studio One Artist Quick Start
- 7.1 Installation and Authorization
- 7.2 Setting Up Studio One
- 7.2.1 Configuring Audio Devices
- 7.2.2 Configuring MIDI Devices
- 7.3 Creating a New Song
- 7.3.1 Configuring Your I/O
- 7.3.2 Creating Audio and MIDI Tracks
- 7.3.3 Recording an Audio Track
- 7.3.4 Adding Virtual Instruments and Effects
- 8 Resources
- 8.1 EQ Frequency Guides
- 8.2 Block Diagrams
- 8.2.1 StudioLive AR16c, and AR12c Block Diagram
- 8.2.2 StudioLive AR8c Block Diagram
- 8.3 Recall Sheets
- 8.3.1 AR16c and AR12c Recall Sheet
- 8.3.2 AR8c Recall Sheet
- 8.4 Technical Specifications
- 9 Troubleshooting
- 9.1 Troubleshooting
20
5 Connecting to a Computer
5.1 Installation for Windows
StudioLive
™
ARc Series
Owner’s Manual
5.1.1 Universal Control (Windows only)
Sample Rate. Changes the sample rate.
You can set the sample rate to 44.1, 48, 88.2, or 96 kHz. A higher sample
rate will increase the fidelity of the recording but will increase the file size
and the amount of system resources necessary to process the audio.
Safe Mode. Adjusts the Input Buffer Size.
These modes allow you to adjust the input buffer size
to optimize performance for your computer.
When adjusting the safe mode, the block size will be adjusted
automatically to provide the best performance.
Block Size. Sets the buffer size.
From this menu, you can set the buffer size from 16 to 4,096 samples (Mac), or 64
to 8192 samples (Windows). Lowering the buffer size will lower latency; however,
this will also increase performance demands on your computer. In general, you will
want to set the buffer size as low as your system can safely support. If you begin
to hear pops, clicks, or distortion in your audio path, try raising the buffer size.
Note: When adjusting the block size, the Safe Mode will
automatically change to provide the best performance.
5.1.2 Loopback Recording (Windows only)
The windows drivers for the StudioLive ARc-series mixers provide two
virtual streams that allow you to record the output of on audio application
in another application. Loopback can be useful in a variety of situations:
• Recording the audio from a video game or YouTube
video for a podcast or livestream.
• Recording a vocal in real time over a karaoke track
played from a web browser or media player.
Power User Tip: Because the StudioLive ARc-series mixers are class compliant Core
Audio devices, these virtual streams are not available in macOS. However, there
are several third-party applications that provide this functionality in macOS.