User Manual
Table Of Contents
- 1 Overview
- 1.1 Introduction
- 1.2 About This Manual
- 1.3 What is in the Box
- 1.4 What is in your My PreSonus Account
- 2 Getting Started
- 2.1 Level-Setting Procedure
- 3 Hookup
- 3.1 Connections and Controls
- 3.1.1 Inputs
- 3.1.2 Outputs
- 3.1.3 Rear Panel Connections
- 3.2 Channel Controls
- 3.2.1 Digital Returns
- 3.3 The Super Channel
- 3.3.1 Pairing a Bluetooth Device
- 3.4 Aux Buses
- 3.4.1 Monitor Bus Controls
- 3.4.2 Creating Monitor Mixes
- 3.5 Internal FX Bus
- 3.5.1 Effects Presets
- 3.5.2 Internal FX Bus Return
- 3.5.3 Creating Internal Effects Mixes
- 3.5.4 Using an External Effects Processor
- 3.6 Master Section Controls
- 3.6.1 Control Room Levels
- 3.7 Typical Band Setup Diagram
- 3.8 Typical Home Studio Setup Diagram
- 4 SD Recording and Playback
- 4.1 SD Recording
- 4.2 SD Playback
- 5 Connecting to a Computer
- 5.1 Installation for Windows
- 5.1.1 Universal Control (Windows only)
- 5.1.2 Loopback Recording (Windows only)
- 5.1.3 Using the StudioLive for System Sound
- 5.2 Installation for macOS
- 5.2.1 Using the StudioLive for System Sound
- 5.3 Using the StudioLive with Popular Audio Applications
- 5.4 Digital Sends and Returns
- 5.4.1 Digital Sends
- 5.4.2 Digital Returns
- 6 Capture 2
- 6.1 Installation Instructions
- 6.1.1 macOS
- 6.1.2 Windows
- 6.2 Start Page
- 6.2.1 Tagging and Organizing a Session
- 6.2.2 Creating a Session
- 6.2.3 Open a Session
- 6.2.4 Audio Device and Sample Rate
- 6.2.5 Options Menu
- 6.3 The Session Page
- 6.3.1 Track Column
- 6.3.2 Transport
- 6.3.3 Time Display
- 6.3.4 Timeline Ruler
- 6.3.5 Navigating the Session
- 6.3.6 Editing Tools
- 6.3.7 Meter Bridge
- 6.3.8 Markers and the Marker List
- 6.4 Recording a Session in Capture
- 6.5 Importing and Exporting Audio Files
- 6.5.1 Importing Audio Files into Capture
- 6.5.2 Export Audio Files
- 6.6 Mixing Your Capture Sessions
- 6.6.1 Exporting Your Final Mix to an Audio File
- 6.6.2 Mixing a Capture 2 Session in Studio One
- 6.6.3 Mixing a Capture 2 Session in a Different Recording Application
- 6.7 Capture 2 Key Commands
- 7 Studio One Artist Quick Start
- 7.1 Installation and Authorization
- 7.2 Setting Up Studio One
- 7.2.1 Configuring Audio Devices
- 7.2.2 Configuring MIDI Devices
- 7.3 Creating a New Song
- 7.3.1 Configuring Your I/O
- 7.3.2 Creating Audio and MIDI Tracks
- 7.3.3 Recording an Audio Track
- 7.3.4 Adding Virtual Instruments and Effects
- 8 Resources
- 8.1 EQ Frequency Guides
- 8.2 Block Diagrams
- 8.2.1 StudioLive AR16c, and AR12c Block Diagram
- 8.2.2 StudioLive AR8c Block Diagram
- 8.3 Recall Sheets
- 8.3.1 AR16c and AR12c Recall Sheet
- 8.3.2 AR8c Recall Sheet
- 8.4 Technical Specifications
- 9 Troubleshooting
- 9.1 Troubleshooting
4
2 Getting Started
2.1 Level-Setting Procedure
StudioLive
™
ARc Series
Owner’s Manual
6. If your microphone requires phantom power, engage the 48V button on
your StudioLive ARc mixer.
7. Turn on your amplifier or powered monitors.
8. Speak or sing into your microphone at approximately the same volume you
expect during the performance.
9. Turn the trim knob on Channel 1 clockwise while watching the signal
indicator. Adjust the Channel 1 trim knob until the signal/clip indicator is
red, then back down until it is green and just below clipping at the loudest
input level.
10. Raise the Channel 1 level control to unity gain (denoted with a “U”).
11. Bring up the Main level until you can comfortably listen to your microphone
through your speakers.
12. Sculpt the sound by adding EQ to taste.