Owner’s Manual Exeter, PA St. Catharines, ON 1-800-800-8586 www.pridemobility.
SAFETY GUIDELINES The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Failure to follow designated procedures can cause either personal injury, component damage, or malfunction (black symbol on yellow triangle with black border). MANDATORY! These actions should be performed as specified.
CONTENTS I. INTRODUCTION................................................................................................................................. 4 II. SAFETY ................................................................................................................................................. 6 III. YOUR POWER CHAIR .................................................................................................................... 15 IV. ASSEMBLY/DISASSEMBLY .........................
I. INTRODUCTION SAFETY WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-ofthe-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for your power chair, it should give you years of trouble free operation and service.
I. INTRODUCTION PRIDE OWNERS CLUB As an owner of a Pride product, you are invited to register your product's warranty and enroll in the Pride Owners Club. You may do so by filling out and returning your enclosed product registration card or by visiting Pride's web site at www.pridemobility.com. As a registered member, each time you visit our site, you will have access to the most interactive and honest educational venue available today for people with mobility needs, their families, and friends.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Corrosive chemicals contained in battery. Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions. EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m. Read and follow the information in the owner’s manual. Maximum seating weight.
II. SAFETY Do not remove anti-tip wheels. Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating. Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and store in a clean and dry condition. Removal of grounding prong can create electrical hazard. If necessary, properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure to heed could result in personal injury and/or property damage.
II. SAFETY SAFETY MANDATORY! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user.
II. SAFETY Weight Limitations Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit. WARNING! Exceeding the weight capacity voids your warranty and may result in personal injury and/or damage to your power chair. Pride will not be held responsible for injuries and/or property damage resulting from failure to observe weight limitations. WARNING! Do not carry passengers on your power chair.
II. SAFETY WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated in figure 1, do not, under any circumstances, exceed the incline guidelines or any other specifications presented in this manual. Doing so could cause instability in your power chair, resulting in personal injury and/ or damage to your power chair. In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to have a maximum slope of 5° (8.7%).
II. SAFETY Freewheel Mode Your power chair is equipped with a manual freewheel system to allow for manual maneuverability by a trained attendant. For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.” WARNING! Do not use your power chair in freewheel mode without an attendant present. Personal injury may result. WARNING! Do not attempt to personally place your power chair in freewheel mode while seated on it. Personal injury may result.
II. SAFETY Transfers Transferring onto and off of your power chair requires a good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself. To eliminate the possibility of injury, Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer: ! Turn off the power to the controller See VII. “Operation.” ! Ensure your power chair is not in freewheel mode. See III. “Your Power Chair.
II. SAFETY Positioning Belts Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your power chair safely. WARNING! If you require a positioning belt to safely operate your power chair, make sure it is fastened securely. Serious personal injury may result if you fall from the power chair. WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle.
II. SAFETY Preventing Unintended Movement WARNING! If you anticipate being seated in a stationary position for an extended period of time, turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources. Failure to do so may result in personal injury. Removable Parts WARNING! Do not attempt to lift or move a power chair by any of its removable parts.
I I I . YO U R P OW E R C H A I R THE JAZZY 1107 The Jazzy has two main assemblies: the seat assembly and the power base assembly. See figure 5. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brake assemblies, two drive wheels, two anti-tip wheels, two caster wheels, two battery boxes, and wiring harnesses. See figures 5, 6, and 7.
I I I . YO U R P OW E R SIDE TRAPEZE BARS C H A I R FRONT TRAPEZE BAR BATTERY BOX CONTROLLER CONNECTOR BATTERY BOX MANUAL FREEWHEEL LEVER MOTOR/BRAKE ASSEMBLY Figure 6. The Jazzy 1107 Power Base 16 www.pridemobility.
I I I . YO U R P OW E R C H A I R JAZZY 1107 SPECIFICATIONS Suspension: Active Trac Drive Wheels: 10 in., pneumatic, (10 in., solid are optional) Caster Wheels: 6 in., solid, rear-mounted Anti-tip Wheels: 5 in., solid, front-mounted Maximum Speed:¹ Up to 4.5 mph Brakes: “Intelligent Braking” electronic regenerative, disc park brake Ground Clearance:² 2.5 in. Turning Radius:² 21.875 in. (with foot platform) Overall Size:² Length: 40.25 in. (with foot platform) Width: 23.375 in.
I I I . YO U R P OW E R C H A I R Battery Harness Connector: This is where the controller connects to the battery boxes. Main Circuit Breaker (located on rear battery box): The main circuit breaker is a safety feature built into your power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute.
I I I . YO U R P OW E R C H A I R Manual Freewheel Levers Your power chair has a manual freewheel lever on each motor. See figure 6. Manual freewheel levers enable you to disengage the drive motors from the gearboxes and maneuver the chair manually. WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage the drive motors when the power chair is on an incline, as the unit could roll on its own, causing injury! To engage or disengage the drive motors: 1.
I V. ASSEMBLY/DISASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
I V. ASSEMBLY/DISASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base.
I V. ASSEMBLY/DISASSEMBLY Power Base Disassembly The Jazzy 1107 power base disassembles into six parts for easy transportation and storage. See figure 13. To disassemble the power base: 1. Turn off the power to the controller. 2. Disconnect the controller from the power base. See figure 6. 3. Remove the seat. 4. Press the foot platform release button and lift off the foot platform. See figure 13. 5. Flip down the battery box latches on each side of the power base. See figure 14. 6.
I V. CENTER SECTION LATCH ASSEMBLY/DISASSEMBLY BATTERY BOX LATCH (UNLOCKED) BATTERY BOX LATCH (LOCKED) Figure 14. Battery Box Removal and Frame Separation Jazzy 1107 www.pridemobility.
V. COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort. These adjustments include seat height and angle, armrest angle, foot platform height and angle, and controller position. If your power chair is equipped with a Specialty Seat or a Synergy Seat, refer to the information provided in separate manuals.
V. COMFORT ADJUSTMENTS Seat Position You can move the seat forward or rearward by changing the extrusion mounting position. To change the position: 1. Unplug the controller from the power base. 2. Remove the seat from the power base. 3. Removebothextrusionsfromthebottomoftheseat.Seefigure17. 4. Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backward. See figure 17. 5.
V. COMFORT To change the armrest width: 1. Locate the armrest knob on each side of the armrest receiver bracket. See figure 18. 2. Loosen each knob. 3. Slide the armrests in or out to the desired width. 4. Tighten each knob. Armrest Angle Adjustment To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 18. 2. Loosen the jam nuts. 3.
V. COMFORT ADJUSTMENTS To clamp the quick release fastener: 1. Make sure the lever is in the open position. 2. Turn the nut clockwise until it is snug. 3. Rotate the lever until it is in the fully closed position. NOTE: If the lever will not rotate to the fully closed position, then turn the nut counterclockwise one-quarter or one-half turn. SETSCREW Foot Platform Angle Adjustment You can adjust the angle of the foot platform with a hex key. See figure 21. To adjust the foot platform angle: 1.
V. COMFORT ADJUSTMENTS Swing-away Footrests Swing-away Footrests (SFRs) enable you to rotate the footrests to the side before you transfer onto or off of your power chair. RELEASE LEVER A RELEASE LEVER B LEG REST EXTENSION To rotate the SFRs: 1. Push in the release lever. See figure 23. 2. Rotate the SFRs. ADJUSTMENT SCREWS To adjust the SFR length: 1. Remove the two adjustment screws from the side of each footrest extension. See figure 23. 2. Slide the footrest up or down to the desired length. 3.
V. COMFORT ADJUSTMENTS To change foot plate position (B): 1. Remove the hardware. 2. Move the foot plate to the desired position. 3. Reinstall the hardware. To change foot plate tilt (C): 1. Loosen the hardware. 2. Tilt the foot plate to desired position. 3. Tighten the hardware. BOLT B To change foot plate angle (D): 1. Turn the setscrew clockwise to decrease the angle. 2. Turn the setscrew counterclockwise to increase the angle.
VI. BATTERIES AND CHARGING BATTERIES AND CHARGING Your Pride Power Chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
VI. BATTERIES AND CHARGING To charge the batteries using the off-board charger: 1. Position your power chair next to a standard electrical outlet. 2. Be certain the controller power is turned off. 3. Plug the off-board charger into the off-board charger/ programming socket on the controller. See VII. “Operation.” 4. Plug the off-board charger into the electrical outlet. NOTE: If it is a Pride off-board charger, then there are two lights in it.
VI. BATTERIES AND CHARGING How often must I charge the batteries? Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a daily basis or you may not use it for weeks at a time. ! Daily Use If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair. Your power chair will be ready each morning to give you a full day’s service.
VI. BATTERIES AND CHARGING It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in your battery properly.
VII. OPERATION FLIGHT CONTROLLER The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to the appropriate system. The electronic controller enables you to move the power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system. The FLIGHT is part of a modular electronic controller system. The system consists of more than one module.
VII. OPERATION On/Off Key The on/off key turns the FLIGHT on and off. WARNING! Unless faced with an emergency situation, do not use the on/off key to stop the chair. This will cause the power chair to stop abruptly. WARNING! Always turn the power off when you are stationary to prevent unexpected movement. Battery Condition Meter The battery condition meter consists of ten lights arranged in an arc over the on/off key. As the battery voltage drops, the number of lights reduces from right to left.
VII. OPERATION Speed Keys There are two keys that control the speed. Press the hare key to increase the speed. Press the tortoise key to decrease the speed. The speed setting is displayed on the speed indicator. If your power chair was programmed with a drive profile, contact your authorized Pride Provider for more information. NOTE: We recommend that the first few times you operate your power chair, you set the speed to the slowest setting until you become familiar with your new power chair.
VII. OPERATION VSI ELECTRONIC CONTROLLER The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system. The VSI electronic controller is an integral electronic controller. All of the electronics necessary to operate the power chair are contained in one module. See figure 30.
VII. OPERATION On/Off Key The on/off key turns the VSI on and off. WARNING! Unless faced with an emergency situation, do not use the on/off key to stop the power chair. This will cause the power chair to stop abruptly. WARNING! Always turn the power off when you are stationary to prevent unexpected movement. Battery Condition Meter The battery condition meter is a 10-segment illuminated display located in front of the joystick. It consists of red, yellow, and green lights.
VII. OPERATION Actuator Keys and Actuator Lights (For Optional Equipment) Actuator keys and actuator lights are used for optional equipment such as power elevating leg rests. For specific operation of the actuator keys and actuator lights, contact your authorized Pride Provider. Horn Key The horn key activates the horn. Locking/Unlocking the VSI The VSI has a feature that enables you to lock your power chair to prevent unauthorized use. To lock the VSI: 1.
VII. OPERATION WARNING! Failure to properly align the connectors can result in damage to the VSI, the charger, and the connectors. Thermal Rollback The VSI controller is equipped with a thermal rollback circuit. This circuit monitors the temperature of the controller, which roughly translates to motor temperature. In the event that the VSI controller becomes excessively hot (above 140° F), motor current (amperage) is reduced. For every degree above 131° F, the motor current limit is reduced by .55 amps.
VIII. CARE AND MAINTENANCE CARE AND MAINTENANCE Your Pride Power Chair is a sophisticated device. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your authorized Pride Provider. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation.
VIII. CARE AND MAINTENANCE ! Check all electrical connections. Make sure they are tight and are not corroded. ! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication. Daily Checks ! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot. Do not handle or try to repair it.
VIII. CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.” WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged. Disposal of Your Power Chair Your power chair must be disposed of according to applicable local and national statutory regulations.
VIII. CARE AND MAINTENANCE 4. Remove the drive wheel nut and washer from the axle. See figure 32. 5. Pull the wheel off the axle. 6. Remove the nuts and washers from the wheel hub and separate the front and rear rim. See figure 33. 7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire. 8. Reassemble the rims and reinstall the nuts and washers to the wheel hub. 9. Slide the wheel back onto the axle.
VIII. 3. 4. 5. 6. 7. CARE AND MAINTENANCE Remove the battery boxes. See IV. “Assembly/Disassembly.” Disconnect the wiring harness from the batteries. Remove the batteries from the battery boxes. Place new batteries in the battery boxes. See figure 34. Reconnect the battery harnesses according to the battery wiring diagram label. See figure 35. WARNING! Prevent injury. Make sure you tighten the fasteners so that the connections are secure. 8. Reinstall the battery boxes onto the power base.
IX.
IX. WARRANTY RECONDITIONED UNITS WARRANTY All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase. WARRANTY EXCLUSIONS This warranty does not extend to those items which may require replacement due to normal wear and tear.
NOTES 48 www.pridemobility.
NOTES Jazzy 1107 www.pridemobility.
NOTES 50 www.pridemobility.
# In Q 1 Conuality trol Quality Control - 1107 Thank you for making the Jazzy 1107 your choice in power chairs. The following checkmarks indicate that we have thoroughly inspected and test driven your power chair. Inclusion of all Parts Joystick Serial Number Controller Serial Number Left Motor Serial Number Right Motor Serial Number Fit and Finish Performance Pride keeps a more detailed report on file at the factory.