Quality Control - Jazzy 614 Series Inclusion of all Parts JAZZY 614 SERIES Joystick Serial Number Controller Serial Number Left Motor Serial Number Right Motor Serial Number Fit and Finish Performance Pride keeps a more detailed report on file at the factory.
SAFETY GUIDELINES WARNING! An authorized Pride Provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
CONTENTS I. INTRODUCTION .................................................................................................................................. 4 II. SAFETY ................................................................................................................................................... 5 III. YOUR POWER CHAIR ..................................................................................................................... 17 IV. ASSEMBLY .................................
I. INTRODUCTION SAFETY WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines stateof-the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for your power chair, it should give you years of trouble-free operation and service.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Do not allow unsupervised children to play near the power chair while the batteries are charging. Maximum seating weight. Keep your hands away from the tires when driving.
II. SAFETY Removal of grounding prong can create electrical hazard. If necessary, properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Do not connect an extension cord to the AC/DC converter or the battery charger. Do not place power chair in freewheel mode on a decline. Do not place power chair in freewheel mode on an incline. Wear safety goggles. Corrosive chemicals contained in battery.
II. SAFETY Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions. Keep tools and other metal objects away from battery terminals. Contact with tools can cause electrical shock. Battery Set Configuration: + = Positive (Red) Terminal Post - = Negative (Black) Terminal Post Connect Red wires to Red Positive (+) Terminal Posts Connect Black wires to Black Negative (–) Terminal Posts Do not use batteries with different amp-hour (Ah) capacities.
II. SAFETY Unlocked and in freewheel mode. Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode. Locked and in drive mode. Do not adjust suspension. Power chair information label - Jazzy 614 Power chair information label - Jazzy 614HD 8 www.pridemobility.
II. SAFETY GENERAL GUIDELINES MANDATORY! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual. Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user.
II. SAFETY Weight Limitations Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit. Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories mounted to the power chair. MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight capacity voids your warranty.
II. SAFETY WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiate inclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seat in a reclined position unless an attendant is present to help stabilize the chair. Failure to heed may result in the power chair tipping over.
II. SAFETY Public Streets and Roadways WARNING! You should not operate your power chair on public streets and roadways. Be aware that it may be difficult for traffic to see you when you are seated on your power chair. Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with extreme caution.
II. SAFETY Figure 2. Correct Curb Approach Figure 3. Incorrect Curb Approach WARNING! Even though your power chair may be capable of handling greater obstacles, Pride recommends that you do not attempt to negotiate a curb that has a height greater than 2 in. (5 cm). Doing so could cause instability in your power chair. WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or other obstacle. This may cause the power chair to tip.
II. SAFETY Positioning Belts Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your power chair safely. WARNING! If you require a positioning belt to safely operate your power chair, make sure it is fastened securely in order to reduce the possibility of a fall from the power chair. WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle.
II. SAFETY Transfers Transferring onto and off of your power chair requires a good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself. To eliminate the possibility of injury, Pride recommends that you or a trained attendant perform the following tasks before attempting a transfer: Turn off the power to the controller. Ensure your power chair is not in freewheel mode. See III. “Your Power Chair.
II. SAFETY Prescription Drugs/Physical Limitations Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations. WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or if you have certain physical limitations. Some medications and limitations may impair your ability to operate your power chair in a safe manner.
III. YOUR POWER CHAIR THE JAZZY 614 SERIES Your power chair has two main assemblies: the seat assembly and the power base assembly. See figure 5. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/ brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figures 5, 6, and 7.
III. YOUR POWER CHAIR TRAPEZE BARS FRONT COVER Figure 6. The Jazzy 614 Series Power Base Electrical components The electrical components are located on or inside the power base. The main circuit breaker is located on the front of the power base. The power module is located inside the power base. See figure 7. Motor Connectors: This is where the controller connects to the motors. Battery Connector: This is where the controller connects to the batteries.
III. YOUR POWER CHAIR Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit breaker trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit breaker button, turn on the controller, and continue normal operation.
III. YOUR POWER CHAIR Manual Freewheel Levers For your convenience, your power chair is equipped with two manual freewheel levers mounted on the motors. These levers allow you to disengage the drive motors and maneuver the chair manually. You can manually push the power chair by the seatback.
IV. ASSEMBLY INITIAL ASSEMBLY Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
IV. ASSEMBLY Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any mediumback or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base.
V. COMFORT ADJUSTMENTS COMFORT ADJUSTMENTS After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. NOTE: If your power chair is equipped with a Synergy Seat or TRU-Balance Power Positioning System, refer to the seat adjustment information contained in separate manuals.
V. COMFORT ADJUSTMENTS 10. Reinstall the retaining clips from step 8. 11. Remove each screw from the trapeze bars and apply thread lock. 12. Reinstall each screw into the trapeze bars and tighten. 13. Tighten the setscrew in each seat tower. See figure 14. 14. Reinstall the seat. 15. Lift the armrest straight up, then route the controller harness so that it can not be pinched in the seat hinge. See figure 11. 16. Reconnect the controller to the power base. 17.
V. COMFORT ADJUSTMENTS Seatback Angle Adjustment If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°. To adjust the seatback angle: 1. Remove the adjusting screws from each seat hinge. See figure 16. 2. Set the seatback at the desired angle. 3. Reinstall the adjusting screws to each seat hinge and tighten. Armrest Width Adjustment You can change each armrest’s width independently of the other.
V. COMFORT ADJUSTMENTS Controller Position You can move the controller in toward or out away from the armrest, or change the position of the controller for either left-hand or right-hand use. WARNING! Do not place the controller harness so that it can be pinched in the seat frame or the power base frame. CONTROLLER BRACKET To extend the controller: 1. Flip up the armrest so it is perpendicular to the floor. 2. Loosen the setscrew on the controller bracket. See figure 17. 3.
V. COMFORT ADJUSTMENTS Foot Platform Depth Adjustment To adjust the foot platform depth: 1. Remove the hardware from the foot platform bracket. See figure 18. 2. Move the foot platform in or out to the desired depth. 3. Reinstall the hardware into the foot platform bracket and tighten. Foot Platform Angle Adjustment You can adjust the angle of the foot platform with a hex key. See figure 19. To adjust the foot platform angle: 1. Flip up the foot platform and locate the adjustment screw. 2.
VI. BATTERIES AND CHARGING BATTERIES AND CHARGING Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
VI. BATTERIES AND CHARGING To charge the batteries using the off-board charger: 1. Position the front of your power chair next to a standard electrical outlet. 2. Be certain the controller power is turned off. 3. Plug the off-board charger into the off-board charger/programming socket on the controller. See figure 20. 4. Plug the off-board charger into the electrical outlet.
VI. BATTERIES AND CHARGING How often must I charge the batteries? Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a daily basis or you may not use it for weeks at a time. Daily Use If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair. Your power chair will be ready each morning to give you a full day’s service.
VI. BATTERIES AND CHARGING How can I ensure maximum battery life? A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.
VII. CARE AND MAINTENANCE CARE AND MAINTENANCE Your Jazzy 614 Series is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your authorized Pride Provider. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your power chair gives you years of trouble-free operation.
VII. CARE AND MAINTENANCE All wheel bearings are prelubricated and sealed. They require no subsequent lubrication. The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain its high-gloss appearance. Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery tray, with the battery terminals facing inward, toward each other.
VII. CARE AND MAINTENANCE Storage Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.” WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged.
VII. CARE AND MAINTENANCE TIRE AXLE KEY TUBE AXLE SLOT FRONT RIM HALF SCREWS REAR RIM HALF DRIVE WHEEL WASHER DRIVE WHEEL NUT Figure 21. Jazzy 614 Series Drive Wheel Figure 22. Jazzy 614 Series Drive Wheel Disassembled Follow these easy steps for a quick and safe repair for both pneumatic and solid tires: 1. Turn off the power to the controller. 2. Set the power chair up on blocks. 3. If you are changing a pneumatic tire, completely deflate it before removing the wheel. 4.
VII. CARE AND MAINTENANCE REAR SHROUD BATTERY WIRING DIAGRAM BATTERY STRAP PULL POINTS FOR REAR SHROUD REMOVAL DISCONNECT RELEASE BUTTON REAR BATTERY FRONT BATTERY Figure 23. Battery Installation 36 www.pridemobility.
VII. CARE AND MAINTENANCE To replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.” 3. Pull to remove the rear shroud. See figure 23. 4. Push down on the disconnect release button and disconnect the rear battery harness from the power base. See figure 23. 5. Unfasten the battery strap from around the rear battery. 6. Slide the rear battery out. 7.
APPENDIX I - SPECIFICATIONS SPECIFICATIONS Suspension ATX Suspension (Active-Trac with extra stability) Drive Wheels Jazzy 614 Series: 14 in. (35.56 cm), pneumatic or solid available Jazzy 614HD: 14 in. (35.56 cm), solid Caster Wheels 6 in. (15.24 cm), solid (front and rear) Maximum Speed1 Jazzy 614 Series: Up to 4.25 mph (6.84 km/h) Brakes “Intelligent Braking” electronic regenerative, disc park brake Ground Clearance2 See figure 24. Turning Radius2 See figure 24.
APPENDIX I - SPECIFICATIONS LENGTH 40.0 in. (101.6 cm) 35.5 in. (90.17 cm) WIDTH 25.125 in. (63.82 cm) 20.0 in. (50.8 cm) 2.25 in. (5.72 cm) 1.625 in. (4.12 cm) AT FOOT PLATFORM TURNING RADIUS GROUND CLEARANCE Figure 24. Jazzy 614 Series and Jazzy 614HD Dimensions and Ground Clearance Jazzy 614 Series www.pridemobility.
NOTES 40 www.pridemobility.
NOTES Jazzy 614 Series www.pridemobility.
NOTES 42 www.pridemobility.
SAFETY GUIDELINES WARNING! An authorized Pride Provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
Quality Control - Jazzy 614 Series Inclusion of all Parts JAZZY 614 SERIES Joystick Serial Number Controller Serial Number Left Motor Serial Number Right Motor Serial Number Fit and Finish Performance Pride keeps a more detailed report on file at the factory.