Bluetooth® Headset Badge BHS-608 User Guide kansilehti_608.indd 1 19.6.
BHS-608_UG_en.fm Page 1 Wednesday, August 10, 2005 4:27 PM EN ENGLISH About Bluetooth® Technology ............................................................................................... 2 Introduction ........................................................................................................................... 3 Getting Started ...................................................................................................................... 6 Charging the Battery ..................
BHS-608_UG_en.fm Page 2 Wednesday, August 10, 2005 4:27 PM About Bluetooth® Technology Bluetooth is a technology for wireless communication between devices. Bluetooth technology is based on a radio with a receiver and a transmitter that have been built into a tiny microchip. One of these microchips is incorporated in the Wireless Headset, while the other is integrated into the compatible mobile phone.
BHS-608_UG_en.fm Page 3 Wednesday, August 10, 2005 4:27 PM EN Introduction Thanks for purchasing a Iqua Bluetooth Smart Badge BHS-608. Your Smart Badge is a stylish product that enables comfortable hands-free communication with compatible mobile phones that supports Bluetooth wireless technology. The Smart Badge contains the following parts, as shown in Fig. 1.
BHS-608_UG_en.fm Page 4 Wednesday, August 10, 2005 4:27 PM (1) Power key Power on/off and mute button, switches the headset on and off or mutes the on-going call. (2) Indicator Light • • Power on - green light flashes 5 times and beeps once • • • • • • Connectable - green light flashes every 3 sec Pairing state - green and red lights flash in turns, the flashing continues for approximately 10 minutes or until the headset is connected to a compatible phone.
BHS-608_UG_en.fm Page 5 Wednesday, August 10, 2005 4:27 PM EN (6) Send / End key • • • • Answer incoming call • • End active call Switch between the headset and phone mode by pressing the button for a long time Redial the last number dialed by pressing the button twice when no call is being made Voice dial is activated by pressing the button for a long time (phone-dependent) when no call is being made Reject incoming call by pressing the button twice (7) Earpiece Relays the caller's voice.
BHS-608_UG_en.fm Page 6 Wednesday, August 10, 2005 4:27 PM Getting Started Remove all of the components from the package: 1. Smart Badge 2. USB cable 3. Plastic window 4. Carrying Case 5. Travel Charger 6. User Guide 1. 3. 4. 2. 5.
BHS-608_UG_en.fm Page 7 Wednesday, August 10, 2005 4:27 PM EN Charging the Battery Before using Smart Badge, you must charge the product for approximately 5 hours. Once the battery is fully charged, it will provide up to 40 hours of talk time and up to 600 hours of standby time. 1. Connect the charger cable to the Smart Badge. 2. Plug the AC adapter into a wall outlet. When the Smart Badge is charging, a red indicator light will appear and stay lit. 3.
BHS-608_UG_en.fm Page 8 Wednesday, August 10, 2005 4:27 PM 3. Activate the Bluetooth connection from the phone. For more information, see your phone's User Guide. 4. Set the phone to search for Bluetooth devices as instructed in your phone's User Guide. 5. Select BHS-608 from the list. 6. Enter the pin code 0000 to connect (or "pair") your Smart Badge and your phone Your Smart Badge will beep once, after which a blinking blue indicator light will indicate that the Bluetooth connection is active.
BHS-608_UG_en.fm Page 9 Wednesday, August 10, 2005 4:27 PM EN Disconnecting Smart Badge from a Phone To disconnect your Smart Badge from your phone, do any one of the following: • • • Turn off the Smart Badge. Disconnect the Smart Badge in the phone menu. Move the Smart Badge more than 10 meters away from the phone. The Smart Badge will also be disconnected if the battery is empty. Note that you do not need to delete the pairing with the headset to disconnect it.
BHS-608_UG_en.fm Page 10 Wednesday, August 10, 2005 4:27 PM Powering Up To turn on the Smart Badge Press and hold down the Power key for 2 seconds. The Smart Badge will beep and the green indicator light start to blink. The blinking will continue for approximately 10 minutes or until the headset is connected to a compatible phone. If the headset cannot be connected to a phone during this time, the Smart Badge will turn off. To turn off the Smart Badge Press and hold down the Power key for 2 seconds.
BHS-608_UG_en.fm Page 11 Wednesday, August 10, 2005 4:27 PM EN Rejecting a Call When you receive an incoming call that you do not want to answer, simply press the Send/ End key twice. Redialing the Last Dialed Number Press the Send/End key twice when no call is in progress. Muting an on-going Call You can mute or unmute the on-going call by briefly pressing the Power key.
BHS-608_UG_en.fm Page 12 Wednesday, August 10, 2005 4:27 PM Switching the Call between Phone and Headset Mode Press and hold the Send/End key or use the Respect function in your phone. Switching between on-going calls and waiting calls When a call is being made and another call is coming in, simply press the Volume down key and hold it down for 2 seconds or use the respect function in your phone.
BHS-608_UG_en.fm Page 13 Wednesday, August 10, 2005 4:27 PM EN Warning Headset – Please turn off your Smart Badge before putting it in your pocket or bag. If it is not turned off and the Send/End key is pressed accidentally, the headset may answer a call with you knowing it. – – Do not expose the headset to liquid, moisture or humidity as it is not waterproof. Do not use abrasive cleaning solvents to clean the headset. – Do not expose the headset to high or low temperatures.
BHS-608_UG_en.fm Page 14 Wednesday, August 10, 2005 4:27 PM Product Specifications Bluetooth Specification: Bluetooth Profile Supported: Rang of Frequency: Dimensions: Weight: Nominal Charging Time: Talk time: Standby time: Version 1.2 Headset and Handsfree Profiles 2.4GHz Spectrum 100mm (L) x 70mm (W) x 13mm (H) 45 g (main body) Within 5 hours Up to 40 hours Up to 600 hours Because operation of Bluetooth is dependent on individual phone, please refer to phone user guide.
BHS-608_UG_en.fm Page 15 Wednesday, August 10, 2005 4:27 PM EN 12 MONTH LIMITED WARRANTY IQUA Ltd. warrants that this product is free from material and workmanship defects for a period of 12 months from date of purchase provided the following terms of this warranty are satisfied. This warranty only applies to the original owner of this product. 1.
BHS-608_UG_en.fm Page 16 Wednesday, August 10, 2005 4:27 PM 6. The warranty is not valid in case of fire, lighting, earthquake, accident, misuse, unusual physical or electrical stress or any other cause beyond the normal usage and care of the product. 7. IQUA Ltd. reserves the right to make changes or improvements in design or manufacture without having any obligation to install such changes in existing and sold products. 8.
