User's Manual

Indicator
Volume down
Power/Send/End
button
Microphone
Volume up
Visor clip
Charger
connector
QUICK SETUP GUIDE
QS2 Car Speakerphone
RF-QS2
Congratulations on your purchase of the RF-QS2
Bluetooth carkit. This carkit enables comfortable,
hands-free communication with a Bluetooth-compatible
phone.
Package contents
• RF-QS2 carkit • Car charger adapter
• USB charging cable • Quick Setup Guide
Features
Charging the battery
Before using your carkit, you must charge it for about
two hours. When the battery is fully charged, it provides
up to 11 hours of talk time and up to 1,400 hours of
standby time.
1 USB charging: use the USB cable to plug your QS2
speakerphone into a computer or other USB power
port.
2 Car charging: use the car charger adapter and USB
charging cable to charge your QS2 speakerphone in
your car.
Turning the carkit on
Press and hold the Power/Send/End for about 2
seconds. RF-QS2 beeps and the yellow-green indicator
light starts blinking. (First time use requires pressing it
for 4 seconds.)
Turning the carkit o
Press and hold the Power/Send/End for about 4
seconds, RF-QS2 beeps and the red indicator light is
displayed briey.
Pairing the carkit
1 Make sure that the compatible phone is turned on
and within 33 ft. (10 m) of the carkit.
2 Turn on the QS2 and make sure it’s fully charged.
Press and hold the Power/Send/End button for
about four seconds. The yellow-green indicator
ashes rapidly. Release the button. The carkit is now
in pairing mode.
3 Activate the Bluetooth connection from the phone.
See your phone’s documentation for more
information.
4 Set the phone to start searching for Bluetooth
devices.
5 Select RF-QS2 from the list.
6 Enter the PIN 0000 to connect (or “pair”) the carkit to
the phone. The carkit beeps once, and the indicator
blinks yellow-green to indicate the Bluetooth
connection is active.
To... Do this...
Make a call Press Po wer/Send/End.
Redial Double-press Pow er/Send/End.
Answer a call Press Po wer/Send/End.
End a call Press Po wer/Send/End.
Refuse a call Double-press Power/Send/End.
Change the speaker Press the volume up button (+) to increase
volume volume or press the volume down (-) button to
decrease.
Mute or unmute a call Press and hold the Volume down (-) button until
a tone is heard.
Switch a call between Press and hold Po wer/Send/End for
the phone and the carkit two seconds.
Voice dialing
When no call is in progress, quickly press and release
Power/Send/End. When you hear a tone, speak the
number or voice tag for the number you want to call.
(The phone must have a voice dial feature and have
recorded voice tags.)
Making a call
Turning the indicator on or o
• Press the power and volume up buttons at the same
time for about four seconds. The indicator turns on.
Press the power and volume down buttons at the
same time for about four seconds. The indicator
turns o. You can enable or disable the indicator
when the carkit is connected with your phone.
Disconnecting the carkit from the phone
To disconnect the carkit from the phone, do one of the
following:
• Turn o the carkit.
• Disconnect the RF-QS2 in the phone’s menu.
• Move the carkit more than 33 ft. (10 m) away from
the phone.
Note: You do not need to delete the pairing to
disconnect the carkit. When you reconnect a paired
carkit, you will not be asked for its PIN again.
If you want to pair your car kit with new phones, you
don’t need to erase all paired device information.
There can be up to 8 dierent paired devices
information stored.
To erase paired devices from your car kit:
• When the carkit turned o, press and hold the
Power/Send/End and volume up (+) buttons
simultaneously for more than six seconds. A tone
plays, and the indicator ashes red and yellow-green.
The carkit then enters the pairing state
automatically.
v1
R4