www. .ch WA 508 E User manual Washing Machine 0848 559 111 www.fust.
CONTENTS Safety information Product description Control panel First use Daily use Washing Programmes Helpful hints and tips 2 4 5 6 6 9 12 Care and cleaning What to do if… Technical data Consumption values Installation Environment concerns 13 17 20 20 21 24 Subject to change without notice SAFETY INFORMATION Important! Read carefully & keep for future reference. • The safety of Your appliance complies with the industry standards and with legal requirements on the safety of appliances.
• • • • • and drain hose and the worktop is not pressing the electrical supply cable against the wall. If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. Always be sure, that there is no water leakage from hoses and their connections after the installation. If the appliance is installed in a location subject to frost, please read the “dangers of freezing” chapter.
PRODUCT DESCRIPTION Your new appliance meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. Its new washing system allows total use of detergent and reduces water consumption so saving energy.
Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available). The prewash and soak detergent is added at the beginning of the wash programme. The stain remover is added during the stain action phase. Compartment for powder or liquid detergent used for main wash. If using liquid detergent pour it just before starting the programme. Compartment for liquid additives (fabric softener, starch).
– Prewash/Wash (Vorwäsche-Prélavage/Waschen-Lavage) – Rinse/Spin (Spülen-Rinçage/ Schleudern-Essorage) – End (Ende-Fin) Indicator pilot lights The Prewash/Wash light illuminates after pressing button 4. The Rinse/Spin light is on when the machine is rinsing or spinning phase. The End light illuminates at the end of the washing cycle. Table of symbols = Handwash = Rinse Hold FIRST USE • Ensure that the electrical and water connections comply with the installation instructions.
Select the available options by pressing buttons 2 and 3 Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before starting the programme. When these buttons are pressed, the corresponding pilot lights illuminate. When they are pressed again, the pilot lights go out. If an incorrect option is selected, the integrated red pilot light of the button 4 flashes for 3 times.
again. If you have chosen a delayed start, the machine will begin the countdown. If an incorrect option is selected, the red pilot light of the button 4 blinks 3 times and the message Err is displayed for a few seconds. Interrupting a programme Press the button 4 to interrupt a programme which is running, the corresponding green pilot light starts blinking. Press the button again to restart the programme. Cancelling a programme to cancel a proTurn the selector dial to gramme which is running.
WASHING PROGRAMMES Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Cottons (Koch-/Buntwäsche-Blanc/Couleurs) 90° - 60° Main wash - Rinses Maximum spin speed at 800 rpm Max. load 5 kg - Reduced load 2,5 kg 1) White cotton (heavily or normally soiled items). SPIN REDUCTION RINSE HOLD PREWASH 2) SUPER QUICK Cotton Eco (ECO/Coton ECO) 60° Main wash - Rinses Maximum spin speed at 800 rpm Max.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Delicates (Feinwäsche/Délicat) 40° - 30° Main wash - Rinses Maximum spin speed 700 rpm Max. load kg 2,5 - Reduced load kg 1,5 1) Delicate fabrics: acrylics, viscose, polyester. Options RINSE HOLD PREWASH 2) SUPER QUICK Handwash 40° - 30° Main wash - Rinses Maximum spin speed at 800 rpm Max. load 2 kg Special programme for delicate fabrics with «hand washing» care symbol.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Soak (Einweichen/Tremp.) 30° Prewash - Soak for about 40 minutes - Stop with water in the tub Max. load 5 kg Special programme for heavily soiled laundry. The machine performs a soak at 30°C. At the end of this time the machine will stop automatically with water left in the tub.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Detergent Compartment O = OFF (Aus/Arrêt) For cancelling the programme which is running or to switch the machine off . 1) If you select the Super Quick option by pressing button 3, we recommend that you reduce the maximum load as indicated. Full loading is possible however with somewhat reduced cleaning results.
All commonly available washing machine detergents may be used in this appliance: • powder detergents for all types of fabric • powder detergents for delicate fabrics (60°C max) and woollens • liquid detergents, preferably for low temperature wash programmes (60°C max) for all types of fabric, or special for woollens only. The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme.
Remove the drawer by pressing the catch downwards and by pulling it out. Flush it out under a tap, to remove any traces of accumulated powder. To aid cleaning, the top part of the additive compartment should be removed. Clean all parts with water. Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1.
Drain pump The pump should be inspected regularly and particularly if: • the appliance does not empty and/or spin; • the appliance makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump. • a problem with water draining is detected (see chapter “What to do if...” for more details). Warning! Before opening the pump door, switch the appliance off and remove the mains plug from the socket. Proceed as follows: 1. Unplug the appliance. 2.
When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tightened so as to stop leaks and young children being able to remove it. 9. Put the cap back on the emergency emptying hose and place the latter back in its seat. 10.
7. replace the emergency emptying hose in its seat after having plugged it; 8. screw the pump again and close the door. 7. Screw the hose back to the machine and make sure the connection is tight. 8. Turn on the water tap. Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: 1. pull out the plug from the power socket; 2. close the water tap; 3. if necessary, wait until the water has cooled down; 4. open the pump door; 5.
Problem Possible cause/Solution The washing machine does not start: The door has not been closed (the button 4 red light blinks). • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. • Replace the fuse. The programme selector dial is not correctly positioned and the button 4 has not been pressed.
Problem Possible cause/Solution Unsatisfactory washing results: Too little detergent or unsuitable detergent has been used. • Increase the detergent quantity or use another one. Stubborn stains have not been treated prior to washing. • Use commercial products to treat the stubborn stains. The correct temperature was not selected. • Check if you have selected the correct temperature. Excessive laundry load. • Reduce the laundry load. The door will not open: The programme is still running.
Mo Prodd. ... . No ... ... . ... ... .. Se r. No . ... ... ... If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ... ...
INSTALLATION Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. After removing all the packaging, carefully lay machine on it’s back to remove the polystyrene base from the bottom. 3. Unscrew the three bolts. 4. Slide out the relevant plastic spacers. 2.
vibration, noise and displacement of the machine during operation. Caution! Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Water inlet Warning! This appliance must be connected to a cold water supply. 1. Connect the water inlet hose supplied with the machine to a tap with a 3/4" thread.
Angle the hose to the left or right depending on the position of your water tap. 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use.
ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Warranty / customer service For each product we provide a two-year guarantee from the date of purchase or delivery to the consumer (with a guarantee certificate, invoice or sales receipt serving as proof). The guarantee covers the costs of materials, labour and travel.
Unsere Kundendienst-Telefonnummer: Le numéro de téléphone de notre service après-vente: Il nostro numero di telefono del servizio clientela: Our customer service telephone number: 0848 559 111 oder unter ou sur Internet oppure su Internet or in the internet www.fust.ch Dipl. Ing FUST AG Buchental 4 9245 Oberbüren Tel. (071) 955 50 50 Dipl. Ing. FUST AG Riedmoosstrasse 3172 Niederwangen-Bern Tel. (031) 980 11 11 Dipl. Ing. FUST AG An der Rheinstrasse 4414 Füllinsdorf Tel. (061) 906 95 00 Ing. dipl.
132936440-A-072011 www. .
