RFID Smart Label Developer’s Kit and Smart Label Pilot Printer Quick Setup Guide The Printronix T5000e Series of Thermal Printers TM
This Quick Setup Guide contains a CD-ROM with the following materials: • • • The User’s Manual Programmer’s Reference Manuals Useful utility programs The CD-ROM is located in a plastic pocket in the back cover. Do not discard this guide. If you move or pack the printer in the future, you will need to follow the instructions in this guide. For technical assistance, contact your Distributor/VAR/Reseller for service. For further assistance, contact the Printronix Customer Support Center.
The Printronix T5000 e Series of Thermal Printers RFID Smart Label Developer’s Kit and Smart Label Pilot Printer Quick Setup Guide
Software License Agreement CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING THIS PRINTER. USING THIS PRINTER INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE TO THESE TERMS AND CONDITIONS, PROMPTLY RETURN THE PRINTER AND ALL ACCOMPANYING HARDWARE AND WRITTEN MATERIALS TO THE PLACE YOU OBTAINED THEM, AND YOUR MONEY WILL BE REFUNDED. Definitions. “Software” shall mean the digitally encoded, machine-readable data and program.
2. IN NO EVENT WILL PRINTRONIX, INC. BE LIABLE FOR LOST PROFITS, LOST DATA, BUSINESS INTERRUPTIONS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF PRINTRONIX, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR ANY DAMAGES CAUSED BY THE ABUSE OR MANIPULATION OF THE SOFTWARE.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any change or modification to this product voids the user’s authority to operate it per FCC Part 15 Subpart A Section 15.21 regulations.
This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to European Standard EN 55022. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment. Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Printronix makes no representations or warranties of any kind regarding this material, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. Printronix shall not be held responsible for errors contained herein or any omissions from this material or for any damages, whether direct, indirect, incidental or consequential, in connection with the furnishing, distribution, performance or use of this material.
Table of Contents 1 RFID Smart Label Application And Reference Notes .............................. 11 Overview............................................................................. 11 What To Expect When Running Your RFID Application..... 12 Factors Affecting Smart Label Performance ................ 12 Overstruck Smart Labels.............................................. 13 Smart Label Characteristics .........................................
Table of Contents Printing Adjustments............................................................34 Printhead Pressure Adjustment ....................................34 Printhead Pressure Block Adjustments.........................34 Positioning The Media Sensors ....................................35 Running Auto Calibrate .......................................................36 Saving The Configuration ....................................................37 Run A Barcode Demo Test.........................
1 RFID Smart Label Application And Reference Notes Overview Congratulations on your purchase of the industry’s first Smart Label Developer’s Kit or Smart Label Pilot Printer. The intent of the kit is to provide a complete environment for the printing and encoding of RFID smart labels right out of the box. Printronix has specifically designed this kit to help you fast track your RFID pilot printer application through the use of a suite of Software Migration Tools (SMT).
Chapter 1 What To Expect When Running Your RFID Application • • Smart Label Developer’s Quick Setup Guide (this manual) • Technical support Application and reference notes (this chapter) The Printronix Smart Label Developer’s Kit also contains: • Two rolls of 500 smart labels with Alien Technology™ Class 1 64 data bits, 915MHz inlays • • One 625 m thermal premium wax ribbon Network interface card, which includes Printronix’s PrintNet® Enterprise, a remote network printer management software applica
Overstruck Smart Labels Overstruck Smart Labels If an RFID tag within a smart label is deemed unacceptable after execution of the defined number of retries, the following actions are performed: • If Error Handling is set to Overstrike (the default), the unacceptable smart label will print with a grid or error message over the label. If the Label Retry Count is greater than zero (the default is 10), the next smart label will be tried until the label retry count is exhausted.
Chapter 1 Transitioning From UCC/GTIN Applications Using Printronix Soft- Transitioning From UCC/GTIN Applications Using Printronix Software Migration Tools (SMT) It is likely that your software is already set up to create bar codes. You may have also spent a lot of time creating compliance label templates & integrating them into your system. The Smart Label Developer’s Kit Software Migration Tools will allow you to effortlessly transition from printing compliance labels to smart labels.
What We Can Do • EPC: This tool allows EPC data to be directly encoded into the smart label’s RFID tag. Simply have your existing software application write the desired EPC number to a Code 3 of 9 barcode. The printer will then write the EPC data to the RFID tag without printing the bar code. The existing toolset will meet the needs of many RFID early adopters. If you have a requirement for a Software Migration Tool not included in this kit, feel free to contact Printronix.
Chapter 1 Hardware/Infrastructure Considerations Hardware/Infrastructure Considerations Once your smart labels have been applied to their target container or pallet you will need external readers to track them through your supply chain. Such readers are typically networked devices that are deployed at key points in the warehouse or distribution center to track incoming and outgoing packages. The readers are managed through a server for gathering and filtering all the RFID information.
Reference Material Useful Industry Web Links Reference Material EPCglobal, Inc. www.epcglobalinc.org Auto-ID Labs www.autoidlabs.org Uniform Code Council, Inc.® www.uc-council.org RFID Journal www.rfidjournal.com Alien Technology® Corporation www.alientechnology.com Applied Wireless Identifications Group, Inc. www.awid.
Chapter 1 Useful Industry Web Links 18
2 Printer Setup Unpacking And Installing The Printer Unpacking The Printer The printer is shipped in a carton and protective bag. Keep all packing material in case shipping is required. CAUTION Avoid touching the electrical connectors to prevent electrostatic discharge damage while setting up the printer. The discharge of accumulated electrostatic energy can damage or destroy the printhead or electronic components used in this device.
Chapter 2 Unpacking And Installing The Printer Removing The Internal Packing Material Remove the tape strips and foam pads from the printer as indicated below. (The top lid of the shipping carton also displays these instructions.
Installation Installation AC Power Receptacle Power Switch 1. Place the printer on a flat level surface that allows easy access to all sides of the printer. CAUTION Never operate the printer on its side or upside down. 2. Make sure the printer power switch is in the Off (O) position. WARNING Failure to properly ground the printer may result in electric shock to the operator. In compliance with international safety standards, this printer has been equipped with a three-pronged power cord.
Chapter 2 Controls And Indicators Controls And Indicators Power Switch The power switch is located on the bottom back panel of the printer. To apply power, place the switch in the | (On) position. When you first power on the printer, a series of initialization messages appears on the Liquid Crystal Display (LCD) on the control panel. To remove power, place the power switch in the O (Off) position.
Description Indicates when the printer is online, offline, or when there is a fault condition. A backlighted liquid crystal display with two rows of 16 characters each. Indicates when the printer is receiving or processing data. Indicator Online Status Liquid Crystal Display (LCD) Job In Process During a fault condition, displays the specific fault message and the corrective action. None Displays “OFFLINE.” During a fault condition, displays the specific fault message and the corrective action.
+ - Button INCREMENT Key in Menu mode TEST PRINT Key Pressing the ↵ (ENTER) key with a Diagnostic Test displayed initiates the test. Pressing ↵ again terminates the test. UP Key in Menu mode FEED Key None Advances the media one label length. None JOB SELECT Key DECREMENT Key in Menu mode Sets printer to Offline mode. Function in Online Mode PAUSE Key Toggles the printer between Online and Offline modes. Description Scrolls through the Test Print patterns.
Button Selects the Menu mode. None Takes the printer Offline and selects the Menu mode. None ENTER Key Pressing the ↵ (ENTER) key in Menu mode selects the displayed option or value. An asterisk then appears next to the option or value indicating it has been selected. Note: If the ENTER key is locked, “ENTER SWITCH LOCKED” displays on the LCD for one second. Press the (DOWN) and ↵ (ENTER) keys at the same time to unlock the ENTER key.
Chapter 2 Loading Media And Ribbon Loading Media And Ribbon IMPORTANT Printronix recommends using the supplied starter roll of 100 labels to set up and verify printer operation. This will avoid expending the more expensive smart labels for this task. CAUTION DO NOT TOUCH the printhead or the electronic components under the printhead assembly. CAUTION Do not close the pivoting deck without label stock installed between the printhead and the platen, because debris on the platen may damage the printhead.
Loading Roll Media Media Roll Media Hanger Media Hanger Guide Media Width Guide Media Damper 3. Slide the media width guide close to the outside end of the media damper. 4. Slide the supplied starter media roll onto and towards the back of the media hanger. 5. Place the media hanger guide under the media hanger and against the lower part of the label core at a 45 degree angle (as shown). This position provides the required tension for a new label roll and the desired drag for a partial label roll.
Chapter 2 Loading Media And Ribbon Media and Ribbon Loading Instructions Media Media Damper Antenna RFID Encoder 6. Raise the media damper. 7. Route the media as illustrated on the media and ribbon loading instructions (or refer to the arrows on the printer frame). NOTE: The media must rest on top of the RFID encoder and the RFID tag must be in proximity of the antenna when the RFID tag is programmed.
Loading Roll Media Lower Media Sensor Media Guard Fixed Guide Media Width Guide Media Damper 8. Lower the media damper. 9. Verify that the left edge of the media is against the fixed guide on the bottom of the media damper. 10. Push the media width guide in until it is flush with the outer edge of the media. 11. Check the horizontal position of the lower media sensor (shown above) and the upper media sensor (shown on page 34). (See “Positioning The Media Sensors” on page 35.
Chapter 2 Loading Media And Ribbon Media (left edge) Platen (left edge) 12. Align the left (inside) edge of the media with the left straight edge of the platen (rubber drive roller). Pivoting Deck Deck Lock Lever 13. Close the printhead by pressing down on the pivoting deck and rotating the deck lock lever fully counterclockwise. 14. Power on the printer (place the power switch in the | position).
Loading Ribbon Loading Ribbon Ribbon Take-Up Core Ribbon Take-Up Spindle Spindle Flange Ribbon Roll Pivoting Deck Ribbon Supply Spindle Deck Lock Lever 1. Install the ribbon take-up core on the ribbon take-up spindle. NOTE: The first ribbon take-up core comes with the printer. Thereafter, use the core from the old (used up) ribbon. 2. Slide the ribbon roll onto the ribbon supply spindle until it stops against the spindle flange. 3.
Chapter 2 Loading Media And Ribbon Printhead Media Rear Ribbon Guide Roller 4. Thread the end of the ribbon under the rear ribbon guide roller, then between the platen and the printhead.
Loading Ribbon Media and Ribbon Loading Instructions Ribbon Take-up Core Ribbon Take-up Spindle 5. Route the ribbon as illustrated on the media and ribbon loading instructions (or refer to the arrows on the printer frame). IMPORTANT Do not attach the ribbon to the ribbon take-up spindle without a ribbon take-up core installed. 6. Attach the ribbon to the ribbon take-up core on the ribbon take-up spindle using the adhesive on the ribbon leader. 7.
Chapter 2 Printing Adjustments Printing Adjustments Right Pressure Block Left Pressure Block Right Pressure Block Pointer Lead Screw Knob Left Pressure Block Handle Bold Mark Printhead Pressure Adjustment Dial Printhead Cover/ Upper Media Sensor Pressure Block Adjustment Scale Printhead Pressure Adjustment Adjust the printhead pressure to the setting of 4.
Positioning The Media Sensors Positioning The Media Sensors Lower Media Sensor Lower Media Sensor Handle (2) Your printer is equipped with upper and lower media sensors that detect the top-of-form position on media with label length indicators (gaps, notches, holes, or black marks). The media sensors also detect Paper Out conditions. Use the handles on the lower media sensor to horizontally position it in the center of the installed media.
Chapter 2 Running Auto Calibrate Running Auto Calibrate Due to manufacturing differences in media and ribbon, the media sensor may have difficulty distinguishing between the label and the liner (gap). To ensure proper operation, you must now run Auto Calibrate: 1. Power on the printer by pressing the power switch. (For the location of the power switch and various panel keys, refer to “Controls And Indicators” on page 22.) 2. Press the .. . key until QUICK SETUP displays.
Positioning The Media Sensors 13. Once the sensed distance value and performance is confirmed, save it to the desired configuration menu as described below before powering off the printer. Saving The Configuration 14. Press the .. . key until QUICK SETUP displays. 15. Press ↑ or ↓ until Save Config./1* displays. 16. Press ↵. Saving Configuration displays briefly.
Chapter 2 QUICK SETUP Menu QUICK SETUP Menu QUICK SETUP Print Intensity -3* -15 to 15 Print Speed 6 ips* 2-10 ips1 Print Mode Transfer* Direct Media Handling Tear-Off Strip* Tear-Off Peel-Off Cut Paper Feed Shift 0.00 inches* 2 -0.50 to X inches3 Label Length 4 or 6 inches* 2, 4 00.1 to 99.0 inches5 Label Width 4.1, 6.6, or 8.5 inches* 2, 4 00.1 to 8.5 inches4 Ver Image Shift 0.00 inches* 2 -1.00 to X inches3 Hor Image Shift 0.00 inches* 2 -1.00 to 1.
QUICK SETUP Submenus QUICK SETUP (cont. from previous page) SMT: Status SMT: Sel Toolset SMT: Select Tool Disabled* Enabled Toolset [1]* Toolset [1] to Toolset [4] EPC1 zEPC2, 3 GTIN1 zGTIN2, 3 UPCA1 zUPCA2, 3 EAN81 zEAN82, 3 EAN131 zEAN132, 3 UCC1281 zUCC1282, 3 Notes: * = Default. 1 Appears only if Toolset [1] is selected under SMT: Sel Toolset. 2 Appears only if Toolset [2] is selected under SMT: Sel Toolset. 3 Undocumented options are reserved for internal use and future design.
Chapter 2 QUICK SETUP Menu Print Speed Specifies the speed in inches per second (ips) at which the media passes through the printer while printing. The range is 2 through 10 ips (in increments of 1 ips). The default is 6 ips. NOTE: The maximum print speed varies based on maximum printer width and dot per inch (dpi) resolution of the printhead installed (203 or 300 dpi). Print Mode Specifies the type of printing to be done. • • Transfer. Indicates Thermal Transfer printing (ribbon installed). Direct.
QUICK SETUP Submenus • Cut. When the optional media cutter is installed, it automatically cuts media after each label is printed or can cut after a specified number of labels have been printed using a software cut command. It cuts continuous roll paper, labels, or tag stock. NOTE: This feature is currently not supported using the RFID encoder. • Continuous. Printer prints on the media and sends it out the front. The default is Tear-Off Strip.
Chapter 2 QUICK SETUP Menu Label Width The allowable range in inches is 00.1 to the maximum print width of the printer. The allowable range in millimeters is 2.5 to the maximum width of the printer. Ver Image Shift Specifies the amount to shift an image up (-) or down (+) for precise positioning on the label. The actual height of the image is not affected by this parameter. The allowable range is -1.00 inches to the current Label Length value setting, up to a maximum of 12.80 inches in 0.
QUICK SETUP Submenus • Inv. Portrait. Inverse Portrait refers to vertical page orientation, where the height of a page is greater than its width. The top edge of the image is parallel to the trailing edge of the media. The following example is viewed from the front of the printer. Trailing Edge 4” FEED The top edge of the image is parallel to the trailing edge of the media. 6” Leading Edge • Landscape. Landscape refers to horizontal orientation, where the width of a page is greater than its height.
Chapter 2 QUICK SETUP Menu • Inv. Landscape. Inverse Landscape refers to horizontal orientation, where the width of a page is greater than its height. The top edge of the image is parallel to the right edge of the media. The following example is viewed from the front of the printer. 4” The top edge of the image is parallel to the right edge of the media.
QUICK SETUP Submenus • Advanced Gap. Select when using media that has liner gaps between die cut labels with black background. The top-of-form position is the leading edge of the die cut label (trailing edge of the gap, notch, or hole). • Advanced Notch. Select when using media with notches or holes that interrupt a black vertical line on the underside of the media. The top-of-form position is the leading edge of the die cut label (trailing edge of the gap, notch, or hole). The default is Disable.
Chapter 2 QUICK SETUP Menu Power-Up Config. You can specify one of the eight configurations as the power-up configuration. The default is Factory. SMT: Status See “Software Migration Tools (SMT)” on page 65. • Disabled.The printer disables the use of the Software Migration Tools. • Enabled. The printer enables the use of the Software Migration Tools. SMT: Sel Toolset See “Software Migration Tools (SMT)” on page 65. • • • Toolset [1]. SMTs for PGL® emulation. Toolset [2]. SMTs for PPI1 emulation.
QUICK SETUP Submenus For More Information This chapter has provided general information for use of your printer. The next chapter provides information about the RFID encoder.
Chapter 2 For More Information 48
3 Smart Label Development Overview This chapter describes how to use the RFID encoder. The RFID encoder is designed to be transparent to the printer operation. It provides the capability of programming smart labels (with embedded RFID tags) while printing the label format. The smart labels are provided with the printer or purchased separately from Printronix.
Chapter 3 RFID CONTROL Menu RFID CONTROL Menu RFID CONTROL RFID Reader Tag Type Enable* Disable Alien Squig 64* Alien Squig 96 RAF Omni 313 64 Alien M-TAG 64 RAF Omni 313 96 Error Handling Overstrike* None Label Retry 10* 1 to 10 Max Retry Error Enable* Disable Alien M-TAG 96 Matrics X2020 96 Stop Tag Write Cnt1 Notes: * = Default. Failed Tag Cnt1 Italicized items are available only when you enable Admin User in the PRINTER CONTROL menu. Clear Tag Stat 1 Display item only.
RFID CONTROL Submenus RFID CONTROL (cont. from previous page) Custom Tag Len 8* 8 to 32 Custom Tag Class Class 1* Class 0 Class 0+ Notes: * = Default. Italicized items are available only when you enable Admin User in the PRINTER CONTROL menu. RFID CONTROL Submenus RFID Reader This menu item enables or disables the RFID encoder. The default is Enable. Error Handling This menu item selects the error handling mode for RFID failures. The default is Overstrike.
Chapter 3 RFID CONTROL Menu Label Retry NOTE: Label Retry only applies when the Error Handling mode is set to Overstrike. This menu item selects the number of label retries that the RFID encoder will attempt before declaring a fault. This may indicate a problem with the RFID encoder, the antenna assembly, the printer setup, or the label stock. The default is 10. Max Retry Error This menu item enables or disables the Max Retry Error menu item.
RFID CONTROL Submenus Precheck Tags When this menu item is set to Enable, the RFID encoder checks the tags for a pre-programmed quality code. If the code is absent, the tag immediately fails and the selected Error Handling mode is performed (Overstrike, None, or Stop). The default is Disable. Overstrike Style This menu item selects the style of the overstrike pattern. The default is Grid. When it is set to Grid, a grid pattern prints when it overstrikes.
Chapter 3 RFID CONTROL Menu Admin User Menu Items To see these menu items, set Admin User to Enable in the PRINTER CONTROL menu. (Refer to the User’s Manual.) IMPORTANT Admin User menu items should only be used for troubleshooting. Tag Type This menu item selects the tag type in use. The default is Alien Squig 64. Other classes may be added in the future. IMPORTANT If you have a T5000e printer, do not use Alien M-TAG 64, Alien M-TAG 96, or Matrics X2020 96.
Admin User Menu Items When Custom Tag is set to Disable, the settings in the custom tag menus are ignored by the RFID encoder. When it is set to Enable, the RFID encoder uses the settings in the custom tag menus, which must be set to match the characteristics of the custom tag. When it is set to Duplicate, the settings of the selected Tag Type menu item are copied into the custom tag menus. Custom Pwr Set NOTE: To enable this menu item, set Custom Tag to Enable.
Chapter 3 RFID PGL Commands RFID PGL Commands Write Tag Purpose To program non-incremental data into an RFID tag (embedded in the smart label). MODE CREATE Format RFWRITE;[HEX;][EPCm;][RFn;L;][LOCK;]ATp;[(D)datafield(D)] RFWRITE; The RFID Write Tag command. HEX; Optional parameter to indicate that the text in datafield is in hexadecimal format and that it will be converted to binary format. EPCm; Optional parameter to indicate that the data in datafield should be converted to an EPC number.
Read Tag datafield is ignored, and dynamic data must be entered via the RF command in the EXECUTE mode. The length of the dynamic data must be equal to L. LOCK; Optional parameter to write-protect the data. Currently not supported. ATp; p specifies the decimal start position where data will be written to the tag. Subsequent bits will be shifted and previous bits are nulled. (D) Delimiter designating the start and end of static data for the RFWRITE field.
Chapter 3 RFID PGL Commands length The decimal number that specifies the length of the data to be read. format Replace the optional format parameter with any non-zero number to convert the data to hexadecimal format. EPC Programming Example This programming example shows reading and writing dynamic EPC data to a tag. ~CREATE;HEX;431 //Create a form named HEX. RFWRITE;HEX;RF3;16;AT1; //Write Tag with data from dynamic RFID element 3. //Length of data is 16, format is HEX.
ASCII Programming Example ASCII Programming Example This programming example shows reading and writing dynamic ASCII data to a tag. ~CREATE;READTAG //Create a form named READTAG. RFWRITE;RF3;8;AT1; //Write Tag with data from dynamic RFID element 3. //Length of data is 8. ALPHA //The following ALPHA element is defined below. //It will print the contents of the tag. RFREAD@;AF1;8;10;10;0;0 //Read Tag Indicator character is “@”. Incorporate read //data into Dynamic ALPHA field number 1.
Chapter 3 RFID PPI1 Commands RFID PPI1 Commands Get Tag Unique ID Purpose Read the unique identification number of the RFID tag (embedded in the smart label). Format ^RI x ^RI Get Tag Unique ID command. x The field number to which the data will be assigned. The default is 0, and other acceptable values range from 1 to 9999. Comments The PPI1 only supports Alien Technology Class 1a tags, which do not have the unique identification numbers. Therefore, the PPI1 absorbs this command.
Read Tag Read Tag Purpose This command allows data from the RFID tag (embedded in the smart label) to merge into any previously defined dynamic data field. It is equivalent to the Field Number command (^FN) except that the data come from the RFID tag. Format ^RT x, start, length, hex, retries, motion, reserved ^RT Read Tag command. x Specified Field Number. The default is 0. The acceptable value range is 1 to 9999. start Location where data will be read from the RFID tag.
Chapter 3 RFID PPI1 Commands motion Set this flag to 1 to read data from the tag without moving the label. The printer may adjust the label position while it reads data from the tag, but this adjustment will reverse before any subsequent normal label movement. Even if this flag is set to 1, other commands (i.e., alpha or barcode) may move the label. reserved This is a reserved flag. The PPI1 absorbs this number. Comments This command is only executed by the demand for data from any dynamic field.
Host Verification Even if this flag is set to 1, other commands (i.e., alpha or barcode) may move the label. protect This flag indicates whether the data should be protected from being overwritten later. The default is 0, meaning the data are not protected. Other acceptable values are 1 to 255, meaning the data are protected using this number as the LOCK password. reserved This is a reserved flag. The PPI1 absorbs this number.
Chapter 3 RFID PPI1 Commands EPC Programming Example ^XA //Begin ZPL form. ^WT0^FH^FD_68_65_6C_6C_6F_74_61_67^FS //Write Tag with data = “68656C6C6F746167” //(hex format). ^RT1,0,1,1^FS //Read Tag into data element 1, 16 characters long //(hex format). ^FO100,100^A0N,60^FN1^FS //Print data in element 1. ^XZ //End and print label.
Tools List Software Migration Tools (SMT) There are SMTs for six separate end-use applications supporting both PGL and PPI1 datastreams for a total of 12 tools. Each tool intercepts bar code data in a host datastream and copies the data to an RFID tag (embedded in a smart label) according to a set of rules as defined below. SMTs assume that only one bar code of the type being processed is present. In the event that there is more than one of a given type of barcode present, only the first is processed.
Chapter 3 Software Migration Tools (SMT) • EAN8: Copies data from an EAN8 bar code to an RFID tag. EAN 8+2 and EAN 8+5 variants are both supported. Data written to the RFID tag is right justified and zero padded. Checksum data calculated by the printer is not encoded onto the RFID tag. • EAN13: Copies data from an EAN13 bar code to an RFID tag. EAN 13+2 is also supported but EAN 13+5 variant is not supported. Data written to the RFID tag is right justified and zero padded.
Selecting The Tools Selecting The Tools 1. Press .. . until QUICK SETUP displays. 2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key. 3. Press ↓ until SMT: Sel Toolset displays. 4. Press ↓ until Toolset [1] (PGL emulation) or Toolset [2] (PPI1 emulation) displays. 5. Press ↵ to select it. 6. Press ↓ until SMT: Select Tool displays. 7. Press ↓ until the desired tool displays. 8. Press ↵ to select it. 9.
Chapter 3 Error Messages Error Messages The RFID encoder can detect a number of errors. When one of these errors occurs, the RFID encoder alerts the printer to perform the currently selected error action (see “Error Handling” on page 51) and display the appropriate error message on the control panel’s LCD (see Table 2). Table 2.
Troubleshooting If you are having trouble with the RFID encoder, consult Table 3 for a list of symptoms and possible solutions. Table 3. Troubleshooting the RFID Encoder Symptom No communication between the printer and the reader Solution 1. Make sure the serial interface adapter and the serial cable are plugged into the printer. See “Installation” on page 21. 2. Make sure Reader = Enable in the RFID CONTROL menu. 3.
Chapter 3 Troubleshooting Table 3. Troubleshooting the RFID Encoder Symptom The RFID encoder works, but it does not meet expectations 70 Solution Make sure that both Error Handling and Label Retry are set to desired values in the RFID CONTROL menu.
Index A Auto Calibrate option, 45 running, 36 Auto Retry, 54 Error messages, printed overstrike Precheck Fail x / Check media, 53 Tag Comm Err x / Check cable, 53 Tag R/W Err x / Check media, 53 F B Barcode demo test, 37 C Characteristics, smart labels, 13 Clear Tag Stat, 52 Configuration, saving, 37 Control panel, 22 Control panel error messages, 68 Custom Pwr Set, 55 Custom Tag, 54 Custom Tag Class, 55 Custom Tag Len, 55 E EPC programming example PGL, 58 PPI1 (ZPL), 64 Error Handling, 51 Error messag
Index M Max Retry Error, 52 Media Handling option, 40 Media sensor, positioning, 35 Media, roll, 26 O Online Status indicator, 22 Ordering smart labels, 15 Orientation option, 42 Overstrike Style, 53 Overstruck smart labels, 13 Overview, smart label development, 49 P Paper Feed Shift option, 41 PGL commands, 56 Positioning the media sensor, 35 Power switch, 22 Power-Up Config.
Index Set Tag Type PPI1 command code, 60 Smart labels, 49 characteristics, 13 development overview, 49 ordering, 15 overstruck smart labels, 13 performance, 12 reading See Reading a tag SMT Sel Toolset option, 46 Select Tool option, 46 Status option, 46 Software Migration Tools (SMT), 65 introduction, 14 selecting, 67 tools list, 65 T Tag Comm Err x / Check cable, 53 Tag R/W Err x / Check media, 53 Tag Type, 54 Tag Write Cnt, 52 Tags, RFID See Smart labels Troubleshooting, 69 U Unpacking the printer, 19
Index 74
For technical assistance, contact your Distributor/VAR/Reseller for service. For further assistance, contact the Printronix Customer Support Center. Printronix Customer Support Center Americas 1-714-368-2686 Europe, Middle East, and Africa (31) 24 6489 410 Asia Pacific (65) 65484114 Web site: http://www.printronix.com/public/servicessupport/default.aspx Printronix Supplier Center Americas 1-800-733-1900 Europe, Middle East, and Africa 33.1.46.25.
