978461de 28-09-2001 8:49 Pagina 1 Geschirrspüler 4300 Standmodell Gebrauchsanweisung
978461de 28-09-2001 8:49 Pagina 2 Inhaltsverzeichnis Seite Wirtschaftlich und umweltbewusst spülen . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Aufstellung / Anschluss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Wasserzulauf . . .
978461de 28-09-2001 8:49 Pagina 3 Sehr geehrte Kundin, sehr geehrter Kunde, Wichtige Informationen und Hinweise Damit Ihnen die Bedienung leicht fällt, haben wir eine ausführliche Gebrauchsanweisung beigelegt. Bitte lesen Sie auch vor Inbetriebnahme die im separaten Heft vorhandenen Informationen und Hinweise. Sie soll Ihnen helfen, schnell mit Ihrem neuen Gerät vertraut zu werden. Wir wünschen Ihnen viel Freude mit Ihrem neuen Geschirrspüler.
978461de 28-09-2001 8:49 Pagina 4 Gerätebeschreibung Wasserablaufschlauch Drucktasten Ein/Aus -Taste Türgriff LSPRIV125 Anzeigeelemente Stromanschlußkabel Arbeitsplatte Wasserzulaufschlauch Höhenverstellbare Füße Arbeitsplatte Geschirrkorbarretierung oberer Geschirrkorb oberer Sprüharm unterer Sprüharm Salzbehälter Feinsieb Grobsieb Behälter für Reiniger Behälter für Klarspüler Typenschild Bedienblende priv27 4
978461de 28-09-2001 8:49 Pagina 5 Installation Aufstellung/Anschluss Verpackungsteile entfernen Dieser Geschirrspülautomat wird anschlussfertig, also mit Kabel und Stekker, Wasserzulaufschlauch und Wasserablaufschlauch, geliefert. Er kann ohne Sonderinstallation in Betrieb genommen werden, wenn am Aufstellungsort eine vorschriftsmäßig installierte Schutzkontakt-Steckdose, ein Wasserzulauf und ein Wasserablauf vorhanden sind.
978461de 28-09-2001 8:49 Pagina 6 Bitte wenden Sie sich an den Kundendienst, wenn der Wasserdruck höher als 10 bar = 10 atü ist (dann ist der Einbau eines Druckminder ventils nötig) oder niedriger als 1 bar = 1 atü. Nach jedem Spülprogramm ist der Wasserhahn zu schließen! Schlauchlänge Der Ablaufschlauch wird zweckmäßigerweise fest installiert. Die Abflußhöhe muss zwischen 30 und 100 cm liegen. Genügender Abflussquerschnitt muss gewährleistet sein.
978461de 28-09-2001 8:49 Pagina 7 Verlegen der Schläuche Tür öffnen und schließen Wasserzu- und -ablaufschlauch sind weitgehend knickfrei. Überzeugen Sie sich davon, dass auch beim Einschieben des Spülers an seinen endgültigen Platz, die Schläuche nicht geknickt oder gequetscht werden und nach den Seiten im Sockelrücksprung verlegt sind. Besondere Vorschriften des örtlichen Wasserwerkes sind genauestens zu beachten.
978461de 28-09-2001 8:49 Pagina 8 Beschreibung der Bedienungsblende 12 1 Betriebskontrolllampe Die Kontrolllampe leuchtet, wenn das Gerät am Stromnetz angeschlossen ist und die EIN/AUS-Taste gedrückt wird. Sie zeigt an, dass das Gerät betriebsbereits ist. 2 EIN/AUS-Taste Einschalten Nach dem Drücken dieser Taste leuchtet die Betriebslampe (1) und zeigt an, dass die Maschine unter Spannung steht und die Auswahl der Programme vorgenommen werden kann.
78461de 28-09-2001 8:49 Pagina 9 7 Salz-Nachfüllanzeige Die Enthärtungsanlage ist mit einer elektrischen Salzanzeige ausgestattet. Wenn die Kontrolllampe “SALZ” leuchtet, muss Salz nachgefüllt werden. ziehen. Bei Festanschluss: Sicherung ausschalten bzw, herausdrehen. Zur Fehlermeldung den Kundendienst anrufen. 8 Programmablauf-Anzeige • Wenn das Programm angelaufen ist, wird der jeweilige aktuelle Programmschritt angezeigt, der gerade abgearbeitet wird. • Am Programmende leuchtet die Lampe ENDE.
978461de 28-09-2001 8:49 Pagina 10 Spülprogramm Spülprogramm starten 1. Überprüfen Sie, ob Geschirr und Besteck im Geschirrspüler so eingeordnet sind, dass die Sprüharme sich frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. Tür schließen. 4. EIN/AUS-Taste drücken, Anzeige der EIN/AUS-Taste leuchtet. 5. Programmtaste für das gewünschte Programm drücken (siehe “Programmtabelle”. Programmanzeige leuchtet. Nach ungefähr 6 Sekunden beginnt das gewählte Spülprogramm.
978461de 28-09-2001 8:49 Pagina 11 Bedienung / Handhabung Wasserenthärtung Hat Ihr Leitungswasser eine Härte von 5° dH und mehr, muss das Wasser unbedingt enthärtet werden, um Kalkablagerungen am Geschirr und in der Maschine zu vermeiden. Über Wasserhärte und Härtebereich in Ihrem Wohngebiet informiert Sie das zuständige Wasserwerk. Zur Wasserenthärtung muss der Salzbehälter der serienmäßig eingebauten Enthärtungsanlage immer mit Regeneriersalz gefüllt sein.
978461de 28-09-2001 8:49 Pagina 12 Wasserhärte in °dH1) Anzahl der Blinkzeichen unter 4 1 x blinken 4-18 2 x blinken 19-29* 3 x blinken 30-40 4 x blinken 41-50 5 x blinken Wasser abgepumpt. Die Salzmenge reicht für 20-30 Spülprogramme. Marken-Regeneriersalz für Geschirrspülautomaten verwenden. Salznachfüll-Anzeige 1) (°dH) Deutscher Härtegrad, Maß für die Wasserhärte * werkseitige Einstellung 7.
978461de 28-09-2001 8:49 Pagina 13 Klarspüler Klarspüler nachfüllen Es dürfen nur Klarspüler verwendet werden, die speziell für Haushaltsgeschirrspülautomaten geeignet sind. Der Klarspüler sorgt dafür, dass das Geschirr einwandfrei und fleckenlos trocknet. Er wird aus dem Vorratsbehälter automatisch dosiert. Der im Inneren der Tür eingebaute Behälter hat ein Fassungsvermögen von ca. 110 ml, das je nach eingestellter Dosierung für 16-40 Spülgänge ausreicht.
978461de 28-09-2001 8:49 Pagina 14 Reiniger Es dürfen nur Reiniger verwendet werden, die speziell für Haushaltsgeschirrspülautomaten geeignet sind. Es spielt dabei keine Rolle, ob die Reiniger flüssig, pulver- oder tablettenförmig sind. Die Wirkungsweise der verschiedenen Reiniger ist unterschiedlich. Beachten Sie deshalb bitte grundsätzlich die Dosierempfehlungen des Reinigerherstellers.
978461de 28-09-2001 8:49 Pagina 15 Geschirr vorbereiten Einordnen im unteren Korb Alle harten Speisereste entfernen, z.B. Knochen, Gräten, Obstkerne - auch grobe Reste wie z.B. Kartoffelrückstände, Breireste, Spinat, Kaffee- und Teesatz, Salatblätter, Obstschalen, Kaugummi. Angesetzte Speisereste mit Wasser anweichen, evtl. etwas Reiniger zugeben. Es ist wirtschaftlich, erst dann mit einem vollen Programm zu spülen, wenn der Spüler ganz gefüllt ist.
978461de 28-09-2001 8:49 Pagina 16 Besteckkorb: Messer, Gabeln und Löffel mit dem Griff nach unten stellen. Gebrauchsflächen der Löffel nicht ineinander legen. Sehr lange Löffel und langstielige Teile besser in den Oberkorb legen. Der Gitteraufsatz am Besteckkorb kann auch abgenommen werden, wenn es erforderlich ist. Dessertteller bis zu einem Durchmesser von 20 cm eingeordnet. Gläser mit langem Stiel können umgedreht in den höheren Tassenfächern eingehängt werden.
978461de 28-09-2001 8:49 Pagina 17 ● Oberen Korb ganz herausziehen, umsetzen in die unteren Korbrollen und wieder einschieben. ● Arretierungen (A) wieder nach vorne drehen. A RC01 Vor dem Spülen überprüfen ● Sind alle Geschirrteile richtig eingeordnet? Das ist besonders bei leichten Teilen wichtig, damit sie bei der intensiven Wasserumwälzung ihren Stand sicher behalten. ● Stehen die einzelnen Teile frei? Berührungsstellen können das einwandfreie Spülen beeinträchtigen.
978461de 28-09-2001 8:49 Pagina 18 Kurzanweisung Die wichtigsten Handgriffe bei der Inbetriebnahme des Gerätes sind folgende: 1. Wasserzulauf- und -ablaufschlauch anschließen. 2. Netzstecker in die Steckdose einstecken. 3. Wasserhahn öffnen. 4. Wasserhärtebereich einstellen. 5. Klarspüler und Salz einfüllen. 6. Geschirrspülerkörbe füllen und wieder einschieben. 7. Reiniger dosieren. 8. Tür schließen. 9. EIN/AUS-Taste drücken. 10. Programmtaste drücken. Das Spülprogramm läuft an.
978461de 28-09-2001 8:49 Pagina 19 Wartung und Pflege Siebeinsätze reinigen Feinsieb Grobsieb Das großflächige Feinsieb (B), muss bei sichtbaren Ablagerungen gereinigt werden. Da das Grobsieb weitgehend selbstreinigend ist, prüfen Sie bitte einmal pro Woche ob sich dort evtl. Speisereste abgelagert haben. 90° B C A MA05 MA04 ● Fassen Sie das Sieb (A) am Griff an und ziehen es nach oben heraus. ● Reinigen Sie das Sieb unter fließendem Wasser.
978461de 28-09-2001 8:49 Pagina 20 Oberer Sprüharm: Zu seiner Reinigung ist der obere Sprüharm vom Wassersammelrohr abzunehmen. Dazu wie folgt vorgehen: - den oberen Geschirrkorb herausziehen; - den Sprüharm nach oben drücken und gleichzeitig durch Drehen im Uhrzeigersinn abschrauben. Den Sprüharm wieder montieren, indem er nach oben gedrückt und gleichzeitig bis zu seiner Blockierung gegen den Uhrzeigersinn eingeschraubt wird. Den Sprüharm loslassen und prüfen, ob er sich ungehindert drehen kann.
978461de 28-09-2001 8:49 Pagina 21 Technische Daten / Abmessungen Technische Daten: Abmessungen: Fassungsvermögen Heizung Ablaufpumpe Umwälzpumpe Spannung Gesamthöhe Höhe ohne Arbeitsplatte Gesamtbreite Gesamttiefe Tiefe ohne Arbeitsplatte Gewicht 12 Maßgedecke 2100 Watt 200 Watt 200 Watt 230 Volt 50 Hz Absicherung 10 Ampere Gesamtanschluss 2300 Watt Wasserdruck mindestens 1 bar Wasserdruck maximal 10 bar Energieeffizienz A Reinigungswirkung B Trockenwirkung C 850 mm 820 mm 600 mm 610 mm 585 m
978461de 28-09-2001 8:49 Pagina 22 Unterbau des Gerätes Arbeitsplatte entfernen Der Geschirrspülautomat lässt sich auch unter eine vorhandene Tischplatte oder unter eine Spülenabdeckung einbauen; hierzu brauchen Sie nur die beiden hinteren Befestigungsschrauben der Arbeitsplatte zu lösen. Arbeitsplatte von hinten nach vorn herausziehen und abheben. Die Höhe und die Nivellierung durch die Schraubfüße einstellen und das Gerät einbauen.
978461de 28-09-2001 8:49 Pagina 23 Notizen 23
978461de 28-09-2001 Notizen 24 8:49 Pagina 24
978461de 28-09-2001 8:49 Pagina 25 Maßgedecke Fassungsvermögen Oberkorb Das Gerät fasst 12 internationale Maßgedecke plus Ser viergeschirr nach EN 50242. 12 Suppenteller 12 flache Teller 12 Dessertteller 12 Teetassen 12 Untertassen 12 Trinkgläser 12 Messer 12 Gabeln 12 Löffel 12 Teelöffel 12 Dessertlöffel 1 runde Schüssel 1 runde Schüssel 1 ovale Platte 1 Schale 1 Vorlegegabel 2 Vorlegelöffel 1 Soßenlöffel ca. 23 cm Ø ca. 26 cm Ø ca. 19 cm Ø ca. 9 cm Ø, ca. 0,2 l ca. 14 cm Ø ca. 7 cm Ø, ca.
978461de 28-09-2001 8:49 Pagina 26 Programmübersicht Programm NORMAL 65° SPAR 65° 1) NORMAL BIO 50° * RAPID 50° Art und Ausmaß der Verschmutzung Zu drückende Geschirrart Tasten Stark verschmutztes Geschirr mit anhaftenden, vorwiegend stärkehaltigen Speiseresten (z.B. Nudeln, Reis, Grieß, Kartoffeln, Eier, Soße, Bratfleisch). Töpfe und verschiedenartiges Geschirr EIN AUS NORMAL 65° Normal oder stark verschmutztes Geschirr mit anhaftenden, vorwiegend stärkehaltigen Speiseresten (z.B.
978461de 28-09-2001 8:49 Pagina 27 Programmablauf und Verbrauchswerte Spülmittelmenge ** auf dem im Behälter Behälterdeckel 25 g 30 g 25 g 30 g Verbrauchswerte *** Programmablauf Strom kWh Wasser Liter Zeit Minuten 10 g Vorspülen 55°C Hauptspülen 65°C 2 Klarspülgange kalt 1 Klarspülgang 65°C Aktivtrocknung 1,94 22 95-105 / Vorspülen kalt Hauptspülen 65°C 1 Klarspülgang kalt 1 Klarspülgang 65°C Aktivtrocknung 1,40 18 90-100 5g Vorspülen kalt Hauptspülen 50°C 1 Klarspülgang kalt 1 Klars
-09-2001 8:49 Pagina 28 Geschirrspüler 4300 Standmodell weiß Produkt-Nr. 919.