Specifications

26
Crown Ampliers Non-Networkable
amplifiers
stand alone
Low Impedance Only
XLS Series Minimum
Guaranteed Power
XLS
202
XLS
402
XLS
602
XLS
802
XLS 5000
Per channel, both channels driven 1 kHz with 0.5% THD
Stereo, 2 ohms (per ch.)
Stereo, 4 ohms (per ch.)
Stereo, 8 ohms (per ch.)
Bridge-Mono, 8 ohms
Bridge-Mono, 4 ohms
__
300W
200W
600W
__
__
450W
300W
900W
__
__
600W
380W
1,200W
__
__
800W
500W
1,600W
__
2,500W**
1,800W*
1,100W*
3,600W*
5,000W**
*With 0.1% THD (Total Harmonic Distrotion)
**With 1% THD (Total Harmonic Distrotion)
Reliable design •
Rugged, all-steel 2U chassis (3U for XLS 5000) •
Efficient fans forced cooling•
Electronically balanced XLR inputs•
Touchproof binding post and Speakon•
®
outputs
Precision detented level controls•
Signal, clip and fault LEDs •
3 Year, No Fault Warranty•
Crown’s XLS Series power amplifiers
TECH-TIPS
Can I connect a 70v rated loudspeaker to a 100v line system?
Yes. 70v and 100v systems are both constant voltage systems. The only difference being the maximum RMS voltage on the line (100v or 70v). 70v is 3dB
down from 100v, which when converted to power, conveniently equals half power. So a 100v speaker connected to a 70v line system will draw HALF its rated
power. Conversely a 70v speaker connected to a 100v line system will draw DOUBLE its power.
All you need to do is select the appropriate tap. For example:
1. You wish to connect 70v speaker to a 100v line system and set it to 10w. Select the 5w tap.
2. You wish to connect a 100v speaker to a 70v line and set it to 20w. Select the 40w tap
Please observe the maximum rated power of the loudspeaker and take care to avoid overloading the speaker. E.g. if you have a 70v speaker rated at 60w
max and you wish to connect to a 100v line, do NOT select the 60w tap as this will draw 120W @ 100v. Select the 30w tap for maximum power.
The Crown XLS202D and
XLS402D are ideal for lower
power, low impedance
applications. Perfect for the
entire JBL Control Contractor
range.
tips
guide
Refer pages
27 32
Integrated proprietary DSP with LCD front panel •
display
Accurate, uncoloured sound with very low distortion •
Advanced protection circuitry •
Extremely versatile, handling a wide range of •
speaker impedances and outputs
Switch-mode universal power supply •
Speaker presets for crossover frequencies, EQ, •
limiting, and delay
All products fill 2U rack spaces and weigh under •
8kgs
Speakon•
®
and binding post outputs, XLR inputs
and loop-thrus
Comprehensive LED status per channel •
3 Year, No Fault Warranty•
Crown’s XTi Series amplifiers
XTi Series Minimum Guaranteed
Power, 1kHz
XTi 1000 XTi 2000 XTi 4000 XTi 6000
Per channel, both channels driven 1 kHz with 0.5% THD
Stereo, 2 ohm Dual (per ch.)
Stereo, 4 ohm Dual (per ch.)
Stereo, 8 ohm Dual (per ch.)
Bridg-Mono, 4 ohm Bridge-Mono
Bridg-Mono, 8 ohm Bridge-Mono
700W*
500W
275W
1,400W*
1,000W
1,000W*
800W
475W
2,000W*
1,600W
1,600W*
1,200W
650W
3,200W*
2,000W
3,000W*
2,100W
1,200W
6,000W*
4,200W
*With 1% THD (Total Harmonic Distrotion)