Installation guide

ManualsBrandsPro-face ManualsConsumer electronicsGP4105W1D

GP-4100 Series

Installation Guide

GP-4100 Series Connection Types

Package Contents

(1) GP Unit (1)

(2) Installation Guide (1) <This Guide>

(3) Warning/Caution Information (1)

(4) Installation Gasket (1, attached to the GP unit)

(5) Installation Fasteners (Set of 2)

(6) COM I/F Connector (1)

(For RS-232C and RS-422/485 types)

(7) DC Power Supply Connector (1)

(For the Ethernet type and a portion of models

)

(Attached to unit)

*1 Not included with models that have the following

type of power connector.

This unit has been carefully packed, with special

attention to quality. However, should you find any-

thing damaged or missing, please contact your local

GP distributor immediately.

About the Manual

This manual describes wiring and installation

procedures. For more detailed information, refer to

the manuals indicated below.

The manuals can be selected from the help menu of

GP-Pro EX or downloaded from Pro-face Home Page.

Global Code

A global code is assigned to every Pro-face product as

a universal model number.

For more information on product models and their

matching global codes, please refer to the following

URL.

http://www.pro-face.com/product/globalcode.html

Please read the "Warning/Caution

Information" on the attached sheet

before using the product.

RS-232C type

GP4105G1D

GP4105W1D

RS-422/485 type

GP4106G1D

GP4106W1D

RS-485 (isolation) type

GP4107G1D

GP4107W1D

Ethernet type

GP4104G1D

GP4104W1D

Manual Contents

GP-4100 Series

Hardware

Manual

Specifications, dimensions,

accessories, system design, overseas

standards, and other details.

Device/

PLC Connection

Manual

System configuration of connected

devices (PLCs and other devices),

communication settings examples,

connection wiring diagram, and

other details.

Maintenance/

Troubleshooting

• Troubleshooting

Help for solving problems.

• Maintenance

Details on the GP unit’s Offline Mode

URL

http://www.pro-face.com/otasuke/

Summary of content (8 pages)

PAGE 1
This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or missing, please contact your local GP distributor immediately. GP-4100 Series Installation Guide About the Manual Please read the "Warning/Caution Information" on the attached sheet before using the product. This manual describes wiring and installation procedures. For more detailed information, refer to the manuals indicated below.
PAGE 2
Ethernet type Electrical Specifications A GP4104* GP4106* GP4107* GP4105* Input Voltage DC24V Rated Voltage DC19.2 to 28.8V Allowable 3ms or less Voltage Drop 6.0 W or 6.2 W or 6.5 W or less less less Power Consumption 2.7 W or 3.0 W or 3.
PAGE 3
Communications Cable Specifications External Interfaces Communications 0.14 to 1.5mm2 Cable Diameter*1 (28 - 16 AWG) Conductor Type • For instructions on how to connect to other devices, always refer to the "GP-Pro EX Device/ PLC Connection Manual". 1. Simple or Stranded Wire*2 Conductor Length 7mm [0.28in] Serial Interface • For detailed information on pins, refer to the GP4100 Series Hardware Manual. • The serial interface of the RS-232C and RS-422/ 485 types is not isolated.
PAGE 4
RS-485 (isolation) type D-Sub 9-pin socket type connector Pin Connection 1 5 RS-485 (isolation) type PIN # 6 9 NC 2 NC Panel Face 3 LINE(+) 4 RS(RTS) 5 SG*1 6 5V*2*3 7 NC 8 LINE(-) 9 (GP unit side) Signal Name 1 • Be sure that heat from surrounding equipment does not cause the GP to exceed its standard operating temperature. 2. GP Installation (1) Cut a hole in the panel according to the GP unit panel cutout dimensions. X r≤3 [0.
PAGE 5
• When mounting the GP unit vertically, ensure that the left side of the unit faces up (i.e. the power connector and serial interface should be at the bottom). • Tightening the screws with too much force can damage the GP unit’s plastic case. • In order to guarantee water repelling effect the necessary torque is 0.52N•m [4.60Lb•in]. Wiring • If the power connector is the following type, please read "1. Wiring the Power Cord No.1".
PAGE 6
1. Wiring the Power Cord No.1 2. Power Cord Specifications Power Cord Specifications Use copper conductors only. Power Cord Diameter Conductor type Wiring the Power Cord No.2 • Use copper conductors only. 1.5mm2 2 Simple Wire: 0.75 to Stranded Wire: 0.75 to 1mm (18 - 16 AWG) Power Cord Diameter Conductor type Simple or Stranded Wire*1 5mm [0.2in] Conductor Length 0.75 to 1.5mm2 (18 - 16 AWG) Simple or Stranded Wire*1 7mm [0.
PAGE 7
3. Wiring Cautions UL/c-UL Approval Improving Noise/Surge Resistance Be aware of the following items when building the GP unit into an end-use product: • For use on a flat surface of a Type 4X (Indoor Use Only) and/or Type 13 Enclosure. • The temperature rating of field installed conductors: 75°C only. • Must be used with a Class 2 Power Supply. (24 VDC) • For use in Pollution Degree 2 environment, or equivalent. • Surrounding air temperature rating 50°C maximum or equivalent.
PAGE 8
Isc = 0.7 A Ca = 16 µF La = 10 µH 2. Selected Associated Nonincendive Field Wiring Apparatus shall satisfy the following: Associated Nonincendive Field Wiring Apparatus for USB (Type A) interface of the GP-4100 Series - Voc ≤ Vmax Isc ≤ lmax Ca ≥ Ci + C cable La ≥ Li + L cable Inquiry Do you have any questions about difficulties with your GP? Please access our site anytime that you need help with a solution. http://www.pro-face.com/otasuke/ Nonincendive Field Wiring Apparatus 3.