Installation guide

ManualsBrandsPro-face ManualsComputer equipmentLT Series

LT-3200 Series

Installation Guide

Package Contents

(1) LT Unit (1)

(2) English and Japanese Installation Guides

(one of each) <This Guide>

(3) Warning/Caution Information (1)

(4) English and Japanese EX Module

Hardware Manual

(1)

(5) Installation Gasket (1, attached to the LT

unit)

(6) Installation Fasteners (Set of 4)

(7) DIO Connector (1)

(8) Power Connector (1)

(9) USB Cable Clamp (1 set)

(Holder: 1, Cover: 1)

This unit has been carefully packed, with

special attention to quality. However, should

you find anything damaged or missing,

please contact your local LT distributor

immediately.

About the Manual

For the detailed information on LT3000

series, refer to the following manual.

• LT3000 Series Hardware Manual

• Maintenance/Troubleshooting

• GP-Pro EX Reference Manual “Con-

trolling External I/O”

LT3000 Series Hardware Manual can be

selected from the help menu of GP-Pro EX or

downloaded from Pro-face Home Page.

URL

http://www.pro-face.com/otasuke/

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet before

using the product.

*1 The EX module is an extension I/O unit for the LT

3000 series. To use the EX module, be sure to read

the supplied manual.

Summary of content (15 pages)

PAGE 1
This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or missing, please contact your local LT distributor immediately. LT-3200 Series Installation Guide Caution About the Manual Be sure to read the “Warning/Caution Information” on the attached sheet before using the product. For the detailed information on LT3000 series, refer to the following manual.
PAGE 2
Part Names and Functions Bottom Rear Front B C E F D A Name Description Color Indicator ON Green A Status LED Red Orange Flashing ON Flashing ON Flashing Logic execution mode (when logic is enabled) OFFLINE In operation RUN In operation STOP When power is turned on. In operation Major Error Backlight burnout During software startup Operation Mode (Drawing) B AUX Interface (EXT2) Used to connect the additional units (communication function etc.).
PAGE 3
General Specifications Power Supply Electrical Specifications Input Voltage DC24V Rated Voltage DC19.2 to 28.8V Allowable Voltage Drop 10ms (max.) Power Consumption 18W (max.) In-Rush Current 30A (max.) Voltage Endurance AC1000V 20mA for 1minute (between charging and FG terminals) Insulation Resistance DC500V 10MΩ (min.
PAGE 4
DIO Interface (Connector) • When preparing the cable to connect the wiring, check the pin numbers inscribed on the DIO Connector. Applicable connector Pin Arrangement A1 B1 A11 B11 2-1871940-1 CA6-DIOCN4-01 Pin No. A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 (Cable connection side) A11 Signal Name IN1 IN3 IN5 IN7 IN9 IN11 NC 0V OUT1 (PLS1, PWM1) OUT3 (PLS3, PWM3) OUT5 Pin No.
PAGE 5
Status Display Isolation Method External Connection External Power Supply None Photocoupler Isolation 22-pin connector (used with Output section) For Signal: DC 24V *1 In the case of IN0, IN2, IN4, and IN6, the input delay time generates a 5µs delay. For example, in the case of a 0.5ms-cycle sampling: 5µs (ON to OFF) + 0.5ms (sampling cycle) + 5µs (OFF to ON) = 0.51ms A minimum 0.51ms-restriction is imposed on the input pulse width.
PAGE 6
Output Specifications Output Terminal Rated Voltage Rated Voltage Range LT3201-A1-D24-K Output Method LT3201-A1-D24-C Maximum Load Voltage Output Voltage Drop Output Delay Time OFF to ON ON to OFF Voltage Leakage (when OFF) Clamp Voltage Type of Output Common Lines Common Design External Connection Output Protection Type Internal Fuse Surge Control Circuit Output Points Output Signal Display Status Display Element Isolation Method External Power Supply OUT0 to OUT3 OUT4 to OUT5 DC24V DC20.4V to DC28.
PAGE 7
LT3201-A1-D24-C Output Circuit (Source type) Fuse 2.5A +24V B8 + - OUT5 A11 Internal Circuit L OUT4 OUT3 OUT2 OUT1 OUT0 Internal Circuit DC 24V External Power B11 A10 B10 A9 B9 L 0V A8 Dummy Resistor*1 *1 (Example) The output delay time (ON to OFF) is 1.5µs where the output current is DC 24V, 50mA. Install an external dummy resistor to increase the amount of current when more responsiveness is required and the load is light.
PAGE 8
2. Installations 1. LT Installation (1) Create a Panel Cut following the dimensions in the table below. Installation Requirements Unit: mm [in.] • For easier maintenance, operation, and improved ventilation, be sure to install the LT at least 100 mm [3.94 in.] away from adjacent structures and other equipment. Panel 4≤3[0.12] thickness Y X Unit:mm[in.] LT 100 [3.94] 100 [3.94] 100 [3.94] 100 [3.94] 100 [3.94] LT 100 [3.94] 100 [3.
PAGE 9
Insertion Slot Recess Panel LT DIO Cable Specifications Completed View Hook the fastener on the Recess, DIO Cable Diameter AWG24 to 18 UL1015 or UL1007 Installation Fastener Conductor Type Stranded Wire*1 Hook and secure the fastener on the panel with a screw. *1 If the Conductor’s end (individual) wires are not twisted correctly, the end wires may either short against each other, or against an electrode. • Tightening the screws with too much force can damage the LT unit’s plastic case.
PAGE 10
(4) Remove the flathead screwdriver from the tool insertion hole (square-shaped hole). The wire insertion hole (roundshaped hole) will close and the wire will be secured. In the case of wire removal, remove the desired wire by inserting a flathead screwdriver into the corresponding tool insertion hole (square-shaped hole) following procedures (1) and (2). (5) Insert the wired DIO connector straight into the DIO I/F of the LT unit.
PAGE 11
2. • The power connector (plug) is CA5DCCNM-01 made by Digital Electronics Corporation or MSTB2,5/3-ST-5,08 made by Phoenix Contact. When connecting the Power Cord, use the following items when performing wiring. (Items are made by Phoenix Contact.) • Input and Output signal lines must be separated from the power control cables for operational circuits. • To improve the noise resistance, be sure to twist the ends of the power cord wires before connecting them to the Power connector (Plug).
PAGE 12
3. Grounding Cautions 4. • Be sure to create an exclusive ground for the Power Cord’s FG terminal. Use a grounding resistance of 100Ω, a wire of 2mm2 or thicker, or your country’s applicable standard. • The SG (signal ground) and FG (frame ground) terminals are connected internally in the LT unit. When connecting the SG line to another device, be sure that the design of the system/connection does not produce a shorting loop. • The grounding wire should have a cross sectional area greater than 2mm2.
PAGE 13
• To prevent malfunctions due to noise, communication cables must be wired separately from high-frequency lines and power lines such as high-voltage lines, high-current lines, and inverters. (3) Insert the USB cable into the USB Host Interface. To prevent the USB cable from coming off USB Cable • When using USB Host Interface in Hazardous Locations provided in ANSI/ISA-12.12.01, please fix the USB cable with the USB Holder.
PAGE 14
D’EXPLOSION-AVANT DE DECONNECTER L’EQUIPEMENT, COUPER LE COURANT OU S’ASSURER QUE L’EMPLACEMENT EST DESIGNE NON DANGEREUX”. (5) In the case of use in Hazardous Locations, be sure to check that the externally connected unit and each interface have been fixed with screws and locked. In Hazardous Locations, it’s impossible to insert or pull the cable from the applicable port. Be sure to check that the location is Non-Hazardous before inserting or pulling it.
PAGE 15
CE Marking • LT3201-A1-D24-K/LT3201-A1-D24-C units are CE marked, EMC compliant products. These units also conform to EN55011 Class A, EN61000-6-2 directives. Revision The revision number of the LT is shown in the label affixed to the LT. In the example shown below, an asterisk “*” is displayed in the position where “A” should be, meaning “Rev. A”. Inquiry Do you have any questions about difficulties with this product? Please access our site anytime that you need help with a solution. http://www.pro-face.