Specifications

ManualsBrandsPro-face ManualsComputer equipmentLT Series

Built-in 32-point DIO + 2-point AD/1-point DA

Built-in 32-point DIO + 2-point AD/2-point DA

+3-point Thermocouple Input

Built-in 32-point DIO + 2-point AD/2-point DA

+2-point Pt100 Input

Easily...

• Control pressure and flow

• Set positioning

• Monitor temperature, etc.

: Sink Type : Source Type

DC24V 16 Input Points

(10kpps 16-bit high speed counter x 4 points possible. *1)

(

2ch

)

(

1ch

)

(

2ch

)

(

2ch

)

(

3ch

)

(

2ch

)

(

2ch

)

(

2ch

)

*1 Each point with matching hardware output is 10kpps single phase 4 ch or dual phase 1 ch + single phase 2 ch.

*2 Pulse line output is 4 points, with 4-point total 5kpps maximum, PWM 2.5kHz for each point, combined use of high-speed counter matching output. DC24V output capacity.

(Output 0.5A x 8 points (1 common) / 0.2A x 8 points (1 common))

DC24V 16 Output Points

(5kpps pulse line output or 2.5kHz PWM x 4 points possible. *2)

Analog Input

(12-bit resolution, no insulation between channels)

Analog Output

(12-bit resolution, no insulation between channels)

Thermocouple Temperature Input (J/K)

(no insulation between channels)

Pt100 Temperature Input

(no insulation between channels)

Type H-ADFunction Type H-ADT Type H-ADP

Tool Connector

Bar Code Reader

Conversion Cable

Serial Printer

Printer

DIO I/F

Temperature Input I/F

Analog I/F

High-Speed

Counter

Transistor

Pulse Line

PWM

Push Button

etc.

KIV Cable

Input

Output

Data Transfer Cable

( COM ) GPW-CB02

( USB ) GPW-CB03

Thermocouple

( J Type / K Type Input)

Input

[ LT Type H-AD Input (2ch) Output (1ch) ]

Output

[ LT Type H-ADT/ADP Input (2ch) Output (2ch) ]

Pt100 Input

Equipped

with DC24V

32-point

input/output

Analog

input/output

Temperature

input

5.7

inch

5.7

inch

5.7

inch

5.7

inch

Sensor

Rotary Encoder

Flow Meter

Integrated Wattmeter

Heater Lamp

Valve Magnet Switch

Motor Driver

Analog Meter

Motor Driver

Thermocouple

Platinum Temperature Resistor

Load Cell

Position Change Sensor

Recording Meter

Control Valve

Heater

Inverter

ADP only

* Built-To-Order product.

Please contact your local Pro-face distributor.

LT Series System Design and Options

See our Web site for LT Series system application examples.

Displays application screens and host data.

Switches screens, inputs values, provides switch

and lamp functions, and writes data to host equipment.

Connects power and FG terminals.

Indicates the input/output status of DIN/DOUT.

Connects to a data transfer cable.

Connects external input or output equipment.

Connects I/O units, analog units, or other Flex Network

units via Flex Network communication cables.

Indicates the status of Flex Network data communication.

Connects a temperature controller, inverter or other

external device, via an RS-232C or RS-422 cable.

These switches control the DIO connector's

Output Hold. Also, they are used to set

the S-No.'s left-most hex digit.

Connects control units such as sensors, using a

screw-clamp type connector.

Connects external Input/Output units, using a

spring-clamp type connector.

Connects Pt100 or thermocouple sensors using a

screw-clamp type connector.

* ADT/ADP Type only.

Used to set the S-No.'s right-most hex digit.

RUN: Executes logic program operation

In RUN mode, RUN/STOP of logic program can be

controlled by Editor or Offline.

STOP: Stops logic program operation

Stops the logic program regardless of the software setting.

Indicates the LT unit's operation status.

Offline

Online

––

RUN

STOP

Backlight Malfunction Detected

Major Error (STOP)

Green – Lit

Green – Blinking

Green/Red – Lit

Red – Lit

*1 Indicates the logic program status. *2 Indicates the display and touch key status.

* The Flex Network S-No. (node address) occupies one node

in the Type B+DIO connector.

Operation mode*

LED

Controller mode*

RUN (Green)

ERR (Red)

Lit during normal operation.

Lit when communication

with a connected unit is blocked.

Status LED

Description

Indicates the LT unit's current status.

I/O board error

I/O board is normal

OFF

Status LED

Turns the contact OFF (open) when a major error or watchdog timer

error is generated. See page 10, External Interfaces (Alarm Output).

Graphic Display Screen

Touch Panel

Power Supply Terminal Block

I/O LED

(Type A1/A2/B+/H1/H2)

Tool Connector

DIO Connector

(Type A1/A2/B+)

Remote I/O (Flex Network)

System Connector (Type B+/B/C)

Flex Network Status LED

(Type B+/B/C)

Serial I/F (Type C)

Dip Switches (Type B+)

Analog Input/Output Connector (Type H1/2)

DIO Input/Output Connector (Type H1/2)

Temperature Input Interface (Type H1/2)

Rotary Switch (Type B+)

RUN/STOP Switch

(LED is lit in RUN mode)

Status LED

Ready LED

(Type H1/2)

Alarm Output

Product Name Model

Description

Data Transfer Cable

USB Data Transfer Cable

DIO Connector & Cover (Soldered Type)

DIO Connector (Pressure Type)

DIO Cables

Flex Network Communication Cables

Screen Protection Sheet (Hard Type)

RS-422 Connector Terminal Block Conversion Adapter

LT Series development software

Protects display surface and keeps unit clean (5 sheets/set)

Program-input unit for the Flex Network Single-axis positioning unit. Used for parameter entry,

as well as positioning check and movement. (Also includes one FN-LD10CBL.)

Connect LT Series to a PC for downloading GP-PRO/PB C-Package data

Software

Maintenance

Options

RS-422 interface cable for multiple-type (n:1) data transmission between host controllers and LT Series units.

Converts SIO to RS-422 terminal block.

GPPRO-CNT01W-P03

GLC100-DIOCN01

GLC-DIOCN02

CGP070-ID11-M

GLC000-DIOCB11-MS

GPW-CB02

GPW-CB03

I/O Connector Terminal Block for FN-XY32SKS41

Main Unit

Options

Peripheral

Unit Options

Flex Network 64-point DIO connector terminal blocks, Spring-clamp type (set of 2)GLC-DIOCN03

DIO Connectors for LT Type H

Analog I/O Connectors for LT Type H

Temperature Input Connectors for LT Type H

Attaches LT to DIO I/F (set of 2)

Attaches LT to Analog I/F (set of 5)

Attaches LT to Temperature I/F (set of 5)

Connects distributed Flex Network units (Type B+/B/C)

GLC-DIOCN04

GLC-AIOCN01

GLC-TMCN01

FN-CABLE 2010-31-MS

FN-CABLE 2050-31-MS

FN-CABLE 2200-31-MS

GP37W2-DF00

GP070-CN10-O

RS-232C Cable

Connects the Flex Network Single-axis positioning unit and the servo and stepping drivers.

GP410-IS00-O

Single-axis Teaching Loader

FN-PC10LD41

Single-axis Motor Driver Connection Cable

(1m)

FN-PC10CB01

RS-422 Cable

GP230-IS11-O

Multi-Link Cable

GP230-IS12-O

GP-PRO/PB C-Package 03

Type A1/A2/B+ DIO Connector (5 sets of connectors and covers)

Type A1/A2/B+ DIO Connector (5 sets of connectors)

Open-end Sink DIO cable, 3m (Type A1/A2/B+)

Open-end Sink/Source DIO cable, 3m (Type A1/A2/B+)

Installation Fasteners

Installation Gasket

Flex Network I/F Connectors

GP070-AT01

GP37W2-WP00-MS

FN-IFCN01

FN-LD10CBL

For attaching LT Series unit to a solid panel. (set of 4)

For attaching LT Series unit to a solid panel.

Type B+/B/C Flex Network Connectors (set of 5)

Connects Single-axis Positioning unit to Single-axis Teaching Loader.

(10m)

(50m)

(200m)

Manual: Download the necessary PDF manuals from our web site (http://www.pro-face.com), or contact your local Pro-face distributor.

Single-axis Teaching Loader Cable (5m)

Interface cables for data transmission between host controllers and LT Series.

*1 Limited by software version

Only when using

GPW-CB02

(provided by user)