Owner's Manual

ManualsBrandsPro.Fit International ManualsApple & Android integrationPro.Fit VSM G3

Table Of Contents

#2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill

Pro.Fit VSM G3, two # 8 x 1/2” screws

Right of air vent

TOOLS REQUIRED:

PARTS INCLUDED:

LOCATION:

STEP 1. Insert the dash trim removal tool behind the trim

bezel, right of the radio. (Photo # 1). Pry outward to

release a retainer clip. Work the removal tool counter-

clockwise around the bezel until all clips are released.

(Note: The door covering the cassette player, below the

climate control is part of the radio / air vent bezel and

will come out with the radio unit.)

STEP 2. Slide the radio unit out of the dash and let hang

down, resting on a support placed below it. It is very

important that you do not let the radio hang freely and

that you do not disconnect any wiring. The flat ribbon

cable that is exposed is very fragile and expensive to

replace.

STEP 3. Place the Pro.Fit VSM G3 against the dash pad,

right of the right air vent. (Photo # 2). The bottom of the

G3 will follow the contour of the dash when aligned

properly. Using the G3 as a guide, mark the location of

two (2) screw holes. Set G3 aside. Drill two (2) pilot holes

at the marked location using a 5/64” drill bit and drill.

Align the VSM G3 over the pilot holes, insert two (2) # 8

x 1/2” screws and tighten.

STEP 4. Re-assemble the dash in reverse order. This

completes the installation of your Pro.Fit VSM G3.

Removal Tool

Follow Contour

031306-03

PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit VSM G3

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling

wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.

Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal

of this Pro.Fit VSM G3

. Pro.Fit may not be held liable for any personal injury resulting from accident or improper installation.

Pro.Fit International, Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876

VIEW INSTRUCTIONS & UPDATES

ONLINE

WWW.PRO-FIT-INTL.COM

PART NUMBER: IF-71-03-G3

Clips

Page 1

Infiniti FX35/FX45

2003-2006

Summary of content (11 pages)

PAGE 1
Page 1 031306-03 Infiniti FX35/FX45 2003-2006 PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit VSM G3 All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill PARTS INCLUDED: Pro.
PAGE 2
Page 2 012406-04 Chevrolet Colorado (2004-2006) GMC Canyon (2004-2007) Isuzu i-Series Pickups (2004-2007) PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit VSM G3. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
PAGE 3
Page 3 091305--01 Chevrolet Aveo (2004-2006) PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill, protective cloth PARTS INCLUDED: Pro.
PAGE 4
Page 4 082505-01 Ford Focus (2005-2007) PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill, protective cloth PARTS INCLUDED: Pro.
PAGE 5
Page 5 111405-01 Cadillac STS, SLS (2005-2006) PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill, protective cloth PARTS INCLUDED: Pro.
PAGE 6
Page 6 091305-00 Ford Explorer (2007-2008) PART NUMBER: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Removal Tool (DM-40-22), 5/64” drill bit and drill, protective cloth PARTS INCLUDED: Pro.
PAGE 7
Page 7 Ford Edge 2007-2008 Part Number:IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Tools Needed: Dash Trim Removal Tool, 5/64” drill bit and drill Parts Included: Pro.
PAGE 8
Page 8 Ford Escape 2008 Part Number: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Tools Needed: Dash Trim Revmoval Tool (DM-40-22), 5/64” Drill Bit and Drill Parts Included: Pro.
PAGE 9
Page 9 Dodge Sprinter 2008 Part Number: IF-71-03-G3 PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit Legend. All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break. Tools Needed: Dash Trim Revmoval Tool, Star pattern screw driver, 5/16” drill, drill bit, phillips screw driver. Parts Included: Pro.
PAGE 10
PAGE 11