Owner's Manual

INSTALLATION INSTRUCTIONS
LEXUS LS430 (2001-2003) (with or w/o GPS)
(See reverse side for Lexus ES300 (2002-2003) )
PART NUMBER: LX-52-01
Pro.Fit
logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: # 2 Phillips screwdriver, hook tools, protective cloth, 10mm socket and driver,
5/64” drill bit and drill, marking pen.
PARTS INCLUDED: Pro.Fit VSM
TM
, instructions, three (3) #8 x 1/2” screws.
LOCATION: Right of Radio
WARNING: Place a clean, protective cloth over the gear shift lever
before starting this installation. Use extreme caution while working
on this vehicle. It has wood grain panels that scratch very easily!
STEP 1. Begin by removing the lower panel that holds the seat
heater switches. Carefully insert a hook tool behind the panel and
gently pull towards you, releasing two (2) Heater clips, one (1)
each on the left and right side. (See photo #1). Unplug the
electrical connector on the back and set panel aside. Locate and
remove the three (3) Phillips screws exposed by removing the
lower panel. (See photo #1). Open the panel that covers the CD
player by pushing on it. Carefully insert a hook tool in the left and
then right corner to release two (2) clips. (See photo #1). When
the clips are released, the panel will slide off. Unhook the wiring
harness on the back and set the panel aside.
STEP 2. Removal of radio. DO NOT
disconnect any wir
es to the
radio! Remove the two (2) 10mm bolts at the base of the radio,
one on the left and one on the right. (See photo # 1). Place your
hand under the radio while pulling it forward. There are two (2)
clips, one middle left and one middle right that will release as you
pull the radio out of its cavity. (See photo # 2). Set the radio gently
aside.
STEP 3. Place the VSM
TM
against the dash pad as shown in
photo # 3. The top of the VSM
TM
will touch the bottom of the air
vents (Photo # 4) or the climate control panel (Photo # 5),
depending on if the car has GPS or not. Using the
VSM
TM
as a
guide, mark the location of the three (3) screw holes. Drill three (3)
pilot holes at the marked location using a 5/64” drill bit and drill.
These holes should be no more than 1/4
” deep. Align the Pro.Fit
VSM
TM
over the pilot holes, insert three (3) # 8 x 1/2” screws and
tighten. Reassemble the dash in reverse order.
This completes the installation of your Pro.Fit VSM
TM
.
Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this
Pro.Fit VSM
TM
. Pro.Fit may not be held liable for any personal injury resulting from accident or improper installation.
Pro.Fit International, Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651-688-3588 or 800-388-0073 Fx: 651-688-9876
Web Address: www.pro-fit-intl.com
© Pro.Fit International, Eagan, MN 2003
102202-06
PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS Pro.Fit VSM
TM
.
All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling
wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
Two 10mm bolts
Three (3) Screws
2 Heater Clips
2 CD Clips
Radio Clips
VIEW INSTRUCTIONS & UPDATES
ONLINE
@
WWW.PRO-FIT-INTL.COM
1
3
2
5
4
without GPS
with GPS