INSTRUCTIONS FOR USE Pro-Ject T1 / T1 Phono SB / BT
Dear Music Lover, Congratulations and thank you for choosing Pro-Ject Audio Systems record player. Your T1 turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble free service. Please contact your dealer if you require additional assistance. Important: Your turntable was shipped partially disassembled in order to avoid damage to sensitive parts. Please check immediately to make sure that neither the packaging nor the device was damaged in transit.
GENERAL INFORMATIONS Controls, features and connections 1 PLATTER & FELT MAT 2 CHASSIS 3 MOTOR WITH PULLEY 4 SUB – PLATTER 5 DRIVE BELT 6 TONEARM COUNTERWEIGHT 7 TONEARM LIFT LEVER 8 TONEARM REST / REMOVABLE TRANSPORT LOCK 9 TONEARM TUBE 10 HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED ORTOFON CARTRIDGE 14 LID 13 LID HINGES 14 HINGE FASTENERS 15 POWER SUPPLY SOCKET Accessories 2 SINGLE ADAPTOR 4 ALLEN KEY 1,5mm 5 COUNTERWEIGHT no.
© Pro-Ject Audio Systems · Pro-Ject T1 / T1 Phono SB / BT · Revision 2019.07.
SETUP 1. Platter and drive belt installation Please remove drive belt from accessories box and install it as shown in the following ilustration. Put the felt mat on the top of the platter. 2. Cartridge installation, stylus exchange * If you purchased this turntable in a package that included the cartridge, this has already been done for you. Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge.
3. Vertical Tracking Force setting (VTF) * This setting is only neccessary when you decided to repalce your cartridge. For factory fitted cartridge, VTF was perfectly pre-set already. Before setting the Vertical Tracking Force, confirm the exact weight of your cartridge. Pushing carefully, move the counterweight onto the rear end of the counterweight support rod as shown in the illustration below. Place the stylus pressure gauge onto the platter.
T1 SPECIFIC INFORMATIONS Controls, features and connections 1 ON/OFF SWITCH 2 DOUBLE STEP PULLEY 3 OUTPUT CABLE CONNECT IT E 4 DIRECT POWER CORD _____________________________________________________________________________________________________________ Switching on and off Pressing the ON/OFF switch alternately starts or stops the motor. Changing replay speed To play 45 r.p.m., put the drive belt over the larger diameter part of the motor pulley. To revert to 33 r.p.m.
T1 Phono SB SPECIFIC INFORMATIONS Controls, features and connections 1 ON/OFF SWITCH 4 PHONO/LINE OUTPUT, EARTH CONNECTION 2 MOTOR PULLEY 5 PHONO/LINE OUTPUT SWITCH 3 SPEED SELECTOR 6 POWER SUPPLY SOCKET _____________________________________________________________________________________________________________ Switching on and off, changing replay speed Pressing the ON/OFF switch starts the motor of the turntable. Pressing the speed selector selects between 33 r.p.m. and 45 r.p.m.
T1 BT SPECIFIC INFORMATIONS Controls, features and connections 1 ON/OFF SWITCH 2 STEPPED DRIVE PULLEY 3 PHONO/LINE OUTPUT, EARTH CONNECTION 4 BLUETOOTH SWITCH _____________________________________________________________________________________________________________ Switching on and off Pressing the ON/OFF switch alternately starts or stops the motor. Changing replay speed To play 45 r.p.m., put the drive belt over the larger diameter part of the motor pulley. To revert to 33 r.p.m.
Technical specifications Pro-Ject T1 / Pro-Ject 8.6 Nominal speeds Speed variance Wow and flutter Signal to noise Effective tonearm mass Effective tonearm length Overhang Power consumption Dimensions (W x H x D) Weight Dimensions packaging (W x H x D) Weight incl. packaging 33/45 r.p.m. 33: ±0.70% 45: ±0.60% 33: ±0.25% 45: ±0.23% -65dB 8.0g 8.
Potential incorrect use and fault conditions Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included. The platter doesn't turn although the unit is switched on: The unit is not connected to the mains power supply.
© Pro-Ject Audio Systems · Pro-Ject T1 / T1 Phono SB / BT · Revision 2019.07.