Hydraulic Floor Jack Combo Operating Instructions & Parts Manual Capacity 2 Ton Model Number F-2330BMC Lifting range for Floor Jack: 5-1/4” ~ 13” Support range for Jack Stands (per pair): 10-1/2”~16-3/4” WARNING To avoid crushing and related injuries: • NEVER work on, under or around a load supported only by a hydraulic jack. • ALWAYS use a pair of appropriately rated jack stands. WARNING: Cancer and Reproductive Harm. AVERTISSEMENT: Cancer et dommages au système reproducteur.
Ton Floor Jack Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge.
ADVERTENCIA WARNING Estudie, entienda y sega todoslos materiales impresos con / para este producto antes de su uso. No exceda la capacidad nominal. Se trata de un dispositivo de elevación solamente! Inmediatamente después de levantar, soporte la carga con un par de soportes de elevación adecuadamente evaluados. Use sólo en superficie duros y nivel. Ascensor sólo en las zonas del vehículo según especificado por el fabricante del vehículo. No se harán cambios a este producto.
OPERATION Lowering Lifting (refer to Fig 1) 1. Place vehicle in park, with emergency brake on and wheels securely chocked to prevent inadvertent vehicle movement. 2. Close release valve by turning handle clockwise until firm resistance is felt Center jack saddle under lift point. 3. Verify lift point, then pump handle until saddle contacts lift point. To lift, pump handle until load reaches desired height. 4. Transfer the load immediately to appropriately rated jack stands (always use in pairs). 1.
MAINTENANCE MAINTENANCE (continued) Important: Use only a good grade hydraulic jack oil (e.g. Mobil DTE 13M or equivalent). Avoid mixing different types of fluid and Never use brake fluid, turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause failure of the jack and the potential for sudden and immediate loss of load. 2. Lay the jack on its side and drain the fluid into a suitable container. Note: Dispose of hydraulic fluid in accordance with local regulations. 3.
REPLACEMENT PARTS Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, give model number, serial number and description below. Call or write for current pricing: phone (816) 891-6390, fax (816) 891-6599 or contact Pro-Lift Customer Support, 10939 N. Pomona Ave., Kansas City, MO 64153. Model F-2330 Part No.
2 Ton (Per Pair) Jack Stands BEFORE USE Save these instructions. For your safety, read and understand the information c ontained wit hin. The owner and operator of this equipment shall have an understanding of this product and safe operating procedures before attempting to use this product. Instructions and safety information shall be conveyed in the operator’s native language before use of this product is authorized.
WARNING ADVERTENCIA Estudie, entienda y sega todos los materiales impresos con / para este producto antes de su uso. ¡ La capacidad normal es por el par! No exceda la capacidad nominal. Use como un par igaul para soportar solamente un extremo del vehículo. Use un par para cada vehículo. Ponga la carga directamente al centro de la montura. Los soportes de gato no son para soportar los dos extremos, ni un lado del vehiculo. No se haga cambios a este producto.
OPERATION To lower load 1. With suitable jack, raise vehicle clear of stands. 2. Carefully release stopper and allow ratchet to glide down to lowest position. 3. Carefully remove stands, then carefully lower vehicle with lift device. 4. Ensure that all tools, equipment and personnel are clear before lowering load. 1. Adjust height by pulling up on ratchet bar. 2. The weight of the locking handle should secure the ratchet bar in desired position. To confirm this, simply push down on the locking handle.
ONE YEAR LIMITED WARRANTY For a period of one (1) year days from date of purchase, SFA Companies, Inc. will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies, Inc. Warranty Service Department, 10939 N. Pomona Ave.
NOTE PAGE / NOTES / NOTAS 11 SFA Companies, Inc. 10939 N. Pomona Ave. Kansas City, MO 64153 Tel.
NOTE PAGE / NOTES / NOTAS 12 SFA Companies, Inc. 10939 N. Pomona Ave. Kansas City, MO 64153 Tel.