Instructions / Assembly

Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier que les quantités des pièces reçues
sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu’à ce que vous entendiez ou sentiez la roulette (2) s’enclencher. Insérer le vérin
pneumatique (3) dans la base (1).
ÉTAPE 2 Fixez la plaque du siège (4) au coussin du siège (5) avec la flèche vers l’avant de la chaise avec quatre vis courtes (8). SERREZ TOUTES LES VIS
AVEC LA CLÉ (11).
ÉTAPE 3 Fixez les bras (7L et 7R) au coussin du siège (5) et dossier (6) avec quatre vis longues (9) pour chaque bras (7). SERREZ TOUTES LES
VIS AVEC LA CLÉ (11).
ÉTAPE 4 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas. Couvrir les trous des bras (7R et 7L) avec quatre bouchons
en plastique (10) pour chaque bras (7).
ATTENTION: AVANT D’UTILISER LE FAUTEUIL, S’ASSURER D’AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
© Office Star Products avril 2017
69220C / 69226 / 69227
BIG & TALL EXECUTIVE CHAIR
OPERATING INSTRUCTIONS
1
2
69220C / 69226 / 69227
FAUTEUIL DE DIRECTION BIG & TALL
INSTRUCTIONS DE MONTAGE
ÉTAPE 1 ÉTAPE 2
ÉTAPE 4
ÉTAPE 3
PIÈCE QTÉ
1. Base ..............................1
2. Roulettes ...........................5
3. Vérin pneumatique ...................1
4. Plaque du siège ......................1
5. Coussin du siège .....................1
6. Dossier ............................1
7. Bras (7L et 7R) ......................2
8. Vis courte ...........................4
9. Vis longue ..........................8
10. Bouchons en plastique ...............8
11. Clé ...............................1
3
1
4
5
2
11
8
6
10
3
7R
9
11
5
7L
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up. To lower
seat height sit on chair and lift lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an adjustment
that will allow the user to change the tension of the tilting feature.
Turn knob (2) clockwise to increase tension and counter-clockwise
to decrease or ease the tension. To lock, return chair to the upright
position and push lever (1) in. To unlock, pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, flip arm into the updward postion (see below), lift
arm to desire height.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are securely
tightened.
3. Check that all bolts screws and knobs are tight every three months or
as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as head
covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
PROLINE II LIMITED WARRANTY
ProLine II chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization.
At it’s option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component. The customer must prepay freight on any components returned to the factory. Return freight on components
still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. The 54666 is for persons weighing 300 lbs. or less. The 39200, 39202, 39203, 81108, 81308 & 81608 are for persons weighing 400 lbs. or less.
This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
All ProLine II chairs meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax [phone], or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.