Owner`s manual

ManualsBrandsPro Mariner ManualsConsumer electronicsTrue Power 400PS Series

DC to AC Power Inverter

TruePower 400PS Series

Owner's Manual and Installation Guide

400 Watt Inverter with Automatic Crossover

For all product, installation or service questions please visit

www.promariner.com or call ProMariner directly at: 1-800-824-0524

8:30 am to 5pm (Eastern Time)

IMPORTANT SAFETY NOTICE

SAVE THESE INSTRUCTIONS

Please read all safety, operating and installation instructions before installing

or applying AC power to your ProMariner / On Board Solutions power inverter.

Models Part No. Description

TruePower400PS 79400 GFCI Protected Outlets

TruePower400PS 79405 Hardwired

090308

specifications subject to change without notice

On Board

Solutions

A ProMariner Company

On Board

Solutions

A ProMariner Company

Factory Service

TEL: 1-800-824-0524

www.promariner.com

8:30 - 5:00 Eastern Time

200 International Drive, STE 195

Portsmouth, NH 03801

ProMariner

™

ProMite Series - Recreational Grade Waterproof Marine Battery Chargers

ProTournament Series - Professional Grade Waterproof Marine

Battery Chargers

ProNautic C

Series All Digital Dry Mount Battery Chargers

ProTech-i Series Dry Mount Battery Chargers

Digital Mobile Charge In-Transit Chargers

Battery Maintainers

AC Plug Holders

Battery Isolators

Isolation Transformers

Galvanic Isolators and Monitored Systems

Corrosion Control Products

Waterproof Marine Binoculars

A Complete Line of Hand Held Test Meters

Online Technical Support and Service Support

Visit ProMariner Online at www.promariner.com, for a Complete

Selection of Quality Marine Products...

Here are just a few:

Visit frequently, we are always adding new products for your

boating enjoyment!

ProMariner

™

Summary of content (11 pages)

PAGE 1
On Board ProMa r i ne r Solutions ™ A ProMariner Company Visit ProMariner Online at www.promariner.com, for a Complete Selection of Quality Marine Products...
PAGE 2
TABLE OF CONTENTS Safety Instructions... TruePower400PS Overview... TruePower400PS Features... Installation Guidelines... Operation... Troubleshooting... Specifications... Customer Service and Warranty... Page 1 - 2 Page 2 Page 3 - 4 Page 5 - 10 Page 11 - 12 Page 13 Page 14 Page 15 INTRODUCTION Thank you from all of us at Professional Mariner and Onboard Solutions.
PAGE 3
Safety Instructions 1 GENERAL SAFETY INSTRUCTIONS Before installing and using your new inverter, read all appropriate sections of this guide and any cautionary markings on the inverter, batteries and on your appliances. 1) SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for inverter models 79400 and 79405.
PAGE 4
TruePower400PS Overview 2 PERSONAL SAFETY PRECAUTIONS CONTINUED Never smoke or allow a spark or a flame in the vicinity of a battery or engine. Be extra cautious to reduce the risk of dropping a metal tool onto a battery. It may spark or short-circuit the battery or other electrical parts that may cause an explosion. Remove all personal metal items such as rings, bracelets, necklaces, watches and jewelry when working near a battery.
PAGE 5
TruePower400PS Features Customer Service & Warranty 3 16 INVERTER FEATURES CUSTOMER SERVICE & WARRANTY Product Features We are committed to customer satisfaction and value your business. If at any time during the warranty period you experience a problem with your new TruePower400PS inverter simply call us at 1-800-824-0524 during standard business hours (8:30 AM – 5 PM Eastern Standard Time) for technical support.
PAGE 6
Specifications TruePower400PS Features 4 15 ELECTRICAL SPECIFICATIONS Battery Low Shutdown: Continue Output Power: Input Voltage Range: Input Full Load Current: No Load Power Draw Output Frequency: Output Power: Output Voltage (At No Load): Output Voltage (At Full Load): Peak Output Power: 10.5 VDC 400 W 10.5 – 15.3 VDC 40 A 0.5 A 60 +/- 0.
PAGE 7
Tr o u b l e s h o o t i n g Installation Guidelines 5 14 PREPARING FOR INSTALLATION Problem: No output voltage. Inverter light is illuminated. Cause: Inverter may be overloaded. Battery voltage may be too high. Over temperature. Solution: -Disconnect all appliances connected to the inverter & reset the inverter by turning the ON/Off switch to Off then back to ON. -The inverter will restart if the battery voltage drops below 15.5 volts DC. -Allow the inverter to cool down.
PAGE 8
Installation Guidelines Tr o u b l e s h o o t i n g 13 6 TROUBLE SHOOTING GUIDE MOUNTING YOUR INVERTER This section is designed to accommodate you in identifying and troubleshooting common problems that may result with a Sine Wave inverter. Review this section before contacting customer service. If you can not resolve the problem, record the data of the instance based on information provided here with in this manual. To mount the TruePower400PS Inverter: 1.
PAGE 9
Installation Guidelines General Operation 12 7 INSTALLATION CONTINUED OPERATION CONTINUED To Connect the Chassis Ground: Refer to figure 3 Resetting the Inverter: To reset the TruePower400PS, turn the ON/Off switch to Off and then back to ON. Figure 3 DC Input Remote Resetting the Supplemental Circuit Protection Button: If there is a short circuit or an overload condition, the supplemental circuit protection button trips.
PAGE 10
General Operation Installation Guidelines 11 8 OPERATION INSTALLATION CONTINUED The ON/Off switch turns the TruePower400 PS to ON or to Off. - In the ON position, the Inverter / Fault LED light will illuminate Green. The TruePower400PS begins inverting and provides 400 watts of sine wave power, if shorepower is not present. - In the Off position with no shorepower present, the TruePower400PS draws no current from the battery.
PAGE 11
Installation Guidelines Installation Guidelines 9 10 INSTALLATION CONTINUED INSTALLATION CONTINUED 7. Strip approximately 3/8 inch off the insulation of the cable. 8. Run the AC cable through the clamp and into the wiring box. 9. Using a screwdriver, loosen the wire attachment screws on the terminals by about five turns. 10. Insert and fasten the Ground wire into the corresponding terminal. 11. Insert and fasten the Line and Neutral wires into the corresponding terminals. 12.