[Profile] The Station Profile page shows the settings and current operation status of the station. [Link Status] The Station Link Status page shows the settings and current operation status of the Station.
[Site Survey] Station Site Survey page can shows information of APs nearby, you can choose one of these APs connecting or adding it to profile. For adding a profile, choose one AP and click “Add Profile”. And you will see the below screen for AP profile configuration. Enter the necessary information and apply the settings.
[Statistics] The Station Statistics page shows the settings and current operation status of the Station. [Advance] The Station Advanced Configuration page shows the settings and current operation status of the station.
Wireless Mode: Select wireless mode. 802.11B/G mix, 802.11B only, 802.11G only, 802.11N only, 802.11 GN mix mode ,and 802.11B/G/N mix modes are supported. Country Region Code: The available channel differs from different countries. For example: USA (FCC) is channel 1-11, Europe (ETSI) is channel 1-13. The operating frequency channel will be restricted to the country user located before importing. If you are in different country, you have to adjust the channel setting to comply the regulation of the country.
B/G Protection: User can choose from Auto, On, and Off Î Auto: STA will dynamically change as AP announcement Î ON: Always send frame with protection. Î Off: Always send frame without protection. TX Rate: Manually force the Transmit using selected rate. Default is auto. Tx Burst: Frame burst mode. HT Physical Mode: Configure HT Status in use, containing HT(MM or GF), BW(20 or Auto), GI(Long or Auto), and MCS(0~15, 32, or Auto) settings.
connects if the value is zero. (3) DLS Status After configuring DLS successfully, show MAC address of the opposite side and Timeout Value of setting in “DLS Status”. In “DLS Status” of the opposite side, it shows MAC address of itself and Timeout Value of setting. [11n Configurations] The Station 11n Configurations page shows the settings and current operation status of the station. MPDU Aggregation: MPDU stands for MAC Protocol Data Unit.
[WPS] You can setup security easily by choosing PIN or PBC method to do Wi-Fi Protected setup. WPS AP Site Survey: Display the information of surrounding APs with WPS IE from last scan result. List information includes SSID, BSSID, RSSI, Channel, ID (Device Password ID), Auth., Encrypt, Ver., and Status. Refresh: Issue a rescan command to wireless NIC to update information on surrounding wireless network. Mode: Our station role-playing as an Enrollee or an external Registrar. PIN : 8-digit numbers.
3.3 Quick Start Quick Start will help you setup Wireless 11n Router quickly. There have five types of WAN Connections: Static (Fixed IP), DHCP (Auto Config), PPPoE (ADSL), PPTP, L2TP, and BigPond. 3.4 Internet Settings The Internet Settings contains the following sections: WAN LAN DHCP Clients VPN Passthrough DNS Advanced Routing QoS 3.4.1 WAN The WAN port is the connection of the 802.11n AP Router module to existing broadband device such as Cable modem or ADSL CPE.
This AP Router supports 5 methods of obtaining the WAN IP Address: -- Static IP (fixed IP): Use static IP address to access Network. Your ISP will provide a static IP address. -- DHCP (Auto Config): Automatic gets IP address from your ISP. -- PPPoE (ADSL): PPPoE is an common connection type used for xDSL. -- PPTP: PPP Tunneling Protocol can support multi-protocol Virtual Private Network (VPN).
LAN IP Address: The LAN IP address. Default: 192.168.1.1 Subnet Mask: The LAN net-mask. Default: 255.255.255.0 DHCP Type: Select Disable to disable this Router to distribute IP address. Select Server to enable this Router to distribute IP addresses (DHCP server). And the following field will be activated for you to enter this starting IP address. Start IP address: Specify the starting IP address of the IP address pool. Default Start IP: 192.168.1.100.
