Instruction manual & spare parts list AG-PRO 7 AG-PRO 5 AG-PRO 4 AG-PRO SERIES AIR DRIVEN ANGLE GRINDERS Revision date 05/2008
1.General Safety and Operation Instruction 1. Unpacking When unpacking this product, carefully inspect for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting this product into service. 2. This product is a part of a high-pressure system and the following safety precautions must be followed at all times along with any other existing safety rules. 3. Read all manuals included with this product carefully.
16. Keep all nuts, bolts and screws tight and ensure equipment is in safe working condition. 17. Do not put hands near or under moving parts. 18. Speed Adjustment The grinder should never be used to set torque. Use a torque wrench to set the torque. Are equipped with regulators for speed adjustment. To remove nuts, set the regulator to the maximum setting. To install nuts, set the regulator to the minimum to medium setting. Do not over tighten the nuts. 19.
2. Information of Vibration Level (1)The vibration level at the handle is about： 1.792 ~ 5.706 2 m/s . (2)Reference standard：EN 28662-1. 3. Information of Temperatures (1)The temperatures at the handle (8 hours/Operation) is 30 ℃. 4.Safety Information Rated rotational speed of the spindle is 5000 ~ 70000 R.P.M. 5. Safety Information a. General (1) The Grinder shall be stored in a safe way.
6. Explanations Of Warning Signs used For This Tool The operator’s Instruction must be read before work starts Direction of rotation Reverse function Hearing protection must be worn Eye protection must be used or safety glasses worn Engine oil Fuel 7. Application Power tool driving a rotating spindle on which a bonded abrasive product is mounted. 8. The weight of this tools is about： 0.44 ~ 2.7 Kgs.
Disconnect the grinder from the air supply before lubricating. 1. Disconnect the die grinder from the air supply. 2. Turn the die grinder upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of oil in the air inlet. Then, push the forward and reverse button in both directions. After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation.
General Trouble shooting Guide Symptom Possible Cause(s) Tool runs slowly or 1. Grit or gum in tool. will not operate Corrective Action 1.Flush the tool with air tool oil, gum solvent, or an equal mixture of SAE # 10 motor 011 and kerosene. Lubricate the tool after cleaning. 2 No oil in tool. 2.Lubricate the tool according to the lubrication instructions in this manual. 3 Low air pressure 3.Adjust the compressor regulator to tool 4 Air hose leaks 4.
UNITOR AG-PRO 4 B SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 4” ＊AIR PRESSURE --------------- 90 PSI ＊AIR INLET -------------- 1/4” PT(NPT) REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 PARTS NO.
UNITOR AG-PRO 4 B Revision date 05/2008
UNITOR AG-PRO 5 SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 5” ＊AIR PRESSURE --------------- 90 PSI ＊AIR INLET -------------- 1/4” PT(NPT) REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 48 49 50 51 PARTS NO.
UNITOR AG-PRO 5 Revision date 05/2008
UNITOR AG-PRO 7 SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 7” ＊FREE SPEED ----------------- 7,600 RPM ＊AIR PRESSURE --------------- 90 PSI ＊HOSE SIZE -------------------------- 1/2” ID ＊AIR INLET -------------- 3/8” PT(NPT) REF PART NO. DESCRIPTION Q‘TY REF PART NO.
UNITOR AG-PRO 7 Revision date 05/2008
Fraser/surrey Gaspe Gros Caouna Halifax Hamilton Harbour Grace Holyrood Kitimat Long Pond Marytown Montreal Nanaimo New Westminster Bc Pictou/halifax Pointe Aux Pic.quebec Port Alfred Port Cartier Port Colborne Port Hawkesbury Port Mellon Port Moody Port Of Quebec Port Weller Powell River Prince Rupert Roberts Bank Saint John Sarnia, Ontario Sept Iles Seven Islands Sorel Souris/ halifax Squamish St. Catherines St.john’s, Nfld St.
