Instructions / Assembly

ManualsBrandsPRO-SERIES ManualsBuilding materials12 ft. 2-Story Rolling Scaffold Tower with 1000 lb. Load Capacity

ITEM # TOWERINT

Scaffold

Assembly & Operating Instructions

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

This manual provides important information on proper operation and maintenance. Every effort has been

made to ensure the accuracy of this manual. We reserve the right to change this product at any time

without prior notice.

Questions? Problems? CONTACT BUFFALO CORP

If you experience a problem or need parts for this product, visit our website http://www.buffalotools.com or

call our customer help line at 1-636-532-9888, Monday-Friday, 8 AM - 4 PM Central Time. A copy of the

sales receipt is required.

NOTE: This scaffold can be used indoors, and can be used outdoors on flat surfaces. It should not be stored

outdoors, as the wood platform is not water resistant. This item is not compatible with stem jacks.

Summary of content (8 pages)

PAGE 1
ITEM # TOWERINT Scaffold Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation and maintenance. Every effort has been made to ensure the accuracy of this manual. We reserve the right to change this product at any time without prior notice. Q uestions? Problem s? CO N TACT BU FFALO CO RP If you experience a problem or need parts for this product, visit our website http://www.buffalotools.
PAGE 2
ITEM# TOWERINT Assembly and Operating Instructions WARNING: Improper erection, dismantling or use of Multi-Use Scaffold may result in serious injury or death! Erectors, dismantlers, and users of Multi-Use Scaffold must read and fully understand these Safety Rules and Instructions.
PAGE 3
STEP 1 Attach side brace B to two frames A: • Pull L-shape lock pin at each end of side brace to the disengaged position. (See Figure B) • While holding L-shape pin in disengaged position, place U-channel on each end of side brace B around leg of frame A at desired platform height. • Release lock pin and be sure that pin fully engages into hole in frame A leg • Install Connector Pins F under Lock Pin on all four sides.
PAGE 4
WARNING: • RECHECK ALL SIDE BRACE LOCK PINS FOR FULL ENGAGEMENT BEFORE ACCESSING PLATFORM. • RECHECK PLATFORM TO BE SURE IT IS PROPERLY SEATED WITHIN SIDE BRACE CHANNEL AND THE PLATFORM CLIPS ARE FULLY ENGAGED BEFORE ACCESSING. • WHEN ACCESSING PLATFORM, CLIMB OVER TOP OF FRAME LADDER – DO NOT SWING AROUND SIDE OF FRAME. • REMOVE THE PLATFORM BEFORE ADJUSTING THE DECK LEVEL.
PAGE 5
SCAFFOLDING SAFETY RULES SERIOUS INJURY OR DEATH MAY RESULT FROM IMPROPER ERECTION OR USE of scaffolding equipment. Erectors and users must be familiar with and follow safe practice and the Safety Rules contained herein. These Safety Rules cover generalized situations only and should not be used to replace any other additional safety and precautionary measures that may be necessary to cover the many usual or unusual conditions encountered during installation or dismantling.
PAGE 6
K. TIEING THE SCAFFOLD TO THE STRUCTURE IS OF GREAT IMPORTANCE to the stability and safety of the scaffold. Assure that the structure to which the scaffold is tied or anchored is capable of safely supporting all loads imposed by the scaffold. L. FREE STANDING SCAFFOLDS other than wall scaffolds must be restrained from tipping by guying or other means, recognizing that stability is essential to the safety of the scaffold. M.
PAGE 7
ASSEMBLE TWO SCAFFOLD UNITS TO BUILD ONE SCAFFOLD TOWER (A) 1-Piece Guard Rail System Set (Item No. GSGRSU) For interior or exterior use. Includes hinged doors, steel frame, durable powder coat paint finish. Assembled size: 69 inch L x 39 inch H x 29 inch W (B) 2-Pieces 6 Foot Multi-Use Scaffold Unit (Item No. GSSI) (C) 4-Pieces 18 inch Outrigger (Item No. GSORSET) For interior or exterior use. Steel frame, powder coat paint finish. Extends the width of the base so that units can be stacked.
PAGE 8
Assembling ITEM# GSORIG Outriggers to Scaffolding * Attach the clamp to the bolt, and securely tighten it. Repeat on all four support legs. GSSI The outriggers and steel bolts are placed OUTSIDE the leg of the GSSI. Tighten This Clamp X GSORIG DO NOT insert the steel bolts into the holes of the GSSI support leg. ✔ Inside View Tighten This Clamp Wheel from Stacked GSSI WARNING Wheel from GSSI GSSI Be certain that all Outriggers are securely tightened.