Owners Manual • Bedienungsanleitung Manuel de l'utilisateur • Manuale dell'utente PRB4100B 29
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product. WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
EN Introduction Pro Boat® RC models look as good as they perform. Our boats, which include everything from scale sailboats to fully licensed powerboats, exceed expectations and provide years of radio control fun and excitement. Whether your passion leads you towards the pure serenity of sailing or the all-out speed of a Deep-V, Pro Boat models fit your taste, budget and lifestyle.
EN Battery Chemistry Switch This switch allows the ESC to detect voltage. When the switch is in the OFF position, low voltage cutoff (LVC) is disabled. You will know you have reached LVC when the motor power decreases while the boat is in operation. Li-Po: move the battery chemistry switch to the ON position Ni-MH: move the battery chemistry switch to the OFF position. Tip: The ESC programming card (DYNM3821, sold separately) allows the consumer to adjust low voltage cutoff and other ESC programming.
EN Transmitter Battery Installation 1 2 This transmitter requires 4 AA batteries. 3 1. Remove the battery cover from the transmitter. 2. Align the battery polarity with the markings in the compartment and install the batteries. 3. Install the battery cover. Transmitter Controls Reverse Switch BIND ST N TH R N R Allows you to change the direction of steering (ST. REV) and throttle (TH. REV) controls. Ensure proper function with a radio system test.
EN Getting Started 1. Power on the transmitter. 4. Power on the ESC switch. 2. Turn ON the Li-Po battery switch (when using Li-Po batteries). 5. Do a test of the transmitter’s control of the boat with the boat on the display stand. 6. After launching the boat in the water, start driving slowly, and, if the boat does not go straight, adjust the steering trim dial on the transmitter. 3. Connect the battery. ST. TRIM 1 2 R POWE TH. TRIM 4 3 ST. RATE ST. TRIM POWER 5 ST. RATE TH. TRIM 6 ST.
EN Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The DX2E and MR200 are bound at the factory. If you need to rebind, follow the instructions below. 1. With the receiver off, insert the bind plug into the BND/BAT port on the receiver. 2. When a battery is connected to the ESC and the ESC is connected to the throttle port on the receiver, power on the ESC switch.
EN Center of Gravity Moving the batteries to the front or back of the compartment can significantly affect the boat's performance. 2. Move the batteries toward the front of the boat for faster initial acceleration to eliminate oscillation or bouncing, and to increase stability. 1. Move the batteries toward the rear of the boat to raise the front of the hull for increased speed.
EN B Maintenance Always replace the flex shaft when it is damaged or shows visible wear or injury and property damage may result. Lubricating the flex shaft is vital to the life of the drivetrain. The lubricant also acts as a water seal, keeping water from entering the hull through the stuffing box. A 4. Carefully reinstall the flex shaft in the drive strut, stuffing box and collet.
EN ESC The included ESC programming card (DYNM3821) allows you to quickly program your Dynamite® Marine Brushless ESC control settings. Brake: ON or OFF ON: The boat will stop immediately when the throttle is returned to neutral. OFF: The boat will coast to a stop. Programmable Settings Timing: Low Timing or High Timing Throttle Reverse: ON or OFF Cutoff Voltage: High Cutoff or Low Cutoff High Cutoff: The Ni-MH Cutoff voltage is .9 volts per cell and the Li-Po Cutoff is 3.3 volts per cell.
EN Checklists Before Boating After Boating • Install fully charged batteries in your boat and transmitter • • Connect the boat’s battery to the ESC Always power off the receiver before powering off the transmitter to maintain control of the boat and to retain transmitter binding • Make sure the boat is bound to the transmitter (otherwise, bind the boat to the transmitter using the included binding instructions) • Disconnect the battery from the receiver and remove the batteries from the boat •
EN Troubleshooting Guide Boat will not connect (after binding) to transmitter Boat tends to dive in the water or takes on water Transmitter is too near boat during connecting process Move powered transmitter a few feet from boat, disconnect and reconnect battery to boat Boat or transmitter is too close to large metal object, wireless source or another transmitter Move boat or transmitter away from large metal object Bind plug is left installed Rebind transmitter to boat and remove bind plug before c
EN Limited Warranty What this Warranty Covers Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
EN Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-ofpurchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
EN FCC Information Antenna Separation Distance This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
EN Identification of Components / Identifizierung der Komponenten Identification des composants / Identificazione dei componenti R A S B Q C P E G D F H O I N M L K 16 J Miss Geico 29
EN Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio A PRB3835 1500Kv BL Motor B PRB3307 Motor Mount C PRB4107 Flex shaft D PRB4109 Prop Nut E PRB4113 Flex shaft Liner F PRB0151 Propeller, plastic PRB4111 Rudder Pushrod Set: MG29 G PRB4012 Antenna Tube H DYN3900 Digital Servo I PRB4106 Rudder J PRB4105 Strut and Mounts K PRB2239 Drain Plug L PRB2068 Water Outlet and Nut M PRB4101 Hull: MG29 N PRB4103 Inner Seal O PRB4102 Canopy: MG29 P
32596 Printed: 7/2012 ©2012 Horizon Hobby, Inc. Pro Boat, DSM, DSM2, Dynamite, Speedpack, Prophet, EC3, the Pro Boat logo and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks or logos are property of their respective owners.