AIR FILTRATION DEVICE Operating instructions (ENG) MODEL: 10079020 Read these instructions before using the machine.
Machine Data Label Overview The Triad AFD (Air Filtration Device) improves healthful air quality, removing particulates including mold and spores.
Table of Contents Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Safety Label Location . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 5 Installing AFD on the Triad Thruster Fan . . . . . . . . . 6 Back Draft Prevention . . . . . . . . . . . .
Safety Safety Label Location Label, Warning AFD 8.633-799.
Operation Technical Specifications ITEM Weight Length Width Height Construction Duct Inlet Connection Filters Triad Air Flow Rate SPECIFICATION 25.0 lbs. 25.25” 20.25” 12” Durable Rotomold Body 12” Diameter Flex Duct 1st Stage - 1” Pleated 2nd Stage - 1” Pleated 2nd Optional Stage - 1” Activated Carbon 3rd Stage - 2” HEPA 450 CFM with filters at 1.
Operation Installing AFD on the Triad Thruster Fan Back Draft Prevention 1. Remove all cords and ducting from fan's top intake nozzle. 2. Check all seals and gaskets for any damage. If required, only replace with Prochem factory parts. 3. Lift the AFD over the Triad fan. 4. Catch the fan's top intake flange with the AFD's 2 housing retention tabs, and let it rest on top of the fan. 5. Tighten the AFD's securing knob until the knob's ball is tightly under the fan's intake flange.
Maintenance Filter Replacement 1. Remove any cords wrapped around neck of AFD The filters will have captured potentially dangerous mold spores that may have been in the air in the disaster restoration and remediation environment. Follow all standards and recommendations found in IICRC S500 and IICRC S520. 2. Unlatch and remove the upper housing. 3. Flip the upper housing over. 4. Rotate the 4 filter retention tabs to clear the filters. 5. Remove the stage 2 filter, then the stage 1 filter. 6.
Maintenance Cleaning Perform after each job. 1. Dispose of all filters properly as per IICRC S520. 2. Disassemble the AFD and clean thoroughly as per IICRC S520. NOTE: The rotomold halves of the AFD can be sprayed with water since the AFD contains no electronics or other components that can not be wet. 3. Towel dry parts or allow parts to air dry. 4. Install new filters. 5. Re-assemble AFD. 6. Place clean AFD into a bag and close bag until next use.
Parts PARTS 86337980 Air Filter Device 9
Lower Housing 22 21 7 14 12 1 15 18 11 23 17 5 15 20 16 2 15 13 17 15 3 10 6 16 9 16 20 10 86337980 Air Filter Device 20 4 19 8
Lower Housing REF PART NO. PRV NO. QTY DESCRIPTION SPACER, NYLON .219ID X .5OD X .156H KNOB, BALL HANDLE BASE, HANDLE KNOB, 1.38OD X 3/8-16 X 2.
Upper Housing 4 1 3 2 12 10 8 7 9 5 11 13 14 9 6 15A 15B 12 86337980 Air Filter Device
Upper Housing REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 86338750 86338080 86338040 86338000 86336520 86336240 86278990 86276290 86275460 86272620 86173340 86010630 86276160 87017 70626 70481 80670 87514 87013 70604 1 1 1 1 4 1 1 1 2 1 4 2 4 ASM, RESTRICTOR PLATE LANYARD, 6.0 W/LOOP & EYE RING, SPLIT, ID .
Suggested Spare Parts 14 PART NO. PRV NO. DESCRIPTION 98409300 - SET, 10 HEPA FILTER 98409540 - SET, 12 STAGE 1 FILTER 98409550 - SET, 12 STAGE 2 FILTER 86161800 86338000 86338750 86336580 86336590 86338070 86338060 86336520 86341690 46-802531 - LATCH, CONCEALED KEEPER PLUG, CONTAINMENT ASM, RESTRICTOR PLATE SEAL, UPPER SEAL, LOWER HANDLE BASE, HANDLE TAB, FILTER RETENTION FILTER, CARBON ACTIVE, 16 X 16 X 1 86337980 Air Filter Device SERIAL NO.
Serial Numbers REF. NO.
