LGR DEHUMIDIFIER Operating instructions (ENG) MODEL: 10079000 Read these instructions before using the machine.
Machine Data Label Overview The Trident LGR Dehumidifier is intended for professional disaster restoration and remediation, but can also be used for construction, janitorial / sanitation or other professionals needing to control humidity in an area. Warranty Registration Thank you for purchasing a Prochem product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to : www.prochem.
Table of Contents Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How To Use This Manual . . . . . . . . . . . . . . . . . . . . . 4 Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5 CONSIGNES IMPORTANTES DE SÉCURITÉ . . . . 6 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 7 DEGRÉS DE RISQUES EN CAS DE DANGER. .
How To Use This Manual This manual contains the following sections: • • • • • How to Use This Manual Safety Operations Maintenance Parts List The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
Safety IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain or water. Use only as described in this manual. Use only manufacturer's recommended components and attachments. Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
Safety CONSIGNES IMPORTANTES DE SÉCURITÉ Lors de l'utilisation d'un appareil électrique, il faut toujours observer des précautions élémentaires, qui comprennent parmi celles-ci: LISEZ BIEN L'ENSEMBLE DES CONSIGNES AVANT D'UTILISER CET APPAREIL. Utilisez-le exclusivement dans des endroits fermés. Ne l'utilisez pas en plein air et ne le laissez pas sous la pluie. Utilisez-le exclusivement de la manière décrite dans ce manuel.
Safety The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
Safety Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions: DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante: ! AVERTISSEMENT: AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort.
Safety 115V Grounding Instructions ELECTRICAL: Grounding Pin In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the machine.
Safety Safety Label Location NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement. Emplacement De L'étiquette De Sécurité REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment, les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapide. Warning Label 8.633-839.
Operations Technical Specifications ITEM MEASURE Height 35 In (89 cm) Length 23 In (58 cm) Width 20.5 In (52 cm) Cord 25’ X 14 Gauge / 3 Wire Black Body Construction Rotationally Molded Polyethylene Frame Construction Powder Coated Steel Refrigerant R410A / 630 grams Water extraction / Day 110 pints @ 80°F/60% RH Max Process Air rate 350CFM / 10 CMH Electrical Fan 2.4 Amps @ 110 / 120 VAC 60 Hz Compressor 6.0 Amps @ 110 / 120 VAC 60 Hz Total Power 8.
Operations 3 2 1 4 9 10 5 6 7 8 Components 1. Power Cord 2. Handle 3. Intake Nozzle/Cord Storage 4. Filter 5. Housing Lid 6. Ducting Flanges 7. Exhaust Nozzle 8. Wheels 9. Power Switch 10.
Operations How to Transport Dehumidifier 1. Wrap the power cord around intake nozzle. 2. Tilt on back wheels with exhaust outlet pointing up. 3. Pull by handle. 4. Place the machine back down on its base. 5. Position exhaust as desired. Storing in Warehouse and in Delivery Truck: Dehumidifiers should always be stored and transported in an upright position. If the dehumidifier is transported in a horizontal position, upon being set upright the unit should not be operated for 30 minutes.
Operations Operating Dehumidifier Ducting Never allow anything to block intake airflow. Be careful of objects which could be drawn against intake. The fan must sit on a level surface. Always position and orient machine before turning on. Switch off and unplug machine from its power source before connecting ducting. ! AVERTISSEMENT: Arrêtez et débranchez le ventilateur de sa source d'énergie avant de relier la canalisation. ! ATTENTION: Ne permettez jamais à quoi que ce soit de bloquer l'entrée d'air.
Operations Exhaust Ducting Intake Ducting 1. Place quick-ducting band over lay-flat duct approximately 1 foot from end. 1. Unwrap cord from cord storage area. 2. Slide ducting 3 or 4 inches over front exhaust nozzle, make sure it is even all around. 3. Secure in place by sliding quick-ducting band along ducting and over exhaust ducting flange. 4. Verify that ducting is sandwiched between machine exhaust nozzle and quick-ducting band and even all around making a good seal. 5.
Operations Back Draft Prevention Purging Dehumidifier Exhausting too much air from a space with Open Combustion Devices (e.g. furnace, fireplace or water heater) can cause those devices to back draft. This can contaminate the space with potentially fatal gases. Évacuer trop d'air d'un espace avec des appareils à combustion ouverte (p ex., fournaise, foyer ou chauffe-eau) peut entraîner un refoulement de ces appareils. Cela peut contaminer l'espace avec des gaz potentiellement mortels. 1.
Maintenance Service Schedule Power Cord Filter Coils Heat Exchange Block Condensate Pump Condensate Drip Tray Daily Daily Monthly Monthly Monthly Monthly Inspect for wear, fraying or cuts. Inspect, vacuum up to 3 times, replace as needed Inspect, clean when visibly dirty Inspect, clean with compressed air only when needed. Inspect, clean when needed. Inspect, clean when needed. Cleaning Dehumidifier Do not perform any cleaning operations with the unit plugged into power.
Maintenance Fan Replacement Thermistor Replacement The motorized impeller has internal thermal overload protection. If defective, the complete assembly must be replaced. The defrost thermistor is attached to the refrigerant suction line between the accumulator and the evaporator. 1. Unplug power cord. 1. Unplug unit from power. 2. Remove condensate cover to disconnect the impeller fan leads. 2. Remove drain tube from machine. 3. Open housing lid, remove air filter. 3.
Maintenance Troubleshooting PROBLEM Nothing runs Coils don’t get hot and cold Compressor doesn’t run Fan doesn’t run Machine doesn’t extract as much water as expected Water drips from machine CAUSE Defective switch Defective control board Loose connection in internal wiring Compressor is not running. Leak in system / refrigerant gone. Bad connection in compressor circuit. Defective compressor capacitor. Defective compressor overload. Defective compressor. Defective control board. Defective relay.
Notes: 20 86352290 Trident LGR Dehumidifier
Parts PARTS 86352290 Trident LGR Dehumidifier 21
Air Mover 4 2 5 3 10 7 1 6 9 8 22 86352290 Trident LGR Dehumidifier
Air Mover REF 1 2 3 4 5 6 7 8 9 10 PART NO. QTY 86349360 86341580 86337710 86337700 86264920 86173320 86173310 86172870 86134850 86013850 8 5 1 1 1 4 4 4 4 8 DESCRIPTION SERIAL NO. FROM NOTES SCR, PHMS M6 X 25 SS SPACER, DEHU IMPELLER PLATE, AIR MOVER MOUNT FAN ASM, DEHU 250MM CABLE TIE, .
Compressor 3 5 1 6 2 7 4 24 86352290 Trident LGR Dehumidifier
Compressor REF PART NO. QTY 1 2 3 4 5 6 7 86350050 86172650 86337650 86337630 86337530 86337510 86013850 1 3 1 1 1 1 3 DESCRIPTION SERIAL NO.
Electronics 25 18 1 16 24 23 3 8 22 21 2 9 13 15 11 12 5 10 17 19 4 14 22 6 7 26 21 26 20 22 86352290 Trident LGR Dehumidifier
Electronics REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PART NO.
Frame & Wheels 3 4 17 17 1 15 15 6 12 14 16 9 7 8 10 5 16 2 11 13 28 86352290 Trident LGR Dehumidifier
Frame & Wheels REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86341010 86001660 86337600 86337540 86337480 86337470 86337450 86331810 86331700 86331680 86309790 86273700 86219480 86173300 86172870 86172640 86172630 2 2 1 1 2 2 1 3 1 3 2 4 2 2 6 4 6 DESCRIPTION SERIAL NO. FROM NOTES BRKT, ATTACHMENT HUBCAP, 5/8 SHAFT BRKT, REAR ATAXH SUPPORT FRAME ASSY, DEHU BUSHING, 5/8" AXLE BRKT, AXLE MOUNT AXLE, DEHU WASHER, M5 SPLIT LOCK SS SCR, M5 X 25 PPHMS SS NUT, M5 HEX SS WHEEL, 12" X 2.
Housing 12 8 4 10 7 11 2 5 1 13 11 13 2 5 11 9 30 6 1 2 2 86352290 Trident LGR Dehumidifier 3
Housing REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 86349360 86013850 86341780 86341770 86340860 86350540 86337440 86333040 86302700 86276290 86173310 86337770 86353670 4 16 2 1 4 1 1 1 3 4 14 1 2 DESCRIPTION SERIAL NO.
Housing-Upper 16 5 10 4 8 12 6 1 12 8 15 9 2 14 9 2 11 7 13 11 3 32 86352290 Trident LGR Dehumidifier
Housing-Upper REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 86349400 86349360 86349230 86337460 86337430 86337420 86173330 86173320 86173310 86172950 86172820 86172630 86024750 86013850 86349220 86351480 8 5 1 1 1 2 2 8 5 2 4 8 2 3 1 1 DESCRIPTION SCR, M4 X 20 FHMS SS SCR, M4 X 25 PHMS SS FAIRING W/ SEALS FILTER, 14 X 14 X 1 MIRV CATCH LEVER HINGE, 2 X 1.
Condensate Pump 4 3 8 2 10 1 7 10 10 8 8 7 7 6 9 5 11 34 86352290 Trident LGR Dehumidifier
Condensate Pump REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 86351420 86341910 86341900 86341710 86337720 86350040 86302700 86173310 86172640 86013850 86351340 1 1 1 1 1 1 6 6 4 6 1 FITTING, QUICK DISCONNECT TUBE, CONDENSATE PUMP PUMP ASSY, DEHU HOSE, .5" ID X 5.25" LONG PLATE, BACK PLATE BRKT, PUMP MOUNT SCR, M6 X 16 PH, SS WASHER,SPRING LK,6MM,DIN127B,SS NUT, M8, LK, ISO7040,SST WASHER, M6, FNDR, ISO7039,SS TUBE, DISCHARGE SERVICE KIT 86352290 Trident LGR Dehumidifier SERIAL NO.
Refrigeration 9 7 5 11 3 8 14 16 1 14 13 14 13 15 14 12 4 10 6 12 13 16 14 36 2 17 12 86352290 Trident LGR Dehumidifier 16
Refrigeration REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86349390 86349270 86349250 86349240 86349190 86172950 86340990 86337520 86337500 86337490 86297930 86173330 86173320 86172870 86172820 86134850 86024750 1 1 1 1 2 4 1 2 1 1 1 8 12 20 2 15 2 DESCRIPTION SERIAL NO. FROM NOTES THERMISTOR ASSY FAN SHROUD W/SEALS RIGHT CAP W/SEAL LEFT CAP W/SEAL GASKET, EVAP COIL SCR, M5X12, SHCS, ISO4762, SS TRAY, CONDENSATE LINER CAPILLARY TUBE .
Wiring Diagram L N G sw sw/1 ws ws/2 ge/3 120V/60Hz -HOUR -MAIN SWITCH 10 2 GND 2 1 3 1.116 bn/4 sw/1 A 1.141 +N -PCB -SENSOR TP1 TP5 TP6 +PUMP +FAN sw/9 TP3 sw/10 TP7 TP2 +T +D TP8 TP4 +K1 +F ws/18 -C1 -X1 1.107 1.
Wiring Diagram REF PART NO. QTY - 86337830 86351670 1 1 DESCRIPTION SERIAL NO.
Suggested Spare Parts PART NO. 86349620 86343660 86341930 86256940 86315470 86309790 86219480 86001660 86013850 86341780 86341770 86340860 86276290 86173310 86337460 86349390 86351420 86341910 86341900 86341710 86351340 40 DESCRIPTION SERIAL NO. FROM CORD ASSY, 14/3 SJT X 30' BLK CAPACITOR, 45 µF CAPACITOR, 25 µF SWITCH SPOT ROCKER METER, HOUR ICD WHEEL, 12" X 2.25" HUBCAP, 9.
Serial Numbers REF. NO.
