Installation Instructions and Homeowner’s Manual WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONS BEFORE USING THIS APPLIANCE IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. Important instructions ……………………………………………………………3 General…………………………………………………………………………….…3 Locating Your Electric Fireplace…………………………………… …………… 3 Clearance To Combustibles………………………………………… …………... 4 Electrical Connections…..
GENERAL 1. 2. 3. Read all instructions before using this 13. Do not insert or allow foreign objects to enter any appliance. ventilation or exhaust opening as this may cause This appliance is hot when in use. To avoid electric shock, fire or damage to the appliance. burns, do not let bare skin touch hot surfaces. 14. To prevent fire, do not block air intakes or exhaust Keep combustible materials, such as furniture, in any manner.
CLEARANCE TO COMBUSTIBLES WARNING: Electrical outlet wiring must comply with local building codes and all other applicable regulations to reduce the risk of fire, electrical shock and injury. Back…………………………0mm Sides……………..…………0mm Floor……………. .…………0mm WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system if necessary. Top………………. .
GLASS INFORMATION MAINTENANCE OF MOTORS The motors used on the fan and flame genera- 1. Under no circumstances should this product tor assembly are prelubricated for extended be operated with missing or broken glass. bearing life and require no further lubrication. 2. Do not strike or slam the glass. 3. Do not use abrasive cleaners to clean the glass. However, periodic cleaning/vacuuming of the fan/heater unit is recommended. WARNING: Make sure that the 4.
Operating Instructions This section provides easy step by step instructions for operating your fireplace. 1. Make sure the unit is unplugged from the power source。 2. Plug the fireplace into a 10AMP/220V outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1900 watts. To access the controls, open the bottom of the fireplace at the front of the unit (see Figure A). A. MAIN ON/OFF SWITCH The on/off switch supplies power to all fireplace functions (heater/flame). B.
SPECIFICATIONS: Model: V50TYLA-C Voltage: 220V/50HZ Model: V50TYLA-O Total Amps: 6.5A Voltage: 220V/50HZ Total Amps: 6.5A Total Watts: 1350W Heating Ratings: 1200W Total Watts: 1350W Heating Ratings: 1200W Dimensions, CM (H x W X D) Dimensions, CM (H x W X D) Fireplace Fireplace 97.8x67x35.9 Carton 105.1x74.5x44.1 97.8x67x35.9 Carton Weight, Kgs 105.1x74.5x44.1 Weight, Kgs Fireplace 35.9 Fireplace 35.9 Shipping 43.1 Shipping 43.
REPLACEMENT PARTS PICTURES OF V50TYLA-O V50TYLA-C V50TYLA-DO V50TYLAR-BC 2 9 6 V50TYLA-BC 7 5 4 8
V50TYLA-O Ite m # P a rt 1 Log 2 Fan/Heater A s s em bly NFHTX186-R/V B 17-000-R 3 S y nc hroniz ation M otor-220V olt A C w/Term inal FE 23A 307 4 Cord P ower H05V V -F3GX1.
V50TYLA-C Item# Part Descripition Part Number 1 Log Set VL050-01A 2 Fan/Heater Assembly NFHTX186-R/VB17-000-R 3 Synchronization Motor-220Volt AC w/Terminal FE23A307 4 Cord Power H05VV-F3GX1.
V50TYLA-DO Item# Part Descripition Part Number 1 Log Set VL050-01A 2 Fan/Heater Assembly NFHTX186-R/VB17-000-R 3 Synchronization Motor-220Volt AC w/Terminal FE23A307 4 Cord Power H05VV-F3GX1.
V50TYLA-BC Item# Part Descripition Part Number 1 Log Set VL050-01A 2 Fan/Heater Assembly NFHTX186-R/VB17-000-R 3 Synchronization Motor-220Volt AC w/Terminal FE23A307 4 Cord Power H05VV-F3GX1.
V50TYLAR-BC Item# Part Descripition Part Number 1 Log Set VL050-01A 2 Fan/Heater Assembly NFHTX186-R/VB17-000-R 3 Synchronization Motor-220Volt AC w/Terminal FE23A307 4 Cord Power H05VV-F3GX1.