User Manual
Table Of Contents
- DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
- GENERAL SAFETY INSTRUCTIONS
- IN CASE OF FAULT
- PACKAGING, SHIPPING AND COMPLAINT
- WARRANTY AND PRODUCTS RETURN
- MAINTENANCE AND DISCLAIMER
- POWER SUPPLY
- CONFORMITY
- INTRODUCTION
- DESCRIPTION
- INSTRUCTIONS
- 1. LINE IN (XLR-JACK combo input)
- 2. LINK LEFT (XLR output balanced)
- 3. OUT LEFT (XLR output balanced)
- 4. INPUT RIGHT (combo XLR-JACK input)
- 5. LINK RIGHT (XLR output balanced)
- 6. OUT RIGHT (XLR output balanced)
- 7. GND LIFT switch
- 8. FILTER switch
- 9. LEVEL control
- 10. SIGN/CLIP indicator
- 11. PHASE 0° / 180° switch
- 12. ON indicator
- 13. POWER switch
- 14. LINE VOLTAGE selector
- 15. FUSE holder
- 16. AC~ socket
- 17. TECHNICAL SPECIFICATION
- 18. ACCESSORIES
- TRATTAMENTO DEL DISPOSITIVO ELETTRICO OD ELETTRONICO A FINE VITA
- AVVERTENZE PER LA SICUREZZA
- IN CASO DI GUASTO
- IMBALLAGGIO, TRASPORTO E RECLAMI
- GARANZIE E RESI
- MANUTENZIONE E LIMITAZIONI D’USO
- ALIMENTAZIONE
- CONFORMITÀ CE
- INTRODUZIONE
- DESCRIZIONE
- ISTRUZIONI
- 1. INPUT LEFT (ingresso linea combo XLR-JACK)
- 2. LINK LEFT (uscita bilanciata XLR)
- 3. OUT LEFT (uscita bilanciata XLR)
- 4. INPUT RIGHT (ingresso linea combo XLR-JACK)
- 5. LINK RIGHT (uscita bilanciata XLR)
- 6. OUT RIGHT (uscita bilanciata XLR)
- 7. GND LIFT (interruttore sollevamento massa)
- 8. FILTER (interruttore frequenza di crossover)
- 9. LEVEL (controllo di livello)
- 10. SIGN/CLIP (indicatore di segnale e clip limiter)
- 11. PHASE 0° / 180° (interruttore inversione polarità)
- 12. ON (indicatore di accensione)
- 13. POWER (interruttore di accensione)
- 14. Selettore tensione di rete LINE VOLTAGE
- 15. FUSE (portafusibili)
- 16. AC~ (presa di alimentazione di rete)
- 17. SPECIFICHE TECNICHE
- 18. ACCESSORI
- Mechanical Dimensions – Dimensioni Meccaniche
- Configurations – Configurazioni
- Connectors - Connettori
detailed description. This warranty does not extend to damage resulting from improper installation,
misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been
properly used and warranty is still valid, then the unit will be replaced or repaired. Proel S.p.A. is not
responsible for any "direct damage" or "indirect damage" caused by product defectiveness.
MAINTENANCE AND DISCLAIMER
• Clean only with dry cloth.
• Proel products have been expressly designed for audio application, with signals in audio range (20Hz to
20kHz). Proel has no liability for damages caused in case of lack of maintenance, modifications, improper
use or improper installation non-applying safety instructions.
• Proel S.p.A. reserves the right to change these specifications at any time without notice.
• Proel S.p.A. declines any liability for damages to objects or persons caused by lack of maintenance,
improper use, installation not performed with safety precautions and at the state of the art.
POWER SUPPLY
• This apparatus should only be connected to power source type specified in this owner’s manual or on the unit.
• If the supplied AC power cable plug is different from the wall socket, please contact an electrician to
change the AC power plug.
• Hold the plug and the wall outlet while disconnecting the unit from AC power.
• If the unit will not be used for a long period of time, please unplug the power cord from AC power outlet.
• To avoid unit power cord damage, please do not strain the AC power cable and do not bundle it, do not
step on it or pinch it by heavy objects.
• The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
CONFORMITY
• The product is in compliance with CE Directive LVD 2014 / 35 / CE as stated in EN 60065 standard.
• The product is in compliance with CE Directive EMC 2014 / 30 / CE as stated in EN 55103-1 and EN
55103-2 standards.
FCC COMPLIANCE NOTICE
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired
operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cau
se harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
5