Manual

ManualsBrandsProface ManualsComputer HardwareAGP3500 - 10.4 DIO HMI"

ST-3500 Series

Installation Guide

Package Contents

(1) ST Unit (1)

(2) English and Japanese Installation Guides

(one of each) <This Guide>

(3) Warning/Caution Information (1)

(4) Installation Gasket (1)

(Attached to the ST unit)

(5) Installation Fasteners (Set of 4)

(6) Power Connector (1)

(Attached to the ST unit for DC model)

(7) USB Cable Clamp (1 set)

(Holder: 1, Clamp: 1)

This unit has been carefully packed, with

special attention to quality. However, should

you find anything damaged or missing,

please contact your local ST distributor

immediately.

About the Manual

For the detailed information on ST3000

series, refer to the following manual.

• ST3000 Series Hardware Manual

• Maintenance/Troubleshooting

ST3000 Series Hardware Manual can be

selected from the help menu of GP-Pro EX or

downloaded from Pro-face Home Page.

URL

http://www.pro-face.com/otasuke/

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet before

using the product.

Summary of content (12 pages)

PAGE 1
About the Manual ST-3500 Series Installation Guide For the detailed information on ST3000 series, refer to the following manual. • ST3000 Series Hardware Manual • Maintenance/Troubleshooting ST3000 Series Hardware Manual can be selected from the help menu of GP-Pro EX or downloaded from Pro-face Home Page. URL http://www.pro-face.com/otasuke/ Caution Be sure to read the “Warning/Caution Information” on the attached sheet before using the product.
PAGE 2
Part Names and Functions Front Rear A C AST-3501T (AC model) D F E G B H Bottom (With CF Card Cover open) AST-3501T (AC model) Name Description LED A Status LED B USB Host Interface (USB) C CF Card Access LED D Power Connector E F G H CF Card Cover Serial Interface (COM1) Serial Interface (COM2) Dip Switches ST Status Green (lit) Normal operation (power is ON.) or OFFLINE operation. Orange (blinking) During software startup. Red (lit) When power is turned ON. Not lit Power is OFF.
PAGE 3
General Specifications Electrical Specifications DC model AC model DC24V AC100 to 240V Rated Voltage DC19.2 to 28.8V AC85 to 265V Allowable Voltage Drop 10ms (max.) 1 cycle or less (Voltage drop interval must be 1s or more.) Power Consumption 45W (max.) AC100V 0.90A or less (TYP 0.48A) AC240V 0.45A or less (TYP 0.26A) In-Rush Current 30A (max.) 60A (max.
PAGE 4
External Interfaces • This ST unit’s serial interface is not isolated.When the host (PLC) unit is also not isolated, and to reduce the risk of damaging the RS232C/RS422/RS485 circuit, be sure to connect pin #5 SG (Signal Ground) terminal. • Similarly shaped connectors are used for COM1 and COM2 of the ST. Therefore, be sure to connect the correct connectors. Communication is not available unless the connectors are connected correctly.
PAGE 5
COM2 Recommended Cable Connector XM2D-0901 Recommended Jack Screw XM2Z-0073 Recommended Cable Cover XM2S-0913 Interfit Bracket Pin # #4-40 inch screws are used.
PAGE 6
2. Installations 1. ST Installation (1) Create a Panel Cut following the dimensions in the table below. Installation Requirements Unit: mm [in.] X Under Panel 4-R3[0.12] thickness Y Panel thickness Y • For easier maintenance, operation, and improved ventilation, be sure to install the ST at least 100 mm [3.94 in.] away from adjacent structures and other equipment. Unit:mm[in.] ST 100 [3.94] 100 [3.94] 100 [3.94] 100 [3.94] 100 [3.94] X +1 +1 259.0 -0 201.0 -0 [10.20 +0.04] [7.91 +0.
PAGE 7
Wiring Insertion Slot Recess Hook the fastener on the Recess, Panel ST y To avoid an electric shock, prior to connecting the ST unit’s power cord terminals to the power terminal block, confirm that the ST unit’s power supply is completely turned OFF, via a breaker, or similar unit. y Any other power level can damage both the ST and the power supply. y When the FG terminal is connected, be sure the wire is grounded. Installation Fastener Hook and secure the fastener on the panel with a screw.
PAGE 8
Connecting the ST Power Cord Power Connector (Plug) Specifications (1) Be sure that the ST's power cord is not plugged in to the power supply. (2) Remove the Terminal Strip's clear plastic cover. (3) Remove the screws from the two (2) terminals (L,N) and FG (Frame Ground) Terminal, position the Ring Terminals and reattach the screws.
PAGE 9
Connecting the ST Power Cord 3. (1) Confirm that the ST unit’s Power Cord is unplugged from the power supply. (2) Remove the power connector (plug) from the main unit. (3) Loosen the three screws in the center of the Power Connector. (4) Strip the power cord, twist the conductor’s wire ends, insert them into the pin terminal and crimp the terminal. Attach the terminal to the power connector. (5) Fix it with screws.
PAGE 10
4. Grounding Cautions 5. • All ST Input and Output signal lines must be separated from all operating circuit (power) cables. • If this is not possible, use a shielded cable and ground the shield. • Be sure to create an exclusive ground for the Power Cord’s FG terminal. Use a grounding resistance of 100Ω, a wire of 2mm2 or thicker, or your country’s applicable standard. • The SG (signal ground) and FG (frame ground) terminals are connected internally in the ST unit.
PAGE 11
UL/c-UL Approval Be aware of the following items when building the ST into an end-use product: • The ST unit’s rear face is not approved as an enclosure. When building the ST unit into an end-use product, be sure to use an enclosure that satisfies standards as the end-use product’s overall enclosure. • The ST unit must be used indoors only. • Install and operate the ST with its front panel facing outwards.
PAGE 12
Revision Inquiry The revision code of the ST is shown in the label affixed to the ST. In the example shown below, an asterisk "*" is displayed in the position where "A" should be, meaning "Rev. A". Do you have any questions about difficulties with this product? Please access our site anytime that you need help with a solution. http://www.pro-face.