Owner's manual

ManualsBrandsProface ManualsComputer HardwareAGP3500 - 10.4 DIO HMI"

AGP3300-U1-D24

Installation Guide

Package Contents

(1) GP Unit (1)

(2) English and Japanese installation

Guides (1 of each) <This Guide>

(3) Warning/Caution Information (1)

(4) Installation Gasket (1, attached to the

GP unit)

(5) Installation Fasteners (Set of 4)

(6) Power Connector (1)

(Attached to the GP unit)

(7) USB Cable Clamp (1 port) (1)

This unit has been carefully packed, with

special attention to quality. However,

should you find anything damaged or

missing, please contact your local GP

distributor immediately.

About the Manual

For detailed information on the GP3000

series, refer to the following manuals:

• GP3000 Series Hardware Manual

• Maintenance/Troubleshooting

• Device/PLC Connection Manual

The manuals can be selected from the

help menu of GP-Pro EX or downloaded

from Pro-face Home Page.

URL

http://www.pro-face.com/otasuke/

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet

before using the product.

Summary of content (12 pages)

PAGE 1
About the Manual AGP3300-U1-D24 Installation Guide For detailed information on the GP3000 series, refer to the following manuals: • GP3000 Series Hardware Manual • Maintenance/Troubleshooting • Device/PLC Connection Manual The manuals can be selected from the help menu of GP-Pro EX or downloaded from Pro-face Home Page. URL http://www.pro-face.com/otasuke/ Caution Be sure to read the “Warning/Caution Information” on the attached sheet before using the product.
PAGE 2
Part Names and Functions Rear Front B C A F D I G E H Left side J Bottom Right side Name Description Color Indicator Green A Status LED ON Flashing ON Red Flashing ON Orange Flashing Operation Mode Logic execution mode (Drawing) (when logic is enabled) OFFLINE In operation RUN In operation STOP When power is turned on.
PAGE 3
E Power Connector (Socket) F USB Host Interface (USB) G Serial Interface (COM1) H Serial Interface (COM2) I CF Card Cover J DIP Switches Complies with USB 1.1. Uses a “TYPE-A” connector. Power supply voltage:DC5V ±5%, Output current:500mA (max.) The maximum communication distance: 5m D-sub 9-pin plug type. RS232C, RS422, and RS485 are switched by software. D-sub 9-pin socket type. RS422 and RS485 are supported. Located inside the CF Card Cover.
PAGE 4
General Specifications Power Supply Electrical Specifications Input Voltage DC24V Rated Voltage DC19.2 to 28.8V Allowable Voltage Drop 5ms (max.) Power Consumption 26W (max.) In-Rush Current 30A (max.) Voltage Endurance AC1000V 20mA for 1 minute (between charging and FG terminals) Insulation Resistance DC500V 10MΩ (min.
PAGE 5
External Interfaces • For instructions on how to connect to other devices, always refer to the “GP-Pro EX Device/PLC Connection Manual”. • Always connect the #5 SG (Signal Ground) of the GP unit to the connected device, especially if the connected device is also not isolated. Failure to do so may damage the RS232C/RS422/RS485 circuit. COM1 Recommended Cable Connector XM2D-0901 Recommended Jack Screw XM2Z-0073
PAGE 6
COM2 • Always connect close to the GP unit's COM port when terminating with the termination pins (TRMRX/TRMTX). Recommended Cable Connector XM2A-0901 Recommended Jack Screw XM2Z-0073 Recommended Cable Cover XM2S-0913
PAGE 7
2. Installations 1. GP Installation (1) Create a Panel Cut and insert the GP into the panel from the front. Determine the panel thickness according to the panel thickness range with due consideration of panel strength. Installation Requirements • For easier maintenance, operation, and improved ventilation, be sure to install the GP at least 100mm [3.94in.] away from adjacent structures and other equipment. Unit: mm [in.] X r ≤ 3 [0.12] Panel thickness Unit:mm[in.] 100 [3.94] 100 [3.94] Y 100 [3.
PAGE 8
(3) The following figures show the four (4) fastener insertion slot locations. Insert each fastener’s hook into the slot and tighten it with a screwdriver. Insert the installation fasteners securely into the insertion slot recess. Wiring • To avoid an electric shock, prior to connecting the GP unit’s power cord terminals to the power terminal block, confirm that the GP unit’s power supply is completely turned OFF, via a breaker, or similar unit.
PAGE 9
(4) Attach the Power connector (Plug) to the GP. • The power connector (plug) is CA5DCCNM-01 made by Pro-face or MSTB2,5/3-ST-5,08 made by Phoenix Contact. When connecting the Power Cord, use the following items when performing wiring: (Items are made by Phoenix Contact.) Recomended Driver SZF 1-0.6x3.5 (1204517) Recomended Pin Terminals AI 0.75-8GY (3200519) AI 1-8RD (3200030) AI 1.5-8BK (3200043) AI 2.
PAGE 10
• Connect a surge absorber to handle power surges. Common Grounding (OK) GP unit • Be sure to ground the surge absorber (E1) separately from the GP unit (E2). Select a surge absorber that has a maximum circuit voltage greater then that of the peak voltage of the power supply. Other Equipment Common Grounding (Not OK) GP unit GP Other Equipment FG E1 E2 Lightening Surge Absorber 4. 3.
PAGE 11
(2) Pass the band of the USB cable clamp through the bridge of the USB holder. UL/c-UL Approval The AGP3300-U1-D24 unit is a UL/c-UL listed product. (UL File No.E220851) Bridge USB Holder Product Model No. (3) Insert the USB cable into the port. Fasten the band around the plug and secure it with the clamp. UL/c-UL Registration Model No. AGP3300-U1-D24 3710015-01 USB Holder These products conform to the following standards: • UL508 Industrial Control Equipment • CSA-C22.2 No.
PAGE 12
CE Marking Inquiry • The AGP3300-U1-D24 unit is a CE marked, EMC compliant product. This unit also conforms to EN55011 Class A, EN61000-6-2 directives. Do you have any questions about difficulties with your GP? Please access our site anytime that you need help with a solution. http://www.pro-face.com/otasuke/ Note Please be aware that Digital Electronics Corporation shall not be held liable by the user for any damages, losses, or third party claims arising from the uses of this product.