Owner manual

ManualsBrandsProface ManualsComputer HardwareAGP3500 - 10.4 DIO HMI"

GP-3300/3400 Series

Installation Guide

Package Contents

(1) GP Unit (1)

(2) English and Japanese installation

Guides (1 of each) <This Guide>

(3) Warning/Caution Information (1)

(4) Installation Gasket (1, attached to the

GP unit)

(5) Installation Fasteners (Set of 4)

(6) RCA-BNC Convertor (1)

(AGP-3360T/AGP-3450T)

(7) AUX Connector (1)

(GP-3400 Series)

(8) Power Connector (1)

(Attached to the GP unit for GP-3300

Series)

(9) USB Cable Clamp (2 port) (1 set)

(Holder: 1, Cover: 2)

(GP-3400 Series)

(10)USB Cable Clamp (1 port) (1)

(Holder: 1, Clamp: 1) (All GP-3300

Series, except AGP-3310T/3360T)

(11)USB Cable Clamp (1 port)

(Clip: 2, Tie: 2)

(AGP-3310T/3360T)

This unit has been carefully packed, with

special attention to quality. However,

should you find anything damaged or

missing, please contact your local GP

distributor immediately.

About the Manual

For the detailed information on GP3000

series, refer to the following manuals.

• GP3000 Series Hardware Manual

• Maintenance/Troubleshooting

The manuals can be selected from the

help menu of GP-Pro EX or downloaded

from Pro-face Home Page.

URL

http://www.pro-face.com/otasuke/

• When using GP-3300 Series with Pro-

Designer, refer to “AGP-3300 Series

User Manual” (PDF File). AGP-3300

Series User Manual can be selected

from [Manual] in the [Install] dialog box

displayed after the CD-ROM of Pro-

Designer is inserted.

Caution

Be sure to read the “Warning/Caution

Information” on the attached sheet

before using the product.

Summary of content (16 pages)

PAGE 1
(9) USB Cable Clamp (2 port) (1 set) (Holder: 1, Cover: 2) (GP-3400 Series) GP-3300/3400 Series Installation Guide Caution (10)USB Cable Clamp (1 port) (1) (Holder: 1, Clamp: 1) (All GP-3300 Series, except AGP-3310T/3360T) Be sure to read the “Warning/Caution Information” on the attached sheet before using the product.
PAGE 2
Part Names and Functions Front Rear Right Side B Bottom (CF Card Cover Open) F G C A AGP-3300T AGP-3300T C D F I E J AGP-3450T AGP-3450T Name A Status LED G J AGP-3300T H A AGP-3450T E H AGP-3300T B I AGP-3450T Description Mode Logic execution mode Color Indicator Operation (Drawing) (when logic is enabled) OFFLINE ON Green In operation RUN Flashing In operation STOP ON When power is turned on.
PAGE 3
Complies with USB 1.1. Uses a “TYPE-A” connector. Power supply voltage:5 VDC ±5 %, Output current:500 mA(max.) The maximum communication distance: 5m D-sub 9-pin plug type. RS232C, RS422, and RS485 are switched by software. (AGP-3302B supports RS232C only.) D-sub 9-pin socket type. RS422 and RS485 are supported. (AGP-3302B has D-sub 9-pin plug type and supports RS422 only.) (Except for AGP-3302B) Located inside the CF Card Cover.
PAGE 4
General Specifications Electrical Specifications Power Supply AGP-3300∗/3301∗/ 3310T/3360T AGP-3302B Input Voltage DC 24 V Rated Voltage DC 19.2 to 28.8 V Allowable Voltage Drop 5 ms (max.) 10 ms (max.) Power Consumption 26 W (max.) 18 W (max.) In-Rush Current 30 A (max.) Voltage Endurance AGP-3400∗/3450T 28 W (max.) AC 1000 V 20 mA for 1 minute (between charging and FG terminals) Insulation Resistance DC 500 V 10 MΩ (min.
PAGE 5
External Interfaces • For instructions on how to connect to other devices, always refer to the “GP-Pro EX Device/PLC Connection Manual”. • Always connect the #5 SG (Signal Ground) of the GP unit to the connected device, especially if the connected device is also not isolated. Failure to do so may damage the RS232C/RS422/RS485 circuit. COM1 Recommended Cable Connector XM2D-0901 Recommended Jack Screw XM2Z-0073
PAGE 6
COM2 • Always connect close to the GP unit's COM port when terminating with the termination pins (TRMRX/TRMTX). Recommended Cable Connector XM2A-0901 Recommended Jack Screw XM2Z-0073 XM2D-0901 (AGP-3302B only) Recommended Cable Cover XM2S-0913
PAGE 7
AUX Input/Output and Sound Output Interface (Supported by GP-3400 series only) GP Unit Side Connector S2L3.5/12/90F Terminal Block B2L3.
PAGE 8
Unit: mm [in.] Installations Installation Requirements Y 1. Panel r≤3 [0.12] thickness X • For easier maintenance, operation, and improved ventilation, be sure to install the GP at least 100 mm [3.94 in.] away from adjacent structures and other equipment. GP Unit:mm[in.] 100 [3.94] GP 100 [3.94] 100 [3.94] GP-3300 Series 100 [3.94] 100 [3.94] GP-3400 Series 100 [3.94] 100 [3.94] Y +1 156.0 -0 +1 123.5 -0 +1 204.5 -0 +1 159.5 -0 Panel thickness 1.6 [0.06] to +0.04 +0.04 [6.14-0 ] [4.
PAGE 9
Wiring and attachment Insertion Slot Recess (1) Insert the tip of the screwdriver into one of the square holes. Then, insert the cable into the corresponding round hole. When you pull out the screwdriver, the cable is locked. For the pin assignment of the AUX connector, refer to “External Interfaces”. Hook the fastener on the Recess, Panel GP Installation Fastener Hook and secure the fastener on the panel with a screw.
PAGE 10
Wiring • The power connector (plug) is CA5DCCNM-01 made by Pro-face or MSTB2,5/3-ST-5,08 made by Phoenix Contact. When connecting the Power Cord, use the following items when performing wiring. (Items are made by Phoenix Contact.) • To avoid an electric shock, prior to connecting the GP unit’s power cord terminals to the power terminal block, confirm that the GP unit’s power supply is completely turned OFF, via a breaker, or similar unit. • Any other power level can damage both the GP and the power supply.
PAGE 11
(4) Attach the Power connector (Plug) to the GP. - + • Be sure to ground the surge absorber (E1) separately from the GP unit (E2). Select a surge absorber that has a maximum circuit voltage greater then that of the peak voltage of the power supply. Power Connector (Socket) FG GP FG E1 Power connector (Plug) 2. AGP-3300T E2 Lightening Surge Absorber Power Supply Cautions 3. • Input and Output signal lines must be separated from the power control cables for operational circuits.
PAGE 12
1. Common Grounding (OK) GP unit Other Equipment GP-3300 Series units (Except for AGP-3310T/AGP-3360T) Attaching the USB Cable Clamp (1) Insert the USB holder into the slot in front of the GP unit’s USB port and pull it down and forward. Common Grounding (Not OK) GP unit 4. 2 Other Equipment 1 (2) Pass the band of the USB cable clamp through the bridge of the USB holder.
PAGE 13
2. AGP-3310T/3360T units can pass through the center of the tie loop. • Be careful for the edge of the clip not to cut the fingers. Attaching the USB Cable Clip (1) Mount the clip to the USB mark connector shell so that it overlaps. The clip is corresponding to 27 to 43.5mm [1.06 to 1.71 in.
PAGE 14
(5) Following the diagram, completely tighten the tie and thoroughly affix the clip on the connector shell. (1) Before starting the procedure, orient the two tabs on both sides of the USB Holder in the direction of the arrows in the figure and remove the USB Cover. Tabs (2) Attach the USB holder to the USB Host Interface part of the main unit. Hook the lower pick of the USB holder to the attachment hole of the main unit and then insert the upper pick as shown below to fix the USB holder.
PAGE 15
Be aware of the following items when building the GP into an end-use product: • The GP unit’s rear face is not approved as an enclosure. When building the GP unit into an end-use product, be sure to use an enclosure that satisfies standards as the end-use product’s overall enclosure. • The GP unit must be used indoors only. • Install and operate the GP with its front panel facing outwards. • If the GP is mounted so as to cool itself naturally, be sure to install it in a vertical panel.
PAGE 16
(5) WARNING: Explosion hazardconfirm that the power supply has been turned OFF before disconnecting equipment, or confirm that the location is not subject to the risk of explosion. (6) “WARNING: Explosion hazard-do not disconnect equipment unless power has been switched off or the area is known to be Non-Hazardous”. (7) In the case of use in Hazardous Locations, be sure to check that the externally connected unit and each interface have been fixed with screws and locked.