User manual

5
4.3 LED Funktionskontrolle und Ladestatus
Rot bis Grün an After pressing the ON OFF button lights up the spectrum. It
disappears after about 3 seconds.
By pressing the SOS button is lit again, and the spectrum shows
the current charge level of the jumper device. Green 81-100%
jumpstart function OK.
Yellow LED lights 61 - 80% charged.
jumpstart function OK.
Orange LED lights, 41 - 60% charged. Every 6 months, the unit
should be charged and to prevent a discharge damage to the
device battery. Jumpstart function OK but limited power.
Red LED lights 21 - 40% charged. Red LED flashes on the
instrument housing laterally loaded below 20%. If the red box
is on, the start device must be charged! ORANGE or RED lights
illuminated, the device can not be used to jump-start! Device
deactivated. Recharge soonest.
6
Lithium batteries are subject to minimal self-discharge. Every 6 months later than the start device is to
be loaded in order to avoid a full discharge of the battery device. Possible damage to the start device
which arise due to full discharge or overheating is not in the warranty. Store the start device always
in a cool environment at about 15 ° C to 20 ° C Vehicles often feature electronic electrical facilities.
These can be damaged by high rise surges and spikes. Please read carefully before you connect the
device to a vehicle, the manual of the vehicle, whether a jump-start aid is permitted. Note before
connecting the safety warnings in this manual and your vehicle and battery manufacturer this unit to a
12V car battery. Note the warning symbols on start device!
4.1 This jump starter is fully automatic. There is only from jumpstart power when the power switch
first and then Jump Start switch was activated and recognizes a corresponding resistance (car battery).
The jumper cables remain without power supply while the device is not connected to a 12V vehicle
battery and the switch is not pressed. Connect the device only to jump start the battery terminals.
The start device never connected to the vehicle body! Exclusively connect to the battery in the correct
polarity!
The start device has several protection mechanisms:
Overcharge protection / under voltage protection Overload the lithium battery is prevented by the
charger. At too low a charge of the battery, the device switches off automatically.
Spark protection.
In mutual contact and terminal clips no sparks are generated.
Reverse polarity protection Connecting them incorrectly, confusing the polarity, the device switches off
immediately. The battery and the start device will be protected.
Overheating protection
The device switches off automatically when the max. Operating temperature is exceeded the device
housing. It automatically turns on again when it has cooled down accordingly.
4.2 Features
1. Fire retardant plastic housing
2 Automatic shut off to save energy. Approx. 5 seconds after starting a car engine.
3 High-start performance, high power reserve for USB devices
4 Integrated emergency work light side of the housing
6 Spark protection
7 Reverse polarity, short circuit protection.
8 Automatic undervoltage lockout integrated devices battery
9 Overheat protection, automatic shutdown in case of overheating of the device
10th Convenient connectors for jumper cables
11th Depending on the ambient temperature, up to 10 start-up aid in succession with a
batterycharge possible.
12th 5V 2000mA USB 2.0 output, for operating or charging USB device.
13th Lithium battery with high life expectancy by following the instructions.
14th LED Warning light , LED side light (worklight)
15th Cable with OBDII connector (only with JPR9000)
16th By removable caps from dust and moisture-proof equipment outputs
5 Connection / Operation in single steps:
5.1 Before starting aid
- Make sure the log book of the vehicle manufacturer if a jump start is permitted.
- Wear suitable protective clothing.
- Clean the terminals (battery terminals and cable connections) before the start.
- In open batteries: Fill in distilled water until the level specified by battery manufacturer is reached.
For maintenance-free batteries, please follow exactly the instructions of the battery manufacturer.
- Make sure that the start device is fully charged. (Power LED Green)
- Connect to the battery - first the red terminal clamp to the positive terminal (+), then the black
binding post (). The correct sequence!
- Make sure that the battery terminals are securely connected to the battery terminals before
Press the start help function!
- Make sure that all electrical consumers of the vehicle are turned off or disconnected from the electrical
system! Also include the interior, Motorrau or trunk lights, radio, navigation, driving and parking
lights, hazard lights, ventilation, heated seats, etc.
- Make sure that the vehicle circuit is idle, no gear is engaged.
- The hand brake is on! The vehicle is secured against rolling.
- Take care that no clothing jewelry, body parts, charging cable caught in the vicinity of rotating
engine parts.
- Upon completion of the jumpstart process, first disconnect the black jumper cable from the battery
first and then disconnect the red cable from the battery. Observe the sequence!
axhess GmbH & Co. KG, Industriestrasse 11, 56598 Rheinbrohl, www.axhess.de