User manual

9 10
The LED charge status display signals the respective charge state by a flashing LED. When charging
is complete, the green LED in the function control. With green LED light-up the start device is ready to
start. The start device after each jump-start operation at least until the yellow mark upload it to always
be kept ready. Latest when the side of the unit mounted red LED labeled Low, the start device must
be charged urgently to avoid damage to the battery. The booster function and the USB port are not
available at this stage. Have you missed the charge of the star using the device and the low light is off,
the lithium battery penetrate to load. Turn off the start device is NOT on, turn the LED lighting
on NOT to avoid damage to the internal battery. The start device should be regularly charged at
least every six months at least until the yellow mark. For longer periods of time connected
to the charger is not recommended by the aging of the battery is not to speed. (S. Lagerung) to avoid.
5.8 Storage of the jumper device
Note that lithium batteries react sensitive to high temperatures. Store in a cool-start the device. Keep
the unit away from heat sources or additional sunlight. The battery will age faster the higher their cell
voltage, so it should be avoided to keep continually charged 100 percent of a Li battery. Cold storage
is advantageous. The self-discharge of the lithium battery is only about 3% per month. We recommend
storage at 15 ° C - 20 ° C at a load level of about 60% = YELLOW LED display. Lithium batteries should not
be discharged below 2.5V per cell, even when stored. The electrolytes in the cell must not freeze, which
occurs at a temperature around -25 ° C. Store or store because of the temperature sensitivity of the lithium
batteries therefore not permanent in the emergency starter vehicle. Every 6 months to start using the
device at least up to the mark YELLOW be loaded.
5.9 The USB output
The start device has a USB 2.0 output, 5V 2000mA max., The operation of loading or capable of many 5V
USB products, with max. Power consumption of max. 2.0 A, is determined. The USB output is activated
by pressing the POWER switch. He can power USB devices for many hours. The supply duration varies
depending on the charge level of the booster unit, power and intensity of the connecting device. During a
starting operation means, the supply of a USB device connected previously to be interrupted. Do not use
the USB output at start. During charging, connect the jump start device to the charger, the USB output
can be used. Use the USB output, even if you are not sure if the remaining battery jump start device is not
in use for a longer appears too high. Charge your mobile phone, tablet PC or other USB devices to the
battery level indicator shows the yellow range. (S.Lagerung) The start device with its high capacity battery
can recharge devices, you also make it operational during the (holiday) drive USB compatible devices such
as mobile phone, tablet PC, Kewego, or other USB. It can also be used as power source for use if your USB
device on strike unexpectedly due to power shortage. It can be due to its compact dimensions and low
weight, be a easily transportable, additional energy source.
5.10 Ttransportation inside a vehicle
If the device is transported in a vehicle, place it in a suitable location so that it can not begin to move with
sudden speed and or direction changes. Keep or store the start device but not in the vehicle permanently.
(See above storage)
6 Care and Cleaning
Check the technical safety of the jumper device, eg Damage the jumper cable or the housing. Wipe the
device only with a dry cloth. Do not use liquid or chemical cleaners. Do not immerse the appliance in
liquids. Never spill liquids on the unit.
7 Troubleshooting
With this start device you have purchased a product which has been designed according to state of the art
and is reliable. However, there may be problems or disorders.
Therefore, we would like to describe here how to fix any problems: Troubleshooting
No function - If the red LED on the charger, the start device has been loaded?
- If the device is fully charged?
- Is it damaged?
- Check the mains socket of the charger, mains power is there?
- Is the jump start connector with the jumper cables correctly with the emergency starter connected?
Device has function solution
Jumpstart without success
- Is the start device is sufficiently charged?
- The vehicle ignition is on, this has been pressed?
- All electricity consumers in the vehicle?
- The connections to the vehicle properly with correct polarity? Check and correct if necessary
- Has the black terminal (black clip) contact, check correct if necessary
- Have the red terminal contact, check correct if necessary
- The ambient temperature outside the device limits (See technical data)
Other measures as described above are carried out exclusively by qualified personnel authorized by
the manufacturer.
Caution! The start device may not replace a starter battery! It should not be a substitute for a starter
battery used explosion! It may not be used in frozen battery (from about -25 ° C) explosion! Never connect
to the vehicle body! Fire hazard for the vehicle electrical system!
axhess GmbH & Co. KG, Industriestrasse 11, 56598 Rheinbrohl, www.axhess.de