Instructions

ManualsBrandsProfi Power ManualsCar Battery Charging & CareProfi Power Quick start system Mini Jump JPR2600 Jump start current (12 V)=234 A

This manual is a publication of axhess, industry 11, 56589 Rheinbrohl. www.axhess.de

All rights including translation. Reproductions of any kind, even in part, such as photoco

pying, microﬁlming or storage in electronic data processing equipment, without the ex

press written consent of axhess. Reproduction, even partial, is prohibited. This manual cor

responds to the technical status at printing. Changes in technology, features and design.

USER MANUAL

„Power Punch“

12VDC

Mini Jump Start

„Power Punch“

12VDC

Mini Jump Start

JPR 1800 P

JPR 2600 P

JPR 9000 P

JPR 9000 P, JPR 4500 P, JPR 4500 6V, JPR 2600 P, JPR 1800 P

mit 5V USB 2.0 Power Outlet 2000mA

for device variations

JPR 4500 P

Summary of content (8 pages)

PAGE 1
„Power Punch“ 12VDC Mini Jump Start „Power Punch“ 12VDC Mini Jump Start USER MANUAL JPR 1800 P JPR 4500 P for device variations JPR 2600 P JPR 9000 P, JPR 4500 P, JPR 4500 6V, JPR 2600 P, JPR 1800 P mit 5V USB 2.0 Power Outlet 2000mA This manual is a publication of axhess, industry 11, 56589 Rheinbrohl. www.axhess.de All rights including translation.
PAGE 2
12VDC Mini Jump Start „Power Punch“ Handling the Unit 1 2 3 4 5 6 7 8 9 jumper cable connector Function Control battery charged green battery - Pliers USB output Power on / oﬀ switch start switch side lighting Warning Blinker Read this manual before using the device, very carefully and keep it in order once needed even for disclosure to third parties, at any time for future reference. Charge 12 hours before ﬁrst use. For 12V systems only, except JPR 4500 6V for 6V-board systems.
PAGE 3
Do not expose the start device is not high or very low temperatures, strong vibrations or humidity. Always look for a safe placement of the device! The start device must be securely installed / placed so that it does not fall down or fall over. The device is not a toy. It does not belong in the hands of children. In industrial facilities, the safety regulations of any relevant professional association are observed.
PAGE 4
Lithium batteries are subject to minimal self-discharge. Every 6 months later than the start device is to be loaded in order to avoid a full discharge of the battery device. Possible damage to the start device which arise due to full discharge or overheating is not in the warranty. Store the start device always in a cool environment at about 15 ° C to 20 ° C Vehicles often feature electronic electrical facilities. These can be damaged by high rise surges and spikes.
PAGE 5
.2 Position of the jumper device The start device, as far as the cable length allows, connect the battery removed. The jumpstart Never place directly over or under the vehicle battery. From the battery leaking gas or ﬂuids could damage the start device. Start device should not be placed on the engine block. Place the unit so that it can not fall or overturn. 5.3 jumpstart Make sure before you use the-start device on the charging stand.
PAGE 6
The LED charge status display signals the respective charge state by a ﬂashing LED. When charging is complete, the green LED in the function control. With green LED light-up the start device is ready to start. The start device after each jump-start operation at least until the yellow mark upload it to always be kept ready. Latest when the side of the unit mounted red LED labeled Low, the start device must be charged urgently to avoid damage to the battery.
PAGE 7
8 Warranty: 10 Technical Data / Model Apply axhess general warranty conditions without Your legal rights are aﬀected. The warranty applies only to manufacturing or material defects. The warranty period is 24 months from date of purchase. For the built in lithium battery jump starter, the warranty is limited to 24 months from date of delivery. The required, battery maintenance as described here advancing, is required. Damaged batteries due to maintenance errors, are not included in the warranty.
PAGE 8
Ergänzender Hinweis: Verwendung einer Power Station zur Spannungsversorgung / Spannungserhaltung eines Fahrzeuges bei Batteriewechsel. Verbinden Sie ein 12V auf 12V Kabel mit der Power Station (12V Ausgang ) und der Bordsteckdose oder Zigarettenanzünder-Buchse des Fahrzeuges. Schalten Sie die Power Station ein, Freigabe Stromversorgung. Die Power Station muss voll geladen sein und über einen separaten 12V Ausgang verfügen. Geeignete Power Stationen sehen Sie bitte unter www.axhess.