, INSTALLATION INSTRUCTIONS / OWNER S MANUAL PCD970R AM/FM HIGH POWER FLIP DOWN DETACHABLE FACE CD PLAYER
INTRODUCTION Congratulations on your purchase of a Profile state-of-the-art single disc CD player. Your selection of a Profile car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Profile CD player in a new system, you are certain to notice immediate performance benefits. FEATURES 50W x 4 Power Output 4 Band Preset Equalizer Loud Function Flip Down Detachable Face Power Level Meter ISO/DIN Mounting Blinking Security L.E.D.
SAFETY PRECAUTIONS Secure the CD player. When installing your CD player in the vehicle, make sure it is mounted properly in the dash, using an after market installation kit if needed. When using the supplied mounting sleeve, it is a must that you also use the supplied back brace to support the back of the CD player. Use caution when mounting the CD player. Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment wires.
CARE AND MAINTENANCE Cleaning the CD player When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only the exterior surface of the unit with a dry, clean soft towel using no chemical solvents. Operating in extreme temperatures Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case, wait until the temperature in the vehicle is normal, then resume operation. Protect your CDs.
DISC CARE AND PLAY: Before playing, clean the disc with a clean, lint-free cloth. Wipe the disc in the direction of the arrow. Do not use solvents such as benzine or thinners. Commercially available cleaners or anti static spray will damage the unit. Insert a disc with the labeled surface up. Label surface up Do not try to insert another disc when one has already been inserted. Doing so may damage the unit. Handle the disc by its edge to keep the disc clean and do not touch the surface.
ELECTRICAL AND SIGNAL CONNECTIONS Before making the following connections, take time to look over the vehicle's wiring and determine the location and wires you will be connecting to. If you do not wish to cut or tap into the vehicles existing factory wiring, there are wiring kits available at your car audio retailer that will allow you to plug directly into the factory wiring harness. Make sure to test all wires before connecting to the CD Player. ! Connect Black wire to chassis ground.
TWO SPEAKER SYSTEM ANTENNA CONNECTOR AUX RCA INPUT R R CH RED L L CH WHITE MEMORY +12V YELLOW BLACK(GND) - + BATTERY +12V RED (B+) SWITCHED +12V (ON WITH IGNITION) BLUE AUTO ANTENNA FRONT LEFT SPEAKER CAUTION! Low level signal output for connection to amplifier or signal processors. BROWN + 15A Fuse FRONT RCA OUTPUT FILTER BOX BLACK REAR RCA OUTPUT 0.5A Fuse GRAY 0.
MOUNTING THE CD PLAYER There are two different ways to mount the CD Player. In most Japanese vehicles you can use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve and rear support bracket. When considering your mounting location, make sure the unit will be leveled.
Attach the back brace to the CD player using the supplied hardware. Then attach the other end of the brace to a firm mounting surface (i.e. Dash brace, fire wall, e.t.c.) This will brace the back of the CD player to ensure solid mounting to prevent theft and provide optimal CD play. Once the CD player is secured, fit the trim ring over outside edge of the radio until it snaps into place. To Attach the Face Plate: Basically, the face plate should be attached to the unit in the reverse order of removal.
ISO/DIN MOUNTING If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on the side of the CD player to attach to the existing factory mounting bracket, without using the provided DIN sleeve. ! Remove the factory ISO/DIN mounting bracket from the car along with the factory radio. ! Remove the factory radio from the bracket by unscrewing the two Phillips screws on each side of the radio paying close attention to their screw positions and saving the screws to mount the CD player.
LOCATION AND FUNCTION OF CONTROLS 10 PCD970R
1 POWER To turn ON the unit, press any button except the OPEN button. To turn OFF the unit, press the PWR button for more than 2 seconds. 2 FLIP DOWN PANEL Press the OPEN button to flip down the face plate. This will allow you to insert or eject a CD and also remove the face plate. 3 CD PLAY To play a CD, press the OPEN button to flip down the face plate exposing the CD inserting slot. Gently insert the CD into the slot with the label side facing up.
8 9 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND Under radio mode, press the I 8 or I 9 button momentarily and repeatedly to change the frequency number up or down one step. Under SEEK 1 mode, press and hold the I 8 or I 9 button for more than 2 seconds to seek to the next or previous clear station. Under SEEK 2 mode, press and hold the I 8 or I 9 button to speedily change stations up or down. Changing stations will stop once the button is released.
Press the SEL button for more than 2 seconds to display additional set of functions for adjustments, such as DSP, Beep On/Off, Seek 1 or 2 , Clock 12 or24, and Volume Last/Adjust. DSP - The unit is equipped with 4 preset equalization modes. Press the SEL button for more than 2 seconds to display DSP OFF. Then turn the VOL knob 5 in , the clockwise direction to choose one of 4 following preset EQ s in the following order. When using preset EQ modes you will not have access to Bass and Treble settings.
12 CD TOP/PAUSE In CD play mode, press the TOP resume normal play. 12 button to pause CD play. Press again to In CD play mode, press the TOP 12 button for more than 2 seconds to go back to the top of the disc and play the first track. 13 CD SCAN In CD play mode, press the INT 13 button to turn on intro playing first 10 seconds of each track. When wish to listen to the whole track during intro mode, press the button again to turn off intro.
20 CLOCK Press the CLK button to display the time on the LCD for 5 seconds. To adjust the time, press and hold the CLK button until the hour flashes and use the VOL 5 knob to adjust the hour. Press and hold the CLK button again until the minute flashes and use the VOL 5 knob to adjust the minute. 21 RADIO SCAN (Only from Remote) Pressing the SCN button from the remote control, the unit will scan and search for the next strong station while playing each station for 5 seconds with station number flashing.
M AINTENANCE OF REMOTE CONTROL Before using the remote control, the insulating patch must be removed. This patch was installed to insulate the battery from draining until ready to use. BATTERY INFORMATION: Lithium Battery: CR2025 3V Battery Life: Approximately 6 months. Replacing the Battery from the Remote Control: 1) Turn over the remote control so the rear side of the remote is facing up. 2) Remove the battery holder by pressing the locking tab with your thumb and pulling it out.
TROUBLE SHOOTING THE SYSTEM The following chart will help in solving most problems that may occur. Should any problem persist after you have made these checks, please consult your nearest Profile retailer. Before going through this check list, refer back to the wiring and operating procedures. ERROR CODES E 1~ E 10 The unit cannot be operated because of trouble. Press the "RESET" button 25 . If the indicator still appears after pressing the "RESET" button 25 , your unit needs repair.
SYMPTOM CAUSE SOLUTION The compact The installation angle is Adjust the angle of the unit to less than 30 disc skips. greater than 30 degrees degrees The disc player is installed Check to see if the unit is fastened securely incorrectly with the back brace supporting the rear of the unit. The compact disc is Clean the compact disc with a compact disc extremely dirty or defective cleaning solution or replace the defective disc. compact disc.
SPECIFICATIONS GENERAL Power Supply Requirements...........................................DC 12 Volts, Negative Ground || || || Chassis Dimensions ...............................................................7 (W) x 6 1/2 (D) x 2 (H) Tone Controls........................................................................................................................... Bass @ 100Hz..........................................................................................+10dB / -10 dB Treble @ 10Khz.......
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for repair (this period includes shipping time).
