Installation Sheet

ManualsBrandsPROFLO ManualsToiletsPROFLO Holyoke 1.28 GPF Toilet Tank Only - Left Hand Lever

Installation Instructions

HET Toilet Bowl and Tank

with 1.28 Gallons per Flush

Remove Old Toilet

1. Shut off water supply line to toilet. Flush toilet

and remove all water from the bowl and tank.

Use a sponge to absorb the water.

2. Disconnect the water supply from the tank.

3. Remove tank from bowl, use screwdriver and

adjustable wrench or socket wrench. Loosen

toilet bowl flange nuts under caps.

4. Remove old bowl by carefully lifting it off the

floor. Clean flange and plug drain with a rag to

prevent sewer gas from escaping.

Install New Toilet

1. If new installation, install a toilet flange into

waste line per flange instructions. Make sure

you have the correct rough in toilet.

2. Remove the rag from the drain. Install the

flange bolts into the flange.

3. Turn the bowl upside down and place it on the

flattened carton box to prevent damage.

4. Install a wax ring evenly around the bowl

flange, (horn).

5. Gently lower the bowl onto the flange making

sure the flange bolts protrude through the toilet

bolt openings.

6. Apply pressure evenly and rock the bowl from

side-to-side and front-to-back until it is firmly

on the floor.

7. Install the washers, nuts, and caps on the

flange bolts snug. Be careful not to over tighten

because the china may break.

8. Install the tank-to-bowl-gasket, tank bolts with

washer if it is not already installed, and place

tank on bowl.

9. Snug and level the tank nuts using a socket

wrench and holding the truss head screw

firmly inside the tank with a screwdriver.

10. Connect the water supply to the ballcock. Only

hand tighten the supply line. DO NOT USE

CHANNEL LOCKS.

11. Turn on water, flush, and check

for leaks.

Adjust ballcock to proper water line height as

noted on the flush valve tube.

Flange Bolts

Flange

Wax Ring

Sealant

Nut

Washer

Bolt

Rubber

Gasket

Tools Needed

A. Screwdriver

B. Wrench

C. Tape Measure

D. Level

E. Drill

F. Flange

G. Wax Seal

H. Marker

I. Plugs

J. Screws

K. Flexible Supply Line

L. Gasket Adapter

Distributed Exclusively by Ferguson, Stock Building Supply and Wolseley Canada

1. WARRANTY:

Subject to the limitations expressed herein,

Seller warrants to the original Buyer that parts

of products manufactured by Seller (“Products)”

shall be free from defects in material and

workmanship during the original installation from

the date of sale for the duration set forth in the

below table (“Warranty Period”). This warranty

is void for (a) improper storage, use or

installation, (b) accident, damage, abuse or

misuse, or (c) acts of God. This warranty does

not apply to damage caused by (a) exposure to

chemicals or minerals, (e) use of abrasive

cleaners, or (f) use of in-tank cleaners.

PRODUCT

PARTS

WARRANTY

PERIOD

Vitreous China

Lifetime

Parts & Fittings:

Tank Trim including

fill valve, flush valve,

flapper, trip lever and

plumbing fittings

5 years

Toilet seat

(if included with product)

1 year

Summary of content (6 pages)

PAGE 1
Installation Instructions HET Toilet Bowl and Tank with 1.28 Gallons per Flush Tools Needed A. B. C. D. E. F. Screwdriver Wrench Tape Measure Level Drill Flange G. H. I. J. K. L. H Wax Seal Marker Plugs Screws Flexible Supply Line Gasket Adapter A G C F B E 1. Shut off water supply line to toilet. Flush toilet and remove all water from the bowl and tank. Use a sponge to absorb the water. 2. Disconnect the water supply from the tank. 3.
PAGE 2
Installation Instructions HET Toilet Bowl and Tank with 1.28 Gallons per Flush Problem Solving Care & Maintenance • DO NOT use abrasive powered or liquid cleaners which can damage the product surface. • Over tightening of lock nut or coupling nut could result in breakage and flooding. • DO NOT use cone washer with plastic supply line. • DO NOT use pipe dope or other silicon based materials to tighten supply coupling nut. CAUTION Product is fragile.
PAGE 3
Instructions d'installation cuvette de toilette à haute efficacité et réservoir muni d'une 1.28 gallons par rougeur Outils et matériels nécessaires A. B. C. D. E. F. Tournevis Clé Ruban àmesurer Niveau Perceuse Bride G. H. I. J. K. L. Joint en cire Marqueur Bouchons Vis Conduite d'alimentation souple Adaptateur de joint Démontage de l'ancienne toilette 1. Fermez l'alimentation en eau de la toilette. Tirez la chasse d'eau et retirez toute l'eau de la cuvette et du réservoir.
PAGE 4
Instructions d'installation cuvette de toilette à haute efficacité et réservoir muni d'une 1.28 gallons par rougeur Entretien • N'utilisez pas de détergent abrasif en poudre ou en liquide qui risque d'endommager la surface du produit. • Si les contre-écrous ou les écrous de raccordement sont trop serrés, cela risque d'endommager l'appareil et d'inonder la pièce. • N'utilisez pas de rondelles avec la conduite d'alimentation en plastique.
PAGE 5
Instrucciones de instalación taza de inodoro de alta eficiencia y cisterna con 1.28 galones por rubor Herramientas y materiales necesarios A. B. C. D. E. F. Destornillador Llave Cinta métrica Nivel Taladro Reborde circular del desagüe del inodoro G. H. I. J. K. L. Sello de cera Marcador Conectores Tornillos Tubería flexible de suministro Adaptador de junta Desinstalación del inodoro viejo 1. Cierre la llave de suministro de agua al inodoro.
PAGE 6
Instrucciones de instalación taza de inodoro de alta eficiencia y cisterna con 1.28 galones por rubor Cuidado y Mantenimiento El problema que resuelve • No use limpiadores abrasivos en polvo o líquidos, ya que pueden dañar la superficie del producto. • Si se aprieta demasiado la tuerca de bloqueo o de acoplamiento, es posible que se rompa la superficie del producto, lo cual podría causar un desbordamiento de agua. • No use una arandela cónica en el caso de tuberías de plástico.