Model No. 831.14787.0 Serial No. Write the serial number in the space above for reference. USERʼS MANUAL Serial Number Decal • Assembly • Operation • Troubleshooting • Part List and Drawing CAUTION Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference. Sears, Roebuck and Co.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 PART IDENTIFICATION CHART . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on the vibration platform before using the vibration platform. Sears assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. 10.
19. Keep the power cord away from heated surfaces. 16. Use the vibration platform and the included dumbbells only as described in this manual. 20. Never leave the vibration platform unattended while it is running. Always unplug the power cord and switch the reset/off circuit breaker to the off position when the vibration platform is not in use. (See the drawing on page 5 for the location of the circuit breaker.) 17.
BEFORE YOU BEGIN cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual. Thank you for selecting the revolutionary PROFORM® ACTIVATOR V7 vibration platform. The ACTIVATOR V7 vibration platform offers whole body vibration options designed to make your workouts effective and enjoyable.
PART IDENTIFICATION CHART See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: Some small parts may have been preattached. If a part is not in the hardware kit, check to see if it has been preattached. If a part is missing, call 1-888-533-1333.
ASSEMBLY • For help identifying small parts, see the PART IDENTIFICATION CHART on page 6. Make Assembly Easier This manual is designed to ensure that the vibration platform can be assembled successfully by almost anyone. Most people find that if they set aside plenty of time, assembly goes smoothly. • Tighten all parts as you assemble them, unless instructed to do otherwise.
2. Tip: Be careful not to pinch the wires during this step. 2 With the help of a second person, carefully tip the Base (5) onto its side. 1 32 Attach the Lower Upright (1) to the Base (5) with two M10 x 55mm Patch Screws (20), two M10 Split Washers (38), two M10 x 68mm Bolts (55), and two M10 Nylon Locknuts (32). 55 5 20 3. Tip: Orient the Wheel Bracket (35) so that the arrow sticker is pointing upward.
5. Attach the Weight Rest (42) to the Weight Rest Frame (41) with eight M5 x 38mm Screws (40). Do not tighten the Screws yet. 5 42 40 40 41 40 6. Locate the wire tie inside the Upper Upright (36). Insert the wire tie through the hole in the Weight Rest Frame (41). 40 6 Next, attach the Upper Upright (36) to the Weight Rest Frame (41) with two M10 x 50mm Patch Screws (51) and two M10 Split Washers (38). 36 Wire Tie Hole 41 38 51 7.
8. Tip: Be careful not to pinch the wires during this step. 8 Attach the Upper Upright (36) to the Lower Upright (1) with four M10 x 20mm Patch Screws (28) and four M10 Split Washers (38). 36 See step 5. Tighten the eight M5 x 38mm Screws (40). 28 38 38 28 9. Tip: Orient the Handlebar (39) so that the sticker with an “R” is in the location shown. 9 Attach the Handlebar (39) to the Upper Upright (36) with two M10 x 62mm Patch Screws (37) and two M10 Split Washers (38). 37 38 39 36 10.
. Attach the back of the Console (3) to the Upper Upright (36) with two M4 x 16mm Patch Screws (26). Do not tighten the Screws yet. 11 3 26 36 12. While a second person holds the Front of the Console (3) near the Upper Upright (36), connect the console ground wire to the Ground Wire (52). Next, connect the console wire to the Wire Harness (43). Then, insert the wires into the Upper Upright. 12 3 Console Wire 43 36 13. Tip: Be careful not to pinch the wires during this step.
14. Set ten weight plates into the indicated slots in the right side of the Weight Rest (42). Next, lift the two selector pins on a Dumbbell (44), and slide the selector pins to the adjustment holes marked “2.5.” Place the Dumbbell on the weight plates. Then, lift the two selector pins and slide them to the adjustment holes marked “15.” 14 Selector Pins 44 44 Repeat this step with the other Dumbbell (44). Weight Plates Slots 42 15.
HOW TO USE THE VIBRATION PLATFORM HOW TO MOVE THE VIBRATION PLATFORM Before moving the vibration platform, unplug the power cord and remove the dumbbells from the weight rest. Handlebar Hold the handlebar and place one foot against the wheel. Tilt the vibration platform until it rolls freely on the wheel. Carefully move the vibration platform to the desired location. To reduce the risk of injury, use extreme caution while moving the vibration platform.
HOW TO PLUG IN THE POWER CORD This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available. DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock.
CONSOLE DIAGRAM CONSOLE FEATURES you do not do this, the console or other electronic components may become damaged. The console offers a selection of features designed to make your workouts more effective and enjoyable. You can change the time and frequency of your vibration sessions with the touch of a button. Plug the power cord into the receptacle on the base of the vibraReset tion platform (see Position assembly step 15 on page 12). Then, plug the power cord into a 120-volt outlet.
HOW TO USE THE MANUAL MODE HOW TO USE AN IFIT PROGRAM 1. Turn on the power. 1. Turn on the power. 2. Select the desired vibration time. 2. Insert an iFIT card and select a program. See HOW TO TURN ON THE POWER on page 15. See HOW TO TURN ON THE POWER on page 15. Press the desired time button to select a vibration time of 30, 45, or 60 seconds. The display will show which length of time you have selected.
TROUBLESHOOTING Inspect all parts of the vibration platform regularly. Replace any worn parts immediately. Outer surfaces of the vibration platform can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not use solvents to clean the vibration platform. Most vibration platform problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed.
PART LIST—Model No. 831.14787.0 Key No. Qty.
EXPLODED DRAWING—Model No. 831.14787.
Get it fixed, at your home or ours! Your Home For repair—in your home—of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears.com www.